Table of Contents
Advertisement
Quick Links
User Guide
Babysense2 is included as a
medical device on the Australian
Register of Therapeutic Goods
(ARTG No. 97479)
Babysense2 is intended for use as an Infant Apnoea Alarm.
ALWAYS READ THE LABEL AND USER GUIDE, USE ONLY AS DIRECTED.
Please retain your purchase receipt and attach to the back page of this
user guide. You will need to produce this if warranty service is required.
Advertisement
Table of Contents
Related Manuals for Oricom babysense 2
Summary of Contents for Oricom babysense 2
- Page 1 User Guide Babysense2 is included as a medical device on the Australian Register of Therapeutic Goods (ARTG No. 97479) Babysense2 is intended for use as an Infant Apnoea Alarm. ALWAYS READ THE LABEL AND USER GUIDE, USE ONLY AS DIRECTED. Please retain your purchase receipt and attach to the back page of this user guide.
-
Page 2: Table Of Contents
Customer Support and Express Warranty (Australia) .....15 Express Warranty (Australia) ..........16 Need Help? If you need assistance setting up or using your Oricom Babysense2 now or in the future, call Oricom Product Support. Australia 1300 889 785 or (02) 4574 8888 www.oricom.com.au... -
Page 3: Important Use And Safety Warning
Important Use And Safety Warning IMPORTANT USE AND SAFETY WARNING It is essential that all users of your Babysense2 monitor read and understand this user guide thoroughly before installing or using the product. This user guide contains detailed information on installation and operation of the Babysense2 monitor which all users need to be aware of to ensure that the monitor operates properly. - Page 4 Important Use And Safety Warning WARNING: To avoid possible danger of strangulation from cords, keep the cords out of reach of children. Ensure that excess cords are secured with the included cable tie. • Do not place the cords in a high "wear and tear" location. •...
-
Page 5: General Information
• One control unit holder • One hanging hook • Two sensor pads • Two reuseable plastic cable ties Requires 4 AA size, 1.5 volt high quality Alkaline batteries (not supplied). If any items are missing from the pack please call Oricom Customer Support. -
Page 6: Technical Specifications
General Information Technical Specifications • Powered by 4 size AA, 1.5 volt high quality Alkaline batteries (not supplied). Power consumption approx. 1mA. • Battery life approx. 6 months using high quality alkaline batteries. • Alarm volume typically 85dB SPL at distance of one metre from control unit. •... -
Page 7: Installation
Installation Installation 1. Remove battery cover by inserting a flat screw driver into the opening recess and insert, in accordance with the markings, 4 new and identical size AA 1.5 volt high quality Alkaline batteries, close cover. Note: Please dispose of used batteries in accordance with local waste regulations. - Page 8 Installation 4. Sensor pad installation: • When using for infant not yet able to crawl, place one sensor pad as shown in illustration 3. Make sure the sensor is placed underneath baby’s location in crib. • When baby begins to crawl, and is able to move onto areas not "covered"...
- Page 9 Installation 6. Attach end(s) of the cord(s) to the outlets marked "SENSOR" on the back of control unit (as shown in illustration 5 and 6). When using one sensor pad, attach to any “SENSOR” outlet. PLEASE NOTE: Do not attach any cable to the blocked socket, marked "DO NOT USE".
- Page 10 Installation 7. Should the design of the cot not allow proper installation with the control unit holder, please use the supplied hanging hook (as shown in illustration 6). Hang the control unit from the bottom edge of the cot or affixthe hook with a screw (not supplied) to the bottom edge of the cot and hang the control unit from the bottom edge of the cot.
- Page 11 Installation 9. Place mattress firmly on top of sensor pads. When using with a slat based cot, ensure the sensor pads are stable & supported adequately. If the mattress cannot be in direct contact with the sensor pads, or if the cot base is soft or padded, place plywood (not supplied) on the cot base, place the sensor pads on the plywood and place the mattress firmly on top to enable full contact of the sensor pads with the...
-
Page 12: Operation
Operation Operation Babysense2 is ready for operation and use once the installation is complete. To operate, follow the instructions below: • Place your baby in crib/cot. • Turn control unit on by pressing On/Off button. • Red control lights switch on briefly and a double click sound is heard. •... - Page 13 Operation Testing Operation You must conduct this quick performance test daily. • The performance test should be conducted while baby is not in cot and if there are any fans, air conditioning units, cot mobile, humidifier, ceiling projector etc in the babies room, please ensure you conduct the daily performance test with these devices turned on if applicable.
- Page 14 Babaysense2. Do not use Babysense2 with a memory foam mattress. • In case of false alarms, kindly refer to troubleshooting guide. Please contact Oricom Customer Support team with any product related questions. Please note Babysense2 monitors and alerts with respect to breathing movement rates, but cannot prevent cessation of breathing.
- Page 15 2 years of use. To order replacement sensor pads (2B0013) contact Oricom Support (02) 4574 8888 or 1300 889 785, support@oricom.com.au Hisense Ltd. is an ISO 9001:2008 and ISO 13485:2003 certified company.
-
Page 16: Troubleshooting Guide
ATTENTION: Should false alarms sound as a result of reduced sensitivity, increase the level of sensitivity and then perform the Performance Test. For all product related questions and warranty support please call Oricom Customer Support team on 1300 889 785 or (02) 4574 8888. -
Page 17: Customer Support And Express Warranty (Australia)
Express Warranty (Australia) Oricom International Pty Ltd is the distributor of Babysense2 in Australia. This Express Warranty is provided by Oricom International Pty Ltd ABN 46 086 116 369, Unit 1, 4 Sovereign Place, South Windsor NSW 2756, herein after referred to as “Oricom”. -
Page 18: Express Warranty (Australia)
No change to the conditions of this Express Warranty is valid unless it is made in writing and signed by an authorised representative of Oricom. Oricom will not be liable under this Express Warranty, and to the extent permitted by law will not be liable for any defect, loss, damage or injury arising out of or in connection with a: 1. -
Page 19: Australia
Please note that if a Customer Support Team member advises that your product does not qualify for return, this warranty does not apply to your product. Products that are authorised to be returned to Oricom in Australia must include all of the following: •... -
Page 20: Australia
Phone: 1300 889 785 or (02) 4574 8888 (Monday to Friday 8am to 6pm AEST) Web: www.oricom.com.au Fax: (02) 4574 8898 Contact Details for Oricom Support and Warranty Claims in New Zealand Email: support@oricom.co.nz Phone: 0800 674 266 (Monday to Friday 10am to 8pm NZST) Web: www.oricom.co.nz...
Need help?
Do you have a question about the babysense 2 and is the answer not in the manual?
Questions and answers