Movement & Sound Monitoring Settings - Angelcare AC401 Quick Setup Manual

Step 5: Testing your Angelcare Monitor (continued)
7. If the alarm does not sound,
the SensorPad may be detecting
a continuous vibration from (e.g.)
the fl oor, a strong draught or
vibrating items (e.g. cot mobiles),
or the baby's bed is being
touched.
DO NOT touch baby's bed whilst
testing the monitor. Place baby's
bed near a solid supporting wall
and away from strong drafts.
ADJUSTING THE SENSITIVITY
OF THE SENSORPAD
1. The standard setting is approx.
level 3, which is suitable for most
bed sizes and types of
mattress. DO NOT ADJUST
UNLESS NECESSARY
2. The sensitivity of the SensorPad
can be increased (highest level
5, suitable for larger beds or
thicker mattresses) or decreased
Step 6: Menu Access & Changing Settings
Your Angelcare Monitor has
5 different menus which provide full
access to all monitor settings. You
can access the MENU and change
the settings as follows:
1. Turn both units ON
2. Press the MENU button briefly
to enter MENU 1 or press MENU
again to go to the NEXT MENU
(see point 7)
Menu 1
Movement & Sound Out of Range Setting
Monitoring Settings
Step 6 Menu 1: Movement & Sound Monitoring Settings
Consumer Helpline: 0845 009 1789 | www.angelcare-uk.co.uk
(lowest level 1, suitable for
smaller beds and if there a
possibility of external vibrations)
using the dial on the back of the
Nursery Unit
3. By increasing the sensitivity the
SensorPad will cover a larger
area (e.g. bigger beds or thicker
mattresses), BUT it could also
detect vibrations from outside the
baby's bed, e.g. mobiles, etc
4. It is important to fi nd the
right balance for your situation to
ensure optimal performance of
the SensorPad
5. ALWAYS test the performance
after moving and reinstalling the
Angelcare Monitor in a different
place or when the bed or
mattress has changed
3. The relevant icons of the selected
settings will become visible or
start fl ashing
4. The settings can be changed
using the ARROWS UP and
DOWN
5. Always press SELECT to
confirm your setting
Menu Options Loop
Menu 2 Menu 3
Sound Transmission
Settings
Functions Tic function: The 'tic' is a
sound that tells you that
your SensorPad is detecting
movements. This function can
only be activated together with
the Movement function.
Sound function: Activates the
sound transmission between
the parent unit and the nursery
unit.
Factory Tic, Sound & Movement function activated
Setting
6. NEVER USE THE SENSORPAD
WITH A MEMORY FOAM
MATTRESS!
TEST STOPPING THE ALARM
To stop the alarm:
1. Place your hand lightly on
the mattress again so that
the SensorPad starts detecting
movement
2. Turn the Nursery Unit OFF (then
restart the monitor by turning the
Nursery Unit ON again)
TEST THE BATTERY MODE
Always check if the battery mode is
functional by operating both units
without the AC adapters. If the green
BATTERY light on the Nursery Unit
does not light up, the batteries need
to be replaced. If the display on the
Parent Unit does not appear, it needs
to be recharged. See also Step 7 for
further instructions.
6. Press EXIT to exit the menu if
you are fi nished with
programming or press MENU to
forward to the next MENU
7. The menus are in a loop so each
time you press the MENU button
briefl y you forward to the next
MENU in the following order:
Menu 4 Menu 5
Alarm Settings Temperature Control
Settings
Movement function: Activates
the SensorPad. It will detect
your baby's movements and
sound an alarm when there
is no movement after 20
seconds. Please ensure the
SensorPad has been installed
and tested according to the
instructions in Steps 1 and 5.
Page 6