1. Manuals
  2. Brands
  3. Hobby Manuals
  4. Motorhomes
  5. 2015 Vantana
  6. Manual

Hobby 2015 Vantana Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Van Vantana
MANUAL
GB
Version 02/2015

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2015 Vantana and is the answer not in the manual?

Questions and answers

Related Manuals for Hobby 2015 Vantana

Summary of Contents for Hobby 2015 Vantana

  • Page 1 Van Vantana MANUAL Version 02/2015...
  • Page 2 Introduction Dear Camper, Congratulations on the purchase of your new HOBBY van. The trust you have placed in us is both an incentive and an obligation to continuously implement new ideas, technical innova- tions and fine touches to make our vehicles even better.

  • Page 3: Table Of Contents

    Introduction 00-1 Chapter 1: Introduction Tyres ............... 04-1 General information ..........01-1 Tyre pressure ............04-2 Designations in the operating instructions ..... 01-2 Tread depth ............04-3 Wheel rims ............. 04-3 Chapter 2: Safety Fast tyre repair kit ..........04-4 General information ..........
  • Page 4 Introduction 00-2 Safety instructions ..........07-1 12.3 Airing ..............12-2 Elements of the electrical system ......07-1 12.4 Care ................ 12-3 Electric power supply ........... 07-19 12.5 Winter Lay Up for the van ........12-8 Electrical system ..........07-28 12.6 Winter Operation ...........

  • Page 5: Introduction

    This will ensure guarantee claims for any of the equipment. Your HOBBY van has been built in accordance with the latest In accordance with guarantee conditions, HOBBY's dealer technology and approved safety regulations. Despite all pre-...

  • Page 6: Designations In The Operating Instructions

    Introduction 01-2 1.2 Designations in the operating instructions Handling instructions Handling instructions are also given in the form of key words beginning with the symbol “•“. This manual explains the motor home in the following manner: Notes Texts and illustrations Texts that refer to illustrations are found directly below the Notes point out important details that ensure your van and illustrations.
  • Page 7 Introduction 01-3 Optional Extras You have selected a mobile home that is equipped to taste. This user manual describes all of the models and equipment offered within the same programme. Therefore, it may include equipment that you have not selected. Differences and, thus, all of the optional extras are marked with an asterisk „...
  • Page 8 Introduction 01-4...

  • Page 9: Chapter 2: Safety

    02-1 Safety Chapter 2: Safety 2.2 Fire protection Precautions against fire 2.1 General information • Never leave children alone in the vehicle. • Keep inflammable materials away from all heating and • Operating and user instructions for built-in equipment (re- cooking devices.

  • Page 10: Equipment

    Safety 02-2 2.3 Equipment 2.3.1 Emergency equipment To be prepared in case of an emergency, you should always carry the three emergency devices on board and familiarize yourself with them. First-aid kit 100 m The first-aid kit should always be at hand and have a fixed B e i f a h r e r s e i t e K 6 5 V A N T A N A 2 0 1 5 position in your van.

  • Page 11: Vehicle Tool Kit

    02-3 Safety 2.4 Before driving 2.4.1 What to observe before taking your first drive Vehicle registration Every vehicle that drives on public roads must be registered. This also applies to your new van. Apply for registration at your local Driver and Vehicle Licensing Agency. You must show the following when applying for registration: registration document, Part II / CoC...
  • Page 12 Road Traffic Licensing Regulations must be officially authorised! If you have any further questions or difficulties, your autho- rised Hobby dealer will always be available to assist you! • Tighten the nuts on the wheels after driving the first 50 miles with your camper.

  • Page 13: Before Each Drive

    02-5 Safety 2.4.2 Before each drive Road safety • Before driving, check that the signalling and lighting systems (switch on battery circuit breaker), steering and brakes function correctly. • If the vehicle has been standing for a longer period of time (approx.
  • Page 14 Safety 02-6 Storage space in the rear Preparing the vehicle When loading the rear of the van, please observe the permissible Check the exterior of the vehicle and carry out the following axle loads and the technically permissible maximum weight. preparations before driving: Preparing the vehicle: •...
  • Page 15 02-7 Safety Interior Gas bottles may only be transported when they are secu- rely fastened in the gas bottle container provided. Some preparations must also be carried out inside the van. Preparing the interior Ensure that there is sufficient ventilation. Never cover up •...

