Table of Contents
Advertisement
：
FOREWORD
Thanks for your purchasing this motorcycle.
With the help of this manual, you will learn the correct
procedures of operation and basic knowledge of maintenance
and trouble shooting of the motorcycle. It presents all
the basic knowledge of maintenance and trouble shooting
of the motorcycle. It presents all the details of the
performance of this motorcycle to you and the vehicle will
make your life more relaxed and happier.
In case any picture does not agree with the vehicle
physically, the latter shall prevail.
CAUTION．NOTE and MAIN POINTS
ings and should be carefully reviewed．
!CAUTION
：The personal safety of the rider may be
involved，disregarding this information could result in
injury to the rider．
NOTE
：These instructions point out special service
procedures or precautions that must be followed to
avoid damaging the machine．
MAIN POINTS
： This provides special information to make
maintenance easier or important instructions clearer．
VIN AND ENGINE SERIAL NUMBER LOCATION
the motorcycle．They are also use to assist your dealer
when ordering parts or special service information.
carry special mean-
The VIN is stamped on the front main beam of the frame．
of the crankcase assembly
VIN. :
Engine No.:
- 1 -
The VIN and/or engine serial number are used to register
The engine serial number is stamped on the rear end
Advertisement
Table of Contents
Related Manuals for Kinroad XT50QT-2
Summary of Contents for Kinroad XT50QT-2
- Page 1 VIN AND ENGINE SERIAL NUMBER LOCATION ： FOREWORD The VIN and/or engine serial number are used to register the motorcycle．They are also use to assist your dealer Thanks for your purchasing this motorcycle. when ordering parts or special service information. With the help of this manual, you will learn the correct procedures of operation and basic knowledge of maintenance and trouble shooting of the motorcycle.
-
Page 2: Table Of Contents
NOTES FOR SAFE RIDING CONTENTS RIDING APPAREL NOTES FOR SAFE RIDING……………………………2 1.Loose，fancy clothing can be uncomfortable and unsafe when riding your motorcycle ． Choose good quality LOCATION OF PARTS…………………………… …4 motorcycle riding apparel when riding your motorcycle． 2. most motorcycle accident fatalities are due to head INSTRUMENT PANEL……………………………... - Page 3 RULES FOR SAFE DRIVE MODIFICATION Check must be conducted before starting the engine to any modification of the motorcycle or removal of the prevent mishaps and damage to components. original equipment may render the vehicle unsafe or illegal Only the qualified person who has passed the drive P1ease obey national...
-
Page 4: Location Of Parts
LOCATION OF PARTS - 4 -... - Page 5 - 5 -...
- Page 6 1.Ignition switch/stolen-prevention lock 2.Electric starter switch 3.Lamp switch 4.Handlebar 5.Front brake lever 6.Right mirror 7.Fuel level indicator 8.The turn signals 9.speedometer lO.Left mirror 11.Switch to change the far and near light 12.Rear brake lever 13.Turn signals switch l4.Horn button - 6 -...
-
Page 7: Instrument Panel
INSTRUMENT PANEL HOW TO USE THE INSTRUMENT PANEL MAIN POINTS The indicator will stop at E position when the ignition switch is turned to OFF position. place the motorcycle on the center stand to read the number of the left fuel. ④THE TURN SIGNALS Turn the switch to“LEFT”or“RIGHT”position，the turn signal will flash to advise the driver．... -
Page 8: Using Methods Of Switches
USING METHODS OF THE SWITCHES THE IGNITION SWITCH The ignition switch control the start，the wiring diagram for lights and the lock for the handlebars． Please take the key with you when yon leave your motorcycle． (ON)it is connected． 1.You can start the engine． 2.You can drive 3.You can not take the key down (OFF)it is shut down．... -
Page 9: Light Switch
MAIN POINTS 1.If it is hard to lock，you can turn the handlebar to the right a little and then lock it. MAI N POINTS 2.Shake the handlebars left and right to be sure that Do not use the horn if un- necessary. it has been locked. -
Page 10: Using Methods Of Trunk
The front light switch has three positions, OPEN THE TRUNK And “●”(a white point). Open the seat when you want use the trunk or put the When the switch is in this position, the front helmet in it. head light ,tail and meter lights are all lit up. 1.put the ignition key in the lock of the seat and turn When the switch is in this position,the tail, to the right. -
Page 11: Add Gasoline And Engine Oil
MAIN POINTS 1.The trunk load capacity is 10kg． 2.Do not keep heat- Sensitive item in trunk when the trunk may get hot． 3.Do not keep valuable and easily damaged items in the trunk． 4.Keep the easily—flown items first in the plastic bag then put them in the trunk. - Page 12 - 12 -...
-
Page 13: Correct Driving Operations
NOTE 1. Don’t fill oil prior to the FULL level when adding CORRECT DRIVING OPERATIONS oil. 2.The engine will be easily damaged when driving STARTING METHOD OF THE ENGINE without oil. 3.Don’t mix oil with other type of oil and it will BEFORE STARTING affect the performance of the engine. - Page 14 MAIN POINTS The electric start will be un-functional if the brake levers are not squeezed． Don’t rotate the throttle handlebar when pressing the start button． [2]Hold the front and rear levers MAIN POINTS 1.After the engine is ignited，please release the start button to avoid affecting the engine．...
- Page 15 First confirm the following items then start again. [1]Turn the ignition switch to ON position. [2]Hold the rear brake lever with the left hand and press the front part of the seat with the right hand. [4] Preheat the engine while it is cool. [3]Kick the kick starter with the right foot.
