Page 1
KD-SC900R SERVICE MANUAL CD RECEIVER 49829 2003 KD-SC900R Area Suffix E ------------- Continental Europe EX ---------------- Central Europe TABLE OF CONTENTS Important Safety Precautions ............1-2 Disassembly method .
KD-SC900R SECTION 1 Important Safety Precautions 1.1 Safety Precautions Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 3
KD-SC900R 1.2 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
KD-SC900R SECTION 2 Disassembly method 2.1 Main body 2.1.1 Removing the front panel assembly Front panel assembly (See Fig.1) (1) Push the detach button in the lower left part of the front panel assembly and remove the front panel assembly in the direction of the arrow.
Page 5
KD-SC900R 2.1.3 Removing the heat sink (See Fig.5) (1) Remove the two screws C and one screws D on the left side of the main body. Heat sink Fig.5 2.1.4 Removing the bottom cover (See Figs.6 and 7) • Prior to performing the following procedure, remove the front Joint d panel assembly, front chassis assembly and heat sink.
Page 6
KD-SC900R 2.1.5 Removing the rear bracket (See Fig.8) Rear bracket • Prior to performing the following procedure, remove the front panel assembly, front chassis assembly, heat sink and bottom cover. (1) Remove the three screws E, one screws F and two screws G on the back of the body.
Page 7
KD-SC900R 2.1.8 Removing the front board (See Figs.11 to 13) • Prior to performing the following procedure, remove the front panel assembly. (1) Remove the four screws K on the back side of the front panel assembly. (2) Release the ten joints g.
Page 8
KD-SC900R 2.2 CD Mechanism Assembly 2.2.1 Removing the top cover (See Figs.1 and 2) (1) Remove the two screws A on the both side of the body. (2) Lift the front side of the top cover and move the top cover backward to release the two joints a.
Page 9
KD-SC900R 2.2.2 Removing the connector board Wires (See Figs.3 to 5) CAUTION: Before disconnecting the flexible wire from the pickup, solder the short-circuit point on the pickup. No observance of this in- struction may cause damage of the pickup. (1) Remove the screw B fixing the connector board.
Page 10
KD-SC900R 2.2.3 Removing the DET switch (See Figs.6 and 7) (1) Extend the two tabs c of the feed sw. holder and pull out the switch. (2) Unsolder the DET switch wire if necessary. DET switch Connector board Pickup Fig.6...
Page 11
KD-SC900R 2.2.4 Removing the chassis unit (See Figs.8 and 9) • Prior to performing the following procedure, remove the top Chassis unit cover and connector board. Suspension spring (L) Suspension spring (R) (1) Remove the two suspension springs (L) and (R) attaching the chassis unit to the frame.
Page 12
KD-SC900R 2.2.5 Removing the clamper assembly (See Figs.10 and 11) • Prior to performing the following procedure, remove the top cover. (1) Remove the clamper arm spring. Clamper arm spring (2) Move the clamper assembly in the direction of the arrow to release the two joints d.
Page 13
KD-SC900R 2.2.6 Removing the loading / feed motor assembly (See Figs.12 and 13) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw C and move the loading / feed motor assembly in the direction of the arrow to remove it from the chassis rivet assembly.
Page 14
KD-SC900R 2.2.7 Removing the pickup unit Pickup unit (See Figs.14 to 18) • Prior to performing the following procedure, remove the top cover, connector board and chassis unit. (1) Remove the screw D and pull out the pu. shaft holder from Part e the pu.
Page 15
KD-SC900R 2.2.9 Removing the trigger arm Joint k (See Figs.19 and 20) • Prior to performing the following procedure, remove the top cover, connector board and clamper unit. (1) Turn the trigger arm in the direction of the arrow to release Trigger arm the joint k and pull out upward.
Page 16
KD-SC900R 2.2.11 Removing the mode sw. / select lock arm Link plate Joint t (See Figs.22 and 23) Mode sw. • Prior to performing the following procedure, remove the top plate assembly. Select lock arm (1) Bring up the mode sw. to release from the link plate (joint t) and turn in the direction of the arrow to release the joint u.
