1. Manuals
  2. Brands
  3. Qvis Manuals
  4. IP Camera
  5. AMB-EYE1.3
  6. User manual

Qvis AMB-EYE1.3 User Manual

1.3 / 2 / 3 mega pixel eyeball dome ip cameras
Hide thumbs
Table of Contents

Advertisement

Quick Links

AMB-EYE1.3
AMB-EYE2
AMB-EYE3
1.3 / 2 / 3 MEGA PIXEL EYEBALL DOME IP CAMERAS
User's Manual
V2.0 06 / 2014

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AMB-EYE1.3 and is the answer not in the manual?

Questions and answers

Related Manuals for Qvis AMB-EYE1.3

Summary of Contents for Qvis AMB-EYE1.3

  • Page 1 AMB-EYE1.3 AMB-EYE2 AMB-EYE3 1.3 / 2 / 3 MEGA PIXEL EYEBALL DOME IP CAMERAS User’s Manual V2.0 06 / 2014...
  • Page 3 Welcome Thank you for purchasing the: 1.3, 2 or 3 Mega Pixel Eyeball Dome IP Cameras This user’s manual is designed to be a reference tool for the installation and operation of your system. Here you can find information about the corresponding IP camera’s features and functions, as well as a detailed installation method.
  • Page 4 Important Safeguards and Warnings 1．Electrical safety  All installation and operation here should conform to your local electrical safety codes.  The power supply shall conform to the requirement in the SELV (Safety Extra Low Voltage) and must make sure that the limited power source is rated 12V DC or 24V AC. Please note: Do not connect two power supplying sources to the device at the same time;...
  • Page 5  Please make sure the CCD (CMOS) component is away from the radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component damage.  It is recommended that the grounding studs of the product should be grounded, so to further enhance the reliability of the camera.

  • Page 6: Table Of Contents

    Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 1.3.1 Performance ......................2 Structure ............................5 Components ........................5 Framework and Dimension ..................6 Device Installation ........................7 Installation Steps ......................7 Restore Factory Default Setup Introduction ............. 9 Quick Configuration Tool ......................

  • Page 7: General Introduction

     Supports web access.  Allows network camera configuration and management via Ethernet. Network  Supports device management via web or client-end. Management  External power adapter DC12V. Power  Supports s PoE supply © Copyright Qvis ®. All documentation rights reserved.

  • Page 8: Specifications

    Supports day/night mode switch Gain Control Fixed/Auto White Balance Manual/Auto On/Off Manual/Low Noise/Low motion blur/Auto Exposure Mode PAL: It ranges from 1/3 to 1/10000 NTSC: It ranges from 1/4 to 1/10000 H.264/JPEG/MJPEG Video Compression Standard © Copyright Qvis ®. All documentation rights reserved.
  • Page 9 396 (18*22) detection zones；sensitivity level ranges from 0 to 100 Motion Detect Activation event: video storage, image snapshot, log, email function and etc. Record Priority Manual>Video detect>Schedule Storage Support FTP storage. Management © Copyright Qvis ®. All documentation rights reserved.
  • Page 10 Power 4W MAX, DC 12V Consumption Working C ~+60 Temperature Working ≤95% Humidify Φ113×86 Dimensions(mm) Weight 280g(Excluding box) 400g (Excluding box) 280g (Excluding box) Installation Fixed on the wall, ceiling, etc. © Copyright Qvis ®. All documentation rights reserved.

  • Page 11: Structure

    Component Name Component 1 Device lens Component 2 Dome body Component 3 Dome enclosure Port Name Connector Note Network connect standard Ethernet port Ethernet. To connect to DC12V power DC12V power supply. © Copyright Qvis ®. All documentation rights reserved.

  • Page 12: Framework And Dimension

    2.2 Framework and Dimension Please refer to the following two figures for dimension information. The unit is mm. See Figure 2-2 and Figure 2-3. Figure 2-2 Figure 2-3 © Copyright Qvis ®. All documentation rights reserved.

  • Page 13: Device Installation

    Line up the three spigots of the decoration ring to the jags from the bottom to the top and then turn clockwise until you hear a clear sound ”KA”. Now the installation is complete. Figure 3-1 © Copyright Qvis ®. All documentation rights reserved.
  • Page 14 This series product supports two cable exits. One is from the bottom and the other is from the side. Please refer to the following figure for cable exit from the side information. Figure 3-3 © Copyright Qvis ®. All documentation rights reserved.

  • Page 15: Restore Factory Default Setup Introduction

    Step5: Put the dome back to the dome cover. Please refer to Step 4 in Chapter 3.1 to install the decoration ring back. Figure 3-5 © Copyright Qvis ®. All documentation rights reserved.

  • Page 16: Quick Configuration Tool

    The factory default user name is admin and password is admin. For security reasons, please modify your password after you first login. For detailed WEB operation, please refer to the Network Camera Web Operation Manual in the resource CD. © Copyright Qvis ®. All documentation rights reserved.
  • Page 17 Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-4. In Figure 4-4, you can view device IP address, user name, password and port. Please modify the corresponding information to login. © Copyright Qvis ®. All documentation rights reserved.
  • Page 18 After you logged in, the configuration tool main interface is shown as below. See Figure 4-5. Figure 4-5 Main interface For detailed information and operation instructions of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD. © Copyright Qvis ®. All documentation rights reserved.

  • Page 19: Web Operation

    2. The login interface is shown as below. See Figure 5-2. 3. Please input your user name and password. 4. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login. © Copyright Qvis ®. All documentation rights reserved.
  • Page 20 If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download. Or you can lower the web browser’s security level. See Figure 5-3. Figure 5-3 IE security level © Copyright Qvis ®. All documentation rights reserved.
  • Page 21 After you logged in, you can see the main window. See Figure 5-4: Figure 5-4 Web monitoring window © Copyright Qvis ®. All documentation rights reserved.

  • Page 22: Faq

    Note  This user’s manual is for reference only. Slight differences may be found in user interface.  All the designs and software here are subject to change without prior written notice. © Copyright Qvis ®. All documentation rights reserved.
  • Page 23 For more information about our IP Cameras and other available cameras, NVRs & accessories, please visit our website: www.adata.co.uk Alternatively scan this QR code with your smart phone to be directed instantly to our website: © Copyright Qvis ®. All documentation rights reserved.

This manual is also suitable for:

Amb-eye2Amb-eye3

Table of Contents