Hubsan X4 Instruction Manual
  1. Manuals
  2. Brands
  3. Hubsan Manuals
  4. Quadcopters
  5. X4 DESIRE
  6. Instruction manual

Hubsan X4 Instruction Manual

Hide thumbs Also See for X4:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual, User Manual
®
2.4GHZ RC SERIES 4 CHANNEL
Flip tips kindly check page 15-17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hubsan X4

Summary of Contents for Hubsan X4

  • Page 1 ® 2.4GHZ RC SERIES 4 CHANNEL Flip tips kindly check page 15-17...
  • Page 2 H107D SPARE PART CHART H107D-A01 H107D-A06 H107-A23 H107D-A03 Body Shell Props Motor X4 FPV RX H107-A24 H107-A06 H107-A07 H107D-A05 Battery USB Charger Screw Set Transmitter H107D-A02 H107-A11 H107C-A19 H107-A13 Rubber feet U wrench M8 Protection Cover T-Shirt H107-A32 H107C-A33 H107D-A04...

  • Page 3: Important Notes

    175MB. Thank you for buying HUBSAN products. The quadcopter is designed as an easy to use, full Answer：When the SD card is properly formatted in the TX, it will use special formatting that splits featured RC model capable of hovering, fast forward, and aerobatic ight manoeuvres.
  • Page 4 30 minutes. Check the battery connection. Do not attempt to disassemble or modify or repair the LiPo battery. If the transmitter battery power is low, you will need to replace with new AA batteries . THE HUBSAN X4 THE HUBSAN X4...
  • Page 5 If you don't want to save it please power o the TX. • Before operation, please check the batteries of the transmitter and receiver are charged Please check the battery in both TX and X4, when the battery is low, it can’t record. enough for the ight.
  • Page 6 Press the shaft down from the top of the prop and motor to x the problem, or replace the motor. 12. The arm of the X4 separates after a hard landing or crash. Answer: This is a special design to absorb the impact from hard crashes. Simply force the arms to snap back into the joint position by hand as shown in the picture.

  • Page 7: Input Key Function

    H107D FAQ 1.Transmitter and X4 will not bind. Input Key Function Answer: Throttle position needs to be fully minimized. Please do not move the transmitter sticks or trims during initial power-on binding. Identi cation Function 2. Transmitter LED light came on and then suddenly went o .

  • Page 8: Exploded View

    The TX and X4 will not bind if the batteries are low. Please replace with new batteries. 5. If the batteries in the TX are running low whilst ying the X4, you will still have control. Please land the X4 and then replace batteries in the TX.
  • Page 9 ELEVATOR stick to the left. Hold down the ELEVATOR stick for 2 seconds to exit. Remove the props. Position the cover’s four holes with the motors. Press each of them on the motors, then re-install the props in their correct positions on the X4 . 0:08:49...

  • Page 10: Li-Po Battery Charging

    5 LI-PO BATTERY CHARGING In Expert Mode, the X4 can y at high speeds and do ips. if you don’t need 5.1 The quadcopter is equipped with a 3.7V 380mAh Lipo battery it to ip, you can select anti- ip mode. Press the throttle stick to select or deselect anti- ip.

  • Page 11: Video Recording

    6.3 Start/Stop recording using the remote. WARNING! First activate the camera before flight in order to make sure the SD card is formatted. Formatting while in flight will result in loss of control. MODE 2 MODE 1 THE HUBSAN X4 THE HUBSAN X4...

  • Page 12: Start To Fly

    Your X4 can do 360° ips by pushing the joysticks as described below. For other stick or trim before the TX and X4 match code and bind, or the X4 will drift. The TX proper ip execution, make certain that the X4 is close to level, within a 30° angle with LED will turn green when the TX binds with the X4.
  • Page 13 Normal mode Set Real Time Elevator : After a “beep”, and the red LED on the transmitter turns green, the 6 lights on the X4 Format SD Card Aileron : will be on solid indicating that the bind code is matched. The LEDs will be on and...

  • Page 14: Advanced Performance Setup

    3. First learn to master hovering, then master ying a square or rectangular pattern by recognizing features that are picked out before you begin your FPV ight. 4. The X4 prop guard is excellent to use indoors if required for your personal skill level, but MODE 2 MODE 1 using outside is optional and less desirable in many cases.

Table of Contents