  • Page 16: While Driving

    02-8 Safety • Only install children's car seats on seats that have been fitted by the manufacturer with three-point belts. • Turn the swivel seats in the direction of traffic and lock them into place. The seats may not be turned while driving. •...
  • Page 17 02-9 Safety Braking • Long descents with a slight gradient can become dangerous. Adjust your speed from the very beginning to allow you to The following applies for braking: speed up if necessary without endangering other automobiles. • Not the longer braking distance, especially on wet roads. •...

  • Page 18: After Driving

    Safety 02-10 2.6 After driving Switching electric consumption: Selecting a parking space The following applies when switching electric consumption: • Switch the refrigerator from 12 V to accelerator or 230 V. The following applies for selecting a parking space: Otherwise, if the engine is not on, the 12 V electrical supply •...

  • Page 19: Chapter 3: Chassis

    In addition, the VIN is also given on the type plate of the base vehicle as well as on the Hobby type plate (in the motor compartment on the upper front cross member of the radiator).

  • Page 20: Loading

    Chassis 03-2 3.3 Loading If you are not sure whether or not you have overloaded the vehicle, you should have it weighed at a public weighing 3.3.1 General information facility. Overloading can cause the tyres to break down or even Rules for loading: burst! This increases the danger that you may lose control • Spread the load evenly between the left and right-hand...
  • Page 21 1. Technically permissible overall mass Weight of an 11 kg aluminium bottle: Information regarding the technically permissible maximum Weight of 11 kg gas inflation: weight is based on Hobby Wohnwagenwerk's specification in cooperation with the manufacturers of the previous construc- Total: 16,5 tion stages (Fiat). This mass takes into account the specific...
  • Page 22 These optional extras will be shown in the actual mass of and kitchen fittings, food, camping equipment, toys, pets). the vehicle if − they are not part of the standard scope of equipment, The remaining additional load (5.) must always be greater than − Hobby or the manufacturer of the base vehicle were re- or equal to the minimum loading capacity (6.); this must be taken into account when determining the configuration of the vehicle. sponsible for assembling them, − the customer can order them.

  • Page 23: Entrance Step

    03-5 Chassis 3.4 Entrance step To open • Press the switch in the entrance area. The entrance step will be extended automatically. The vans are equipped with an electrically extendable entran- ce step To close • Press the switch in the entrance area. Do not step on the entrance step until it has been comple- The entrance step will be retracted automatically.

  • Page 24: Towing Fixture

    Chassis 03-6 Due to stipulations by the manufacturer of the basic vehicle and the fixing of the so-called D value of the towing fixture no additional loading of the towing loads is possible. 3.5 Towing fixture The maximum towing weight, trailer load and tow bar load are set out in Chapter 14 "Technical Data". Please ensure that the permissible drawbar load, maximum towing weight and rear axle load for the van are not excee- ded, especially when the rear of the van is used as storage space after the bed has been converted.

  • Page 25: Externally Mounted Fixtures

    3.6 Externally mounted fixtures 3.7 Automatic transmission Registering accessories in the vehicle's documents As an option, your van can be equipped with an automatic • Have your HOBBY dealer mount your externally mounted transmission (Fiat: Comfort-Matic) which has two methods fixtures. of operation: MANUAL/gearshift and AUTO(MATIC). Since • Take your van to a technical support organisation or tech-...
  • Page 26 Chassis 03-8 Parking the vehicle These three positions are not fixed, i.e. after the lever has been moved it jumps back to the centre position. To ensure that the vehicle is safely parked, step on the brake pedal and then shift into either first gear or reverse (R). Further- Manual operation more, when parking on a slope, you must also pull the hand This method of operation allows the driver to select a suitable brake.
  • Page 27 Chassis 03-9 For further information, please refer to the operating in- structions for the base vehicle. Please familiarise yourself sufficiently with the operation of the automatic transmissi- on before you use your vehicle the first time.
  • Page 28 Chassis 03-10...