Page 17
KD-SC900R 2.2.12 Reassembling the mode sw. / select lock arm Select lock arm spring (See Figs.24 to 26) Hook w REFERENCE: Reverse the above removing procedure. Joint v (1) Reattach the select lock arm spring to the top plate and set...
Page 18
KD-SC900R 2.2.13 Removing the select arm R / link plate Joint c' Link plate Joint r (See Figs.27 and 28) Select arm R Joint b' • Prior to performing the following procedure, remove the top plate assembly. (1) Bring up the select arm R to release from the link plate...
Page 19
KD-SC900R 2.2.15 Removing the loading roller assembly Loading roller assembly (See Figs.31 to 33) • Prior to performing the following procedure, remove the Roller guide clamper assembly and top plate assembly. spring (1) Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint g' of the lock arm rivet assembly.
Page 20
KD-SC900R 2.2.16 Removing the loading gear 5, 6 and 7 Loading gear bracket (See Figs.35 and 36) • Prior to performing the following procedure, remove the top Loading gear 6 cover, chassis unit, pickup unit and top plate assembly. (1) Remove the screw K attaching the loading gear bracket.
Page 21
KD-SC900R 2.2.17 Removing the gears Joint p' (See Figs.37 to 40) • Prior to performing the following procedure, remove the top Change plate cover, chassis unit, top plate assembly and pickup unit. rivet assembly • Pull out the loading gear 3. (See Fig.35.) (1) Pull out the feed gear.
Page 22
KD-SC900R 2.2.18 Removing the turn table / spindle motor Turn table (See Figs.41 and 42) • Prior to performing the following procedure, remove the top cover, connector board, chassis unit and clamper assembly. (1) Remove the two screws L attaching the spindle motor as- sembly through the slot of the turn table on top of the body.
Page 23
KD-SC900R 2.3 Finder Plate Design Model Name : KD-SC900R Factory Setting Design Name : CARBON BLACK Design Name : LEOPARD Design Name :SAPPHIRE BLUE Design Name : SILVER HAIRLINE (No.49829)1-23...
Frequency Band 6. Digital tester 87.5 MHz to 108.0 MHz 7. Tracking offset meter AM(MW) 522 kHz to 1620 kHz 8. Test Disc JVC :CTS-1000 (LW) 144 kHz to 279 kHz 9. Extension cable for check EXTSH002-22P 1 Dummy load Exclusive dummy load should be used for AM,and FM.
Page 25
KD-SC900R 3.2 Flow of functional operation unit TOC read Power ON When the laser diode correctly Set Function CD When the pickup correctly moves emits to the inner area of the disc Microprocessor $82 $81 Disc inserted Microprocessor commands commands 3.3V...
Page 26
KD-SC900R 3.2.1 Feed section Is the voltage output at Is the wiring for IC501 Is 3.3V present at IC501 IC541 pin "40" 5V or 0V? pin 27? pin "20"? Check CD 8V Check the vicinity of and 5V. IC541. Is 4V present at both...
Page 27
KD-SC900R 3.3 Maintenance of laser pickup 3.4 Replacement of laser pickup (1) Cleaning the pick up lens Before you replace the pick up, please try to clean the lens Turn off the power switch and,disconnect the with a alcohol soaked cotton swab.
Page 30
KD-SC900R 4.3 BR24C16F-X (IC771) : EEPROM • Pin layout • Pin function Symbol Function Power supply. A0,A1,A2 No use connect to GND. Serial clock input. Serial data I/O of slave and ward address. Write protect terminal. • Block diagram 16kbit EEPROM allay...
Page 32
KD-SC900R 4.6 LA4743K (IC301) : Power amp. • Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F PWR GND2...
Page 33
KD-SC900R • Pin layout • Pin function Pin No. Symbol Function Pin No. Symbol Function Header of IC FLIN Front Lch input Power GND RLIN Rear Lch input Outpur(-) for front Rch ONTIME Power on time control STDBY Stand by input...
Page 34
KD-SC900R 4.7 LA6579H-X (IC501) : 4-Channel bridge driver • Pin layout & Block diagram VIN1-A VIN1 VIN1_SW [H]: OP-AMP_A [L]: OP-AMP_B VIN1+A VIN1-B VCCP1 VIN1+B Signal system S-GND power supply VIN1-SW All outputs ON/OFF H : ON VO2+ MUTE MUTE...
