Contents Precautions ................1 Product Introduction ..............3 Introduction to Appearance and Keypad ........4 Get Started ................5 Charge the Built-in Lithium Battery ........5 Use of Memory Card .............. 6 Startup/Shutdown ..............7 Conversion between Modes ........... 8 Indicator Light .................
This user's manual has referred to the latest information we had when this user’s manual was made. The screen display and illustrations are used in this user's manual for the purpose of introducing details of this video camera in a more specific and direct way.
Page 4
the surface of video camera or its lens. If it is required to clean video camera surface, firstly blow away the sand dust accumulated on this surface, and then wipe the video camera gently with rag or tissue applicable to optical equipment.
Product Introduction This product is small in size and easy for installation. With high-performance chips, this product can produce high-definition videos with excellent continuity of dynamic images, even under low illumination conditions, and supports H.264 HD video format. ...
Get Started Charge the Built-in Lithium Battery To charge the camera, connect it to the computer via the USB cable. Then, the charge indicator light (red) will be on. After the camera is fully charged, the charge indicator light will be off. In general, it can be fully charged after 2-4 hours.
Use of Memory Card Push the microSD card into the card slot according to the direction instruction beside the slot of memory card till it is completely inserted. To take out the microSD card, gently press the memory card inward and it will pop up. microSD card NOTE:...
Startup/Shutdown Startup: Press and hold the POWER button for 2 seconds. The screen of the display is activated and the camera is turned on. Shut down: Press the POWER button again will shut down the camera. Auto Screen-off: When the idle time of the camera reaches the automatic screen-off time, it will turn off the screen to save power.
Conversion between Modes The camera has four modes: Video recording mode, Photo mode, Vehicle mode and Playback mode. These modes can be switched over by clicking the icon on the upper left corner of the LCD display after startup. Video recording mode Photo mode Vehicle mode Playback mode...
Video Recording Mode After turning on the camera, it will directly go to the video recording mode. You can start recording videos by pressing the shutter button. To stop video recording, just press the shutter button again. When the memory card is full or the battery power drops to a low level, the camera will also automatically stop the video recording.
Photo Mode After turning on the video camera, it will directly get to the video recording mode. To switch to the photo mode, click the mode icon on the upper left corner of the LCD display. You can shoot a photo by pressing the shutter button. Mode: Indicating that camera is currently in photo mode.
Vehicle Mode The length of each recording file is 3 minutes. Mode: Indicating that the camera is in the vehicle mode. Video size: Available in FHD (30fps) / HD (60fps/30fps) / VGA (120fps). Recording time: indicating the available length of remaining time to be recorded.
Playback Mode After turning on the camera, press the Playback icon ( ) in the lower right corner of the LCD display. Then click on the mode icon ( ) to activate the corresponding menu. Normal video files Vehicle video files Photo files Playback video clips (normal video and vehicle video): Click...
Page 15
Click to pause the playing. Click to fast forward the playing. Click to fast rewind the playing. Click to stop the playing. Playback photos: Click the icon then you can view photos by clicking the icon “◄” or “►”. File deletion After clicking the Delete File icon , the screen will appear as shown in the right figure.
Connecting the Camera to High-Definition TV Connect the camera to a High-Definition TV with HDMI cable (not included). Then video signals from the camera will be automatically output to the High-Definition TV. HDMI Cable Connection diagram HDMI Cable Signal transmission Application on the Personal Computer Connect the camera with a computer via the USB cable.
Application of Remote Control Signal transmission port OFF key REC key SNAP key While using the remote control, place its signal transmitter port toward the infrared signal receiver light of the camera. Then you can record videos, take photos or shut down the camera by pressing the corresponding buttons.
Waterproof Case Using Notice Before sealing the waterproof case, keep the camera housing’s rubber seal clean, a single hair or dust or sand can cause the leakage. You can test by closing the case without inserting the camera. Submerse the case completely in water for about a minute.
Technical Parameters Image Sensor CMOS Video recording mode, photo mode, Function Mode vehicle mode, playback mode Camera Lens F3.1 f=2.9mm Digital Zoom Shutter Electronic shutter LCD Display 6.1 cm (2.4”) touch screen Screen 12M (4000x3000) / 10M (3648x2736) / Image Resolution 8M (3264x2448) / 5M (2560×1920) FHD: 1920x1080 @ 30fps...
Page 20
Service Procedure If you have reason for complaint, or your device is defective, please contact your dealer or the service division of JAY-tech GmbH to make arrangements for service procedures. Service Hours: Monday - Thursday from 8:00 am to 5:00 pm Friday from 8:00 am to 2:00 pm.
Need help?
Do you have a question about the SportCam D528 and is the answer not in the manual?
Questions and answers