  • Page 29: Chapter 4: Wheels, Tyres

    • Never drive an overloaded vehicle. be checked regularly to ensure that they fit tightly. Tubeless tyres have been mounted on your HOBBY van. Un- Tightening torque for wheel nuts and bolts: der no circumstances may tubes be inserted in these tyres!

  • Page 30: Tyre Pressure

    04-2 Wheels and tyres Snow chains Never drive faster than 50 km/h. Do not use snow chains on snow-free roads. Snow chains can only be mounted to tyres that are just as large as the tyres originally mounted on your vehicle. Snow chains may only be mounted on the front drive wheels;...

  • Page 31: Tread Depth

    04-3 Wheels and tyres 4.5 Wheel rims If the pressure is too low, this may cause overheating of the tyre, possibly resulting in severe damage to the tyre. Only use the rims noted in the registration documents. Should you wish to use other rims, please note the following. For the correct inflation pressure, please refer to the table in the chapter on “Technical Data“...

  • Page 32: Fast Tyre Repair Kit

    Wheels and tyres 04-4 The fast tyre repair kit can be used when the outside tempera- ture ranges from -20°C to + 50°C. Please refer to the FIAT manual for instructions on how to use the fast tyre repair kit. There is an expiry date on the sealant.

  • Page 33: Changing A Tyre

    04-5 Wheels and tyres 4.7 Changing a tyre • Remove the wheel mounting screws and lift off the tyre. • Place the spare tyre (not included in the scope of delivery) The car jack (not included in the scope of delivery) may on the wheel hub and align it.
  • Page 34 Wheels and tyres 04-6...

  • Page 35: Chapter 5: Exterior Structure

    05-1 Exterior Structure Chapter 5: Exterior Structure 5.1 Ventilation The following applies for ventilation: Ventilation is important if you want to feel comfortable in your van. No-draught ventilation has been integrated above the driving unit in your van. The roof lights ensure ventilation. Never interfere with the way in which they operate.
  • Page 36 Exterior Structure 05-2 Heating If the temperature outside is very high, we recommend that you park the vehicle in the shade to maintain the Power for the heating system is supplied from outside using cooling capacity. combustion air . At the same time, the exhaust air from the heating system is ducted outside.

  • Page 37: Opening And Closing Doors And Flaps

    Exterior Structure 05-3 5.2 Opening and closing doors and flaps Keys to the vehicle The following keys are supplied with the van: two keys to fit the following locks on the base vehicle: - driver‘s and passenger‘s doors - sliding door - rear doors - patrol flap - a code card.
  • Page 38 Exterior Structure 05-4 The window in the sliding door must always be closed before opening or closing the door. Ensure that neither people nor pets will be hurt when opening or closing the door. The sliding door must always be kept closed and locked while driving.

  • Page 39: Toilet Flap

    05-5 Exterior Structure Insect screen (plissé) Toilet flap • Carefully open and close the insect screen plissé by gui- Opening ding it along the guide rail. • Use key to unlock flap The insect screen plissé must be closed first before clo- •...
  • Page 40 Exterior Structure 05-6 Exterior gas supply Exterior socket The external gas socket is used to provide equipment Opening that requires gas, such as a gas barbecue or gas lamp, with • Take hold of the bottom of the cover flap and pull it gas outside the van.

  • Page 41: Fresh Water Filler Neck

    Exterior Structure 05-7 Fresh water filler neck Petrol filler neck Opening The black petrol cap is covered by a flap located on the left • Hold the flap by the latch and pull it up. side of the vehicle behind the driver's door in the lower sec- •...

  • Page 42: Bicycle Carrier

    Exterior Structure 05-8 5.3 Bicycle carrier • Ensure that the existing lighting equipment is not completely or partially obscured by any loads. The van’s handling when driving is significantly different when the bicycle carrier is in use. The driving speed should be adju- The maximum permissible loads for bicycle carriers are 35 kg.

