Do you have a question about the FLUID2 and is the answer not in the manual?
Questions and answers
David G. White
March 19, 2025
trainer makes a "grinding" or "rumbling" noise when starting or changing speeds. Pls. advise correction
1 comments:
Mr. Anderson
March 19, 2025
The grinding or rumbling noise in a CycleOps FLUID2 trainer when starting or changing speeds could be caused by the resistance unit. This may happen due to air bubbles in the fluid resistance unit, which can create noise until they dissipate. It could also result from improper setup, such as an unlevel trainer or incorrect rear wheel tension. Ensuring proper assembly, wheel alignment, and checking for any loose components may help reduce the noise.
Page 1
OWNER’S MANUAL FOR THE FLUID , MAGNETO, MAG, MAG+, AND WIND TRAINERS. PARTS LIST | Listado de piezas | Liste des pièces | Teileliste | Elenco parti | Onderdelenlijst If you do not nd all of these items in the box, please contact customer service at 800.783.7257.
Page 2
PRECAUTIONS | PRECAUCIONES | PRÉCAUTIONS ÉLÉMENTAIRES | VORSICHTSMASSNAHMEN | PRECAUZIONI | VOORZORGSMAATREGELEN Before starting any exercise program, consult with your physician or health professional. He or she can help establish the exercise frequency, intensity and time appropriate for your particular age and condition. If you have any pain or tightness in your chest, an irregular heartbeat, shortness of breath, feel faint, or have any discomfort while you exercise, STOP! Consult your physician before continuing.
TRAINER SETUP AUFBAU DES TRAININGSGERÄTS MONTAJE DEL APARATO DE ENTRENAMIENTO IMPOSTAZIONE RULLO MONTAGE ET RÉGLAGE DE E L’APPAREIL D’ENTRAÎNEMENT MONTAGE VAN HET TRAININGSTOESTEL 1.1: Fully extend trainer legs and set trainer on at surface. The foot pads on the legs of the trainer can be rotated to make your trainer stand level on uneven surfaces.
1.5: Turn resistance unit knob clockwise to engage the L-bolt to the resistance unit. 1.5: Gire el pomo de la unidad de resistencia en el sentido de las agujas del reloj para engranar el perno en forma de L en la unidad de resistencia. 1.5: Tournez la molette de l’unité...
9703 MAG+ REMOTE SHIFTER 9703 MAG+ REMOTE SHIFTER 9703 CAMBIADOR REMOTO DE MAG+ 9703 CAMBIO REMOTO PER MAG + 9703 DÉRAILLEUR À DISTANCE 9703 MAG+ SCHAKELAAR OP AFSTAND 9703 MAG+ Remote Shifter Mag/Mag+ Resistance Unit Cambiador remoto Mag/Mag+ Unidad de Dérailleur à...
Page 7
5.4 Allentare o aumentare la tensione del cavo del cambio avvitando o svitando il cilindro di regolazione (a). 5.4 U kan de spankracht op de versnellingskabel instellen door de stelschroef (a) losser of vaster te draaien. 5253 Verona Road Madison, WI 53711 21849 02/14 B www.cycleops.com 1-800-783-7257...
Need help?
Do you have a question about the FLUID2 and is the answer not in the manual?
Questions and answers
trainer makes a "grinding" or "rumbling" noise when starting or changing speeds. Pls. advise correction
The grinding or rumbling noise in a CycleOps FLUID2 trainer when starting or changing speeds could be caused by the resistance unit. This may happen due to air bubbles in the fluid resistance unit, which can create noise until they dissipate. It could also result from improper setup, such as an unlevel trainer or incorrect rear wheel tension. Ensuring proper assembly, wheel alignment, and checking for any loose components may help reduce the noise.
This answer is automatically generated