Page 35
KD-SC900R • Pin function Pin No. Symbol Function VIN1-A CH1 input AMP_inverted input VIN1+A CH1 input AMP_non-inverted input VCCP1 CH1 and CH2 power stage power supply VO1+ Output pin(+)for channel 1 VO1- CH1 output pin (-) for channel 1 VO2+...
Page 36
KD-SC900R 4.8 NJM4565M-WE (IC581) : CD L.P.F. A OUTPUT A INPUT B OUTPUT B INPUT A INPUT B INPUT 4.9 NJU7241F25-X (IC461) : Regulator • Pin layout GND 1 5 STB VIN 2 VOUT 3 4 NC • Block diagram...
Page 37
KD-SC900R 4.10 NJU7241F33-X (IC471) : Voltage regulator PIN FUNCTION 1. GND 2. V 3. V 4. +NC 5. STB 4.11 RPM6938-SV4 (IC602) : Remote control receiver • Pin diagram • Block diagram Comp Rout Detector conversion trimming circuit magnetic shield...
Page 38
KD-SC900R 4.12 SAA6579T-X (IC71) : RDS detecter • Pin layout QUAL DATA Vref OSCO OSCI TEST SCOUT MODE • Block diagram ANTI- 57 kHz OSCILLATOR QUALITY BIT RECONSTRUCTION ALIASING BAND PASS GENERATOR FILTER FILTER (8th ORDER) DIVIDER COSTAS LOOP BIPHASE...
Page 41
KD-SC900R • Pin function Pin No. Symbol Function 3.3V power supply pin Main-beam amp input pin Main-beam amp input pin Sub-beam amp input pin Sub-beam amp input pin Monitor photo diode amp input pin Laser diode amp output pin APC circuit ON/OFF control signal, laser diode (LDO) control signal input or bottom/peak detection frequency change pin.
Page 42
KD-SC900R 4.15 TC94A14FA (IC541) : DSP & DAC • Terminal layout & block daiagram Clock generator 1-bit Servo control Digital equalizer Address automatic circuit adjustment circuit Data CLV servo slicer 16 k Synchronous guarantee decoder Audio out Digital circuit output...
Page 43
KD-SC900R Symbol I/O Descroption TMAX O TMAX detection result output pin. TMAX Detection Result TMAX Output Longer than fixed period "PV " Within fixed period "HiZ" Shorter than fixed period "AV " LPFN I Inverted input pin for PLL LPF amp.
Page 44
KD-SC900R 4.16 TC94A20F-011 (IC401) : CD-ROM decoder + MP3 decoder with DAC and SRAM • Pin layout • Block diagram Switch General Timing inputbport generator 1-44 (No.49829)
Page 45
KD-SC900R • Pin functions Pin No Symbol Functions /RESET Hard reset input H:normal L:reset MiMD Micon I/F mode select input /MiCS Micon I/F chip select input /MiLP Micon I/F latch palus input MiDio I/O Micon I/F data input/output /MiCK Micon I/F clock input...
Page 46
KD-SC900R 4.17 UPD784217AGC195 (IC701) : CPU • Pin Layout • Block Diagram Pin No. Symbol Function CDRESET Not use CDMUTE Not use CD mecha SW2 CD mecha position setting SW Loading motor control output 0 Loading motor control output 1...
Page 47
KD-SC900R Pin No. Symbol Function EPROMDO I2C data output EPROMCK I2C clock output OPEN DOOR OPEN SW External DAC IC chip select output CCLK External DAC IC control data output CDTI External DAC IC control data output Power down mode output SD/ST Station detector or stereo indicator input ;...
Page 48
KD-SC900R 4.18 TEA6320T-X (IC161) : E.volume • Pin layout OUTRR OUTLR OUTRF OUTLF Vref MUTE CD-CH TAPE TUNER • Block diagram VOLUME 2 MUTE 0 to 55 dB FUNCTION BALANCE ZERO CROSS FENDER REAR POWER DETECTOR SUPPLY VOLUME 1 BASS...
Page 50
KD-SC900R VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY MOBILE ENTERTAINMENT CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.49829) Printed in Japan 200304WPC...