  • Page 43: Sun Awning

    05-9 Exterior Structure Extending • Insert the hook on the crank into the grommet on the win- ding mechanism. • Hold the crank with one hand on the upper twist grip and the other on the lower twist grip. During the operating procedure gently pull the crank towards you and hold it as vertically in the grommet as possible.
  • Page 44 Exterior Structure 05-10 If the canvas is slack when extended, retract the awning until the canvas is tightly stretched again. Please refer also to the manufacturer's separate operating instructions.

  • Page 45: Chapter 6: Interior Structure

    06-1 Interior Structure Chapter 6: Interior Structure 6.1 Opening and closing doors and flaps Stowage and kitchen wall cabinets, kitchen drawers Opening • Press the pushbutton to unlock the flap/drawer. • Pull on the handle until the flap opens. Closing •...
  • Page 46 Interior Structure 06-2 Simple furniture doors Doors with push locks Opening Opening • Pull on the handle and swing the door open. • Depress the push lock until the knob pops out. • Pull gently on the handle and the door will open. Closing Closing •...
  • Page 47 Interior Structure 06-3 Fig. 2 Washroom door K60 T / K65 T Sliding doors Washroom cabinet Opening • Turn the knob to the left until the mechanism opens. Opening Then use the knob to carefully push the sliding door • Grasp the handle/frame of the sliding doors and push open along the guide rail.

  • Page 48: Television Holder For Flat-Screen Monitor

    Interior Structure 06-4 6.2 Television holder for flat-screen monitor Furniture doors with a locking mechanism Mirror cabinets, washroom • To unlock, push the metal rail to the left. The lock will be released and the TV mount can be folded out. Opening •...

  • Page 49: Worktop Extension For The Kitchen

    Interior Structure 06-5 6.4 Tables 6.3 Worktop extension for the kitchen Hinged table • Use one hand to bring the movable part to a horizontal position. The lower table top of the hinged table can be swung out. To • With the other hand, fold the lever by 90°...

  • Page 50: Bed Conversion

    Interior Structure 06-6 6.5 Bed conversion Emergency bed in the seating arrangement* The seating arrangement can be converted to an emergency bed. If the van has been fitted with a Milano seating bench*, the seating arrangement cannot be converted. Lowering/removing the table •...
  • Page 51 06-7 Interior Structure Rearranging the cushions K55 Rearranging the cushions K60(T) and K65(T) To convert To convert • Remove the table (see 6.4 Tables). • Hook the table into the lower guiding rail (see 6.4 Tables). • Pull the seating bench apart at the end towards the ent- rance (see 6.11 Seats in the superstructure).
  • Page 52 Interior Structure 06-8 Individual beds in the rear To convert beds • Distribute the two crossbeams evenly between the two bed frames to provide optimal support for the slatted frames. • Then place the two slatted frames on the crossbeams, ta- king care to ensure that the slanted side of the bed faces the front of the vehicle and the cushioning on the frame faces the centre of the vehicle.
  • Page 53 Interior Structure 06-9 • Finally, place the mattresses on the left and right, again • Place the extension board between the two slatted frames. taking note of the slant. There is a bar on the back of the extension board to ensu- If necessary, place the additional cushion for the ex- tension of the beds between the mattresses, making one...
  • Page 54 Interior Structure 06-10 Transversal bed in the rear To convert bed • First step: place the two slatted frames transversally to the vehicle on the base so that they are resting on the sup- porting shelves in the direction of the front of the vehicle, taking care to ensure that the cushioned sides of the frame are on the outer sides of the bed.
  • Page 55 Interior Structure 06-11 Climbing into the transversal bed in the rear • Then place the three mattresses lengthwise to the vehicle, • Climb into the transversal bed in the rear through the whereby the two mattresses with the slants are placed gap in the bulkhead partition, taking care to ensure that on the left and right by the rear doors.
  • Page 56 Interior Structure 06-12 Converting beds into storage space • Lash the mattresses and slatted frames with the fastening straps (for individual and transversal beds) • Place the fastening straps over the gap and insert them in the counterpart until they lock together. The bed can be fastened to the side wall to obtain additional storage space in the rear.

