Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Precision ANA-DIGI SERIES
Summary of Contents for Precision ANA-DIGI SERIES
- Page 1 ANA-DIGI SERIES...
- Page 2 CONTENTS INTRODUCTION 2 - 16 : SOLAR POWER DIGITAL AND ANALOGUE DIAL WATCH INSTRUCTIONS 17 - 18 : PRECISION GUARANTEE AND WARRANTY...
- Page 3 After reading the manual please keep it in a safe place for future reference. Your Precision watch is a world band (multi frequency) watch. It incorporates a highly sensitive radio receiver that receives time signals from the UK, Europe, US and Japan according to the time zone setting on the watch.
- Page 4 SOLAR POWER DIGITAL AND ANALOGUE DIAL WATCH INSTRUCTIONS SIGNAL CROWN DISPLAY MENU OPERATION DIAGRAM...
-
Page 5: Main Features
MAIN FEATURES • Solar powered • Automatic Radio Controlled time setting for UK (MSF), USA (WWVB), Germany (DCF) and Japan (JJY 60Khz only) • Time zone setting by 31 major cities • 3 levels signal strength indicator • Reception indicator •... - Page 6 Automatic Time Setting Your Precision Watch receives the available Atomic Clock signal automatically at 3:00am every night according to the Time Zone setting (go to Time Zone setting for details. Everything is done automatically. Battery Management When the battery level is low, the LCD display shows a flashing, empty battery icon and the seconds hand runs 2 steps every 2 seconds.
- Page 7 LI G HT SOLAR POWER RECHARGING Your Precision watch is charged by all ambient light, whether that is from a natural or ar- For artificial light, use a flourescent lamp at a distance of 8cm tificial power source. Avoid overheating as it will damage the watch permanently.
- Page 8 BUTTON FUNCTIONS (SEE OPERATION DIAGRAM PAGE 2) • Press and release S1 once to check if the reception is OK • Press twice to show the battery level for around 5 seconds • Press and hold S1 for 3 seconds for Manual Signal Reception Press to set LCD display to show: •...
- Page 9 Manual Signal Reception • Holding S1 for more than 3 seconds until the LCD display shows the Antenna icon. There is one digit on the right hand side of the display showing the signal to receive. Where US=WWVB, J4=JJY40, J6=JJY60, UK=MSF and DE=DCF. At the same time, the second hand pauses at 12 o’clock during signal reception (for all Time Zones).
- Page 10 Time Zone Setting USA users must set the watch to one of the following time zones: Time Zone Reading on LCD Eastern NYC (New York, USA) CHI (Chicago, USA) Central Mountain DEN (Denver, USA) Pacific LAX (Los Angeles, USA) 1. Hold S2 (the lower right button) for 3 seconds while the watch is in the normal time keeping mode until the LCD displays a City name (3 digits City code) 2.
- Page 11 PLEASE NOTE: Make sure you check the battery level is at least half-full before doing the time zone Setting. If the battery level is not half-full, charge up the watch until it reaches this level. Daylight Saving Time On/Off (for travelling purposes) The daylight saving time of your watch is preset to on.
- Page 12 • Push S1 to switch the day from English to German language or vise versa. • Push S2 to confirm. Manual Time Setting Your watch sets itself automatically. This manual time setting is an option only in case there is no signal around after the battery is replaced.
-
Page 13: Troubleshooting
Watch Hands (hour, minute and second hand) Alignment The watch hands need to be aligned when the watch hands are shifted 1. Pull out the crown when the second hand is at 12:00:00 to stop it from running 2. Rotate the crown to set Hour and Minute hands at 12:00:00 3. - Page 14 If your watch is unable to make contact with the radio signal, it will continue to function in the same way as a standard watch. The time will then be corrected the next time your watch receives the time signal. Watch Stops or Runs 2 Steps Every 2 Seconds When the battery level is low, the LCD shows a flashing empty battery icon and the second hand runs 2 steps every 2 seconds.
- Page 15 Reset the Watch Pull out the crown when the second hand has paused at 12:00:00 to stop it from running Rotate the crown so that the Hour and Minute hands are aligned at 12:00:00. Don’t push in the crown. Hold S2 for around 10 seconds and then release the button Push in the crown The hands start normal running The LCD display shows “LON”.
- Page 16 1. Hold S2 (bottom right button) and do not release 2. Then hold S1. Now you are holding 2 buttons at the same time 3. Hold these buttons until the second hand spins to a new position 4. Then judge 1 •...
- Page 17 After Battery Replacement After battery replacement, the LCD displays “Set to 12”. Make sure the crown is pushed-in and the second hand is running normally Pull out the crown when the second hand is at 12:00:00 to stop it from running Rotate the crown to set Hour and Minute hands at 12:00:00 Then push-in the crown The LCD display shows “LON”.
- Page 18 How to Check the Battery Level Whilst the Watch is Sleeping When the watch is sleeping, press any button once to show the battery level for one minute. The watch will go to sleep again by a push of S1 or it will sleep again if no button is pressed after one minute.
- Page 19 We cannot be held liable for loss or damage without this remittance. All products should be returned to: Precision House, Starley Way, Birmingham International Park, Bickenhill Lane, Solihull, B37 7GNR If you would like more information concerning the comprehensive radio controlled product ranges offered by Precision then please look at www.precisiontimekeeping.com...
- Page 20 Important Notice with regards to the use and replacements of all batteries and the disposal of this product Only use the recommended batteries. Do not dispose of batteries in fires or general waste. Please recycle where facilities exist. Check with your local authority for recycling advice. This product is classified as an electronic product and should not be disposed of in your general rubbish.
- Page 21 WARRANTY REPAIR FORM NAME ADDRESS PHONE NUMBER EMAIL FAULT DESCRIPTION...
- Page 22 www.precisiontimekeeping.com...
Need help?
Do you have a question about the ANA-DIGI SERIES and is the answer not in the manual?
Questions and answers