- Page 16 Know well about the correct driving way. It is good not only for security， but also for the using [2]THE PROCEDURE TO DRIVE MOTORCYCLE life of your motorcycle．saving fuel and oil． Hold the handlebars with both hands, sit on the seat METHOD OF STARTING from the left．At this time.
- Page 17 NOTE If rotate the handlebar Of throttle too much，it may make the motorcycle run for-ward suddenly． ADJUST SPEED Adjust speed through rotating the handlebar of throttle． NOTE Note the cars from the back． [4] START Loosen the brakes and rotate the handlebar of throttle to make the motorcycle start gradually.
- Page 18 BE EXTRA SAFETY CONSCIOUS ON BAD WEATHER DAYS Riding on bad weather days ， especially wet ones requires extra Caution．Braking distance double on a rainy day．Stay off of the painted surface marks，manhole covers and greasy appearing areas as they can be especially slippery．...
- Page 19 Return the throttle and squeeze the front and rear brake levers. At the same time, the brake indicator is lit [3] Place the motorcycle on the center stand to inform the following drivers. place the motorcycle on the center stand on the place where does not affect traffic .
- Page 20 BREAK IN Check the following items before going to service Proper break-in is important to achieve maximum life station． and performance from your motorcycle． The engine can not be started? 1.The first month or the first 1000 km drive Check the following items again： with in 45km／h．...
- Page 21 PAY ATTENTION TO S ECURITY WHILE INS PECTING THE ENGINE IS OFF WHILE DRIVING NOTE Please check the following items; 1.Place the motorcycle on the center stand on a wide 1.Is there fuel? and plat place. If there is no fuel in the fuel tank, go to the nearby 2.Avoid hurting from the heat of engine and exhaust gas station to add fuel to the engine.
- Page 22 × × CHECK THE FUNCTION OF THE BRAKES Squeeze the brake levers to see if the play is between the standardized limits． 10∽20mm 10∽20mm more suitalbe less !CAUTION The abnormal tire pressure and tire crack ＆ damages and abnormal wearing are the mail causes to make unfunctional turning and explode the tires．...
- Page 23 CHECK LUBRICANT OF THE ENGINE Turn the ignition switch to ON position to see if the indicator 1it or not ， if it is lit， please add Lubricant oil to the engine. !CAUTlON Don’t make lubricant oil in the engine run off other - wise the engine will be damaged while driving.
-
Page 24: Periodical Inspections
Check if the front fork is bent or damaged．Check if there is abnormal noises while shaking the handle bars up and down． If the front fork is abnormal, consult KINROAD service PERIODICAL INSPECTION station. Periodical inspections are done by the riders them... - Page 25 10-20mm 10-20mm please refer to page 31 to adjust me brake lever play． FUNCTION OF THE BRAKES Tire pressure: front :175KPa Rear :225Kpa Check the front and rear brakes。function separately If the tires are abnormal，please go to dealers service by drive on the dry road with 1ow speed． station or replace them．...
- Page 26 CHECK THE FUNCTION OF THE LIGHTS ＆ THE TURN Check the oil pump and the oil tank to see if there SIGNAL INDICATOR is on leakage．If there is oil 1eakage p1ease ask KINROAD dealer to check and maintain it 1.Check the lights with the head light, turn signals...
-
Page 27: Simple Maintenance Methods
and the tail light． end of the levers should be 10-20mm 2.Check the lightness and direction of the lights by After adjusting the play, check that there is no making the light towards the wall dragging when turning rear wheel with the wheel off the 3.Start the turning indicator to check if it flashes ground and that there is enough clearance between the rear 60—120 times in one minute．... - Page 28 INSTALL AND ASSEMBLE THE FUSE Take the terminal from the battery, and take off the fuse !CAUTION Make the pin in the concave part of the adjuster from the terminal. otherwise, the clearance between the rear brake 1ever and grip will change when driving and it is very dangerous． MAIN POINTS Don’t touch the central part of the terminal after you take it down from the battery．...
- Page 29 correctly，injures and damages will happen． 1.Fire is forbidden，short circuit should be prevented, and smoke and other fire should be far form it． 2.Charge the battery in a ventilating place It is easily explosive in a closed place． 3.No intensive strike such as falling down． EMERGENCY METHODS If your skin or cloth has touched the battery liquid, wash with water immediately, If your eyes have it, wash...
- Page 30 !CAUTION 1.Gasoline and low ignition-point solvent is easily flammable, so please not use them when washing the air cleaner element. 2.Uncomplete assemblage will affect driving so make sure to assemble the air cleaner clement fixed. 3.Aviod water entering the air cleaner element when washing the motorcycle.
-
Page 31: Specifications
SPECIFICATIONS 50CC 50CC 39 mm×41.4 mm Overall length 1670mm Cylinder bore × stroke 9.2:1 Overall width 640mm Compression ratio 2.0kw/7500r/min Overall height 1060mm Output(max) 3.0N.m/4500r/min Wheelbase 1190mm Torque(max) 1500r±100r/min Dead weight 78kg Idling speed Payload 150kg Displacement of cylinder 49 ml 3.50-10 Spark plug Front wheel... -
Page 32: Electrical Diagram
ELECTRICAL DIAGRAM - 32 -...
Need help?
Do you have a question about the XT50QT-2 and is the answer not in the manual?
Questions and answers