Chamberlain MyQ 888LM Installation Manual

APPLICATION
The MyQ Control Panel is intended to be installed with Security✚™
®
Garage Door Openers manufactured between 1998 and present. The
MyQ Control Panel is NOT compatible with Security✚ 2.0™ Garage Door
®
Openers. DO NOT install this door control on garage door opener
systems controlling one-piece or swing doors.
OVERVIEW
The MyQ Control Panel offers a quick and convenient way to add
®
Security✚ 2.0™ and MyQ technology to your existing garage door
®
opener. MyQ technology uses a 900MHz signal to provide two-way
®
communication between the garage door opener and MyQ
accessories. When programmed to the Liftmaster
can monitor and control your garage door from any internet enabled
computer or smartphone. You may program up to 12 Security✚ 2.0™
remote controls, 2 Security✚ 2.0™ keyless entries and a combination of
16 MyQ accessories to the MyQ
®
COMPATIBLE ACCESSORIES
Security ✚ 2.0™ Accessories:
Model 891LM
1- Button Remote Control
Model 893LM
3-Button Remote Control
Model 890MAX
3-Button Mini MAX Remote Control
Model 893MAX
3-Button MAX Remote Control
Model 895MAX
3-Button Premium MAX Remote
Control
Model 877LM
Wireless Keyless Entry
Model 877MAX
Wireless MAX Keyless Entry
INSTALLATION
Install the MyQ Control Panel in place of the existing door control. Due
®
to power consumption the MyQ
conjunction with another wired door control connected to your garage
door opener. If an additional door control is needed, the wireless door
control model 885LM can be programmed to the MyQ
To program the 885LM to the MyQ
control programming steps. When in battery back-up mode, any feature
using unattended operation such as Timer-to-Close, closure from a
garage door and gate monitor or remote operation utilizing the
LiftMaster Internet Gateway will be disabled.
®
1. Disconnect all electrical and battery power (if applicable) to the
garage door opener.
2. Remove the existing door control from the wall.
3. Note the polarity of the wires connected to the existing door
control.
• Label the wire connected to the RED terminal.
• Label the wire connected to the WHITE terminal.
Disconnect the wires from the existing door control.
For more information, please visit www.devancocanada.com or call toll free at 855-931-3334
enabled
®
Internet Gateway you
®
control panel.
®
MyQ Accessories:
®
Model 823LM
Remote Light Switch
Model 825LM
Remote Light Control
Model 828LM
LiftMaster Internet Gateway
®
Model 829LM
Garage Door and Gate Monitor
Control Panel cannot be used in
®
Control Panel.
®
Control Panel, follow the remote
®
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 7-28 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m), and away from ALL
moving parts of door.
• NEVER permit children to operate or play with door control push
buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER
permit anyone to cross path of closing garage door.
• DO NOT install this door control on garage door opener systems
controlling one-piece or swing doors.
To provide an adequate visual alert, the garage door opener light
bulb(s) MUST be a minimum of 40 Watt (or equivalent).
4. Connect the wires to the new MyQ
polarity is correct.
• Red wire to the R terminal.
• White wire to the W terminal.
5. Mount the MyQ Control Panel to the wall.
®
6. Reconnect power. The yellow command LED and the red learn LED
will blink quickly for up to 5 minutes as the control panel
recharges. When the control panel is operational, the yellow
command LED will glow steadily.
7. To test the control panel, press the push bar to activate the garage
door opener.
Existing Door Control
Wire from
WHITE
terminal
Wire from
RED terminal
Discard, donate
or recycle
1
MyQ CONTROL PANEL
®
MODEL 888LM
Control Panel. Make sure the
®
MyQ Control Panel
®
Connect
WHITE
wire to W
terminal
Connect
RED wire to
R terminal