1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Security Camera
  5. VCC-4324P
  6. Instruction manual

Sanyo VCC-4324P Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
VCC-4324P

Advertisement

Table of Contents
loading

Related Manuals for Sanyo VCC-4324P

Summary of Contents for Sanyo VCC-4324P

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL VCC-4324P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. Be sure to keep it handy for later reference.

  • Page 2: Table Of Contents

    Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • The optical filter is switched automatically to colour image or black CONTENTS and white image according to the subject brightness.

  • Page 3: Precautions

    Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.

  • Page 4: Parts Names

    PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. External sync composite video signal input connector (VBS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor.
  • Page 5 PARTS NAMES Flange-back adjustment lever (See page 9) Flange-back lock screw Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings.

  • Page 6: Concerning Auto-Iris Lenses

    ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the A.I. LENS switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm...

  • Page 7: Mounting The Lens

    MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 5 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera.
  • Page 8 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.

  • Page 9: Connections

    CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Connect an AC 24 V power source to the 24 V AC connectors on the back of the camera. Insert the plug of this power cord into a wall outlet.

  • Page 10: Flange-Back Adjustment

    FLANGE-BACK ADJUSTMENT If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below.

  • Page 11: Settings

    SETTINGS C • B/W (colour/black and white) switch setting e f g h This switch lets you select the timing of the automatic switching of the optical filter to colour image or black and white image, according C-BW VR301 LEVEL to the subject brightness.

  • Page 12: White Balance Adjustment

    SETTINGS High speed electronic shutter setting White balance adjustment Normally, the speed setting switches for the high speed electronic Normally the WB (white balance) switch is set shutter are all set to the OFF position. This sets the electronic shutter to the A (automatic) position and the white speed to 1/50 sec.

  • Page 13: Backlight Compensation Setting

    SETTINGS Lens iris adjustment Backlight compensation setting If using a DC type auto-iris lens, you will need to set the LEVEL Use an auto-iris lens and set the EI/BLC switch to the BLC-ON (VR301) volume when shooting in the conditions described below. position, to engage the backlight compensation function.
  • Page 14 SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the When using an auto-iris lens (for indoor/outdoor shortest F stop. Set the EI/BLC switch to the EI-ON position. use) Set the EI/BLC switch to the OFF position. CAUTION: If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD.
  • Page 15 SETTINGS Line phase adjustment Set the SYNC switch to the L-L position. SYNC When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. In such a case, set as described below. Switch the display on the monitor from camera 1 to camera 2.

  • Page 16: Troubleshooting

    This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. However, in the event of a problem, the owner is advised not to attempt to make repairs or open the cabinet. Servicing should always be referred to your dealer or Sanyo Authorized Service Centre.

  • Page 17: Specifications

    SPECIFICATIONS Camera: Scanning system : PAL standard Lens mount : CS mount (or C mount with the (625 TV lines, 25 frames/sec.) supplied adaptor) Interlace : PLL 2:1 interlace Environmental conditions : Temperature: –10˚C ~ +50˚C Humidity: less than 90% Image device : 1/3 inch solid state image device (no condensation)
  • Page 18 Sanyo Electric Co, Ltd. 1AC6P1P2090-- Printed in Japan L53S4/XE(0599KP-Si)

Table of Contents