  • Page 57: Insert For Shower Tray

    Interior Structure 06-13 6.7 Windows 6.6 Insert for shower tray Knockout windows with locking hooks A removable insert has been placed in the shower try to protect it and make it easier to walk across it. Opening • Turn the latch by 90°.
  • Page 58 Interior Structure 06-14 • Turn the latch to the original position so that it clasps behind the brackets and pull the pane into the seal. Fully adjustable window stays Opening • Turn all latches by 90°. • Press the window latch outwards with your hand until it is open as far as you would like.
  • Page 59 Interior Structure 06-15 To combine • Pull the sunshade up slowly and evenly, then pull the insect screen down to the desired position. To avoid consequential damage, leave the shades open when the van is not in use. Sunshade/insect screen Sunshades and insect screens are integrated in the window from and fully adjustable.

  • Page 60: Dimming System For Driver's Cabin

    Interior Structure 06-16 6.8 Dimming system for driver's cabin Front system • Press the locks together to open the locking mechanism. • Pull the handles in the middle together slowly and The dimming shades may only be drawn when the vehicle is evenly.

  • Page 61: Skylight

    06-17 Interior Structure 6.11 Skylight Safety instructions • Never open the skylight in strong winds/rain/hail, etc. or if the temperature outside is below -20°C! • Do not use force to open the roof skylight when covered by ice or snow as this could break the hinges and opening mechanism.

  • Page 62: Seats In The Driver's Cabin

    Interior Structure 06-18 Insect screens and shades (plissés) Both plissés are fully adjustable by sliding them horizontally from side to side. 6.10 Seats in the driver's cabin All of the vans have pivoting driver's and passenger's seats, which can be used to extend the number of seats available in the superstructure.

  • Page 63: Construction Of The Seats

    06-19 Interior Structure 6.11 Construction of the seats The lever for turning the seat is located on the inner edge of the seats in the driver's cab. Cushion fastenings Swivelling seats • Put the armrests up. Seat cushions are held in place by an anti-slip mat. •...
  • Page 64 Interior Structure 06-20 Movable individual seats Widening the seating bench In place of the seating bench, the vehicle can be fitted with The seating bench can be widened by carefully pulling out movable individual seats. the movable part together with the cushion towards the sliding door until it goes no further.
  • Page 65 Interior Structure 06-21 The following conditions apply when using the seats • The seatbelt buckles must be positioned on the while driving: outside, next to the seats, and not led between the • Push both seats back to the rear position so that the backrest and the seat.

  • Page 66: Seatbelts In The Van

    Interior Structure 06-22 • The lower part of the seatbelt fits across your hips. Unbuckling the seatbelt • Press the button on the lock of the seatbelt to unlock the tongue. • Fasten seat belts before driving and keep them fastened while driving.

  • Page 67: Overview Of The Seating Arrangements

    Interior Structure 06-23 6.13 Overview of the seating arrangements K55 Vantana K60 Vantana Seats 1 - 4: may be used while driving. Seats 1 - 4: may be used while driving. K60 Milan Vantana K65 Milan Vantana Seats 1 - 4: may be used while driving. Seats 1 - 4: may be used while driving.
  • Page 68 Interior Structure 06-24 K65 Vantana Seats 1 - 4: may be used while driving.

  • Page 69: Chapter 7: Electrical Installations

    Electrical Installations Chapter 7: Electrical Installations 7.2 Elements of the electrical system 7.1 Safety instructions Advice and instructions The installation of electrical devices in HOBBY's vans has Important been carried out in accordance with the valid regulations • Any changes to the electrical installations may only be carried out by a professional electrician.
  • Page 70 Electrical Installations 07-2 230V automatic circuit breaker with an earth leakage • Unclamp the battery circuit breaker if the ancillary battery circuit breaker is not being used for a long period of time (more than 1-2 months). Even if the battery circuit breaker is interrupted, The 230V automatic circuit breaker supplies and protects the the battery can still be charged by the battery charger (con- 230V devices. servation charging). • To switch off the 230V power supply in the entire system, • Should the consumer battery be removed, isolate the plus set the 230V automatic circuit breaker to “0” (OFF). pole (to prevent short circuits when turning on the motor). Fuses • Only replace defective fuses after the cause of the defect Battery charger has been remedied by a professional electrician. • The charger’s capacity is 360 