Table of Contents
Advertisement
Quick Links
15GEL & NGEL Series
Horizontal Grinders
Series:
15
Governor Option:
Governed
N
Non-Governed
Grinder:
Nose Terminations:
E
Extended
Throttle Terminations:
L
Lever
Generation:
C
Third
RPM:
90
140
120
180
For additional product information visit our website at http://www.clecotools.com
NORTH AMERICA
CooperTools
P .O. Box 1410
Lexington, SC 29071
15
X G
E
L
C
-
XXX
Operation & Service Manual
823069
-
X
X
X
X
Guard:
Terminations:
3
3/16
6M
6mm
4
1/4
5
5/16
6
3/8
Wheel Type:
W
Type 1 Wheel
C
Collet
P
Plug
Extensions:
Standard
6
6" Extension
EUROPE
Cooper Power Tools GmbH & Co.
Postfach 30
D-73461 Westhausen
4/01
25
2 1/2
3
3 In.
4
4 In.
3T
3/8-24
4T
1/2-13
5T
5/8-11
1
Advertisement
Table of Contents
Related Manuals for Cleco 15GEL Series
Summary of Contents for Cleco 15GEL Series
- Page 1 Operation & Service Manual 823069 4/01 15GEL & NGEL Series Horizontal Grinders Guard: Series: 2 1/2 3 In. Governor Option: 4 In. Terminations: Governed 3/16 Non-Governed Grinder: 3/8-24 Nose Terminations: 1/2-13 5/16 5/8-11 Extended Throttle Terminations: Wheel Type: Lever Type 1 Wheel Generation: Collet Plug...
- Page 2 (6.2 bar) does not exceed rated free speed stamped on tool. Grinders in use on the job must be checked at least once every 20 Cleco grinders are designed to operate on 90 psig (6.2 bar) max. hours of operation, or once a week, whichever is most frequent.
- Page 3 • It is not equipped with proper wheel guard • It starts to vibrate Cleco CHECK FLANGE • You sense changes in tool speed or an MODEL SERIAL NO.
- Page 4 Some tasks require more than one type of tool to obtain possibly any combination of all three. the optimum operator/tool/task relationship. Cleco offers a com- plete selection of tools including vertical, straight, angle, and The use of quality abrasive wheels which are well balanced,...
-
Page 5: Proper Lubrication
The governor,if so equipped, should be checked periodically to be sure the governor mechanism is clean, in good operating condi- Proper repair procedures and the use of original Cleco service tion, and functioning properly. parts and bearings rather than substitutes will return the tool to... - Page 6 TYPE 1 WHEEL GUARD MOUNTING Wheel Guard Wheel Dia. Part No. 2-1/2"(62mm) 202277 3"(75mm) 202278 4"(100mm) 202245 Wheel Guard Bolt (Torque to Spindle End Nut Driving Flanges (Recessed) 30 to 40 in. lbs.) Wheel Dia. Thread Size Part No. Wheel Dia. Thread Size Part No.
-
Page 7: Operating Instructions
REASSEMBLY- GENERAL The tool is reassembled in the reverse order of disassem- The 15GEL Series Grinders are designed to operate on 90 bly. Clean parts in a solvent and inspect for damage or psig (6.2 bar) maximum air pressure, using a 3/8" hose up wear. -
Page 8: Extension Housing
EXTENSION HOUSING Side Exhaust Deflector When using 4" wheel guard 202245, 1-3/8" O.D. driving flange 202256 and 1-3/8" O.D. outer flange Type Tool Part No. Type 1 Wheel 202251 CAUTION 865991 (3/8-24) or 202336 (1/2-13) must be used. Collet 202254 Fee speed (RPM) of the grinder must not exceed speed (RPM) of the Type 1 wheel. -
Page 9: Motor Unit
MOTOR UNIT Gov. 847095 Part No. Non-Gov. 843444 9000 867082 865663 12000 867083 867388 Gov. 202246 14000 867084 Non-Gov. 202321 865686 18000 867085 864821 865687 These parts are included 867086 864821 in governor 865663 864234 subassembly Gov. 864232 867388 Non-Gov. 869055 202247 812164... - Page 10 HANDLE ASSEMBLIES 202105 202106 LEVER (GOVERNED) 843590 869855 869856 863093 847808 841552 865698 864375 847710 864530 202337 844311 865701 843590 844304 864387 832595 864531 202105 202106 LEVER 869855 (NON-GOVERNED) 845409 847808 202104 869712 202103 202322 203043 846664 869489 847767 847272 PART NO.
- Page 11 NOTES...
- Page 12 CooperTools 670 Industrial Drive Lexington, SC 29072 Phone: (803) 359-1200 Fax: (803) 359-2013 www.clecotools.com...
Need help?
Do you have a question about the 15GEL Series and is the answer not in the manual?
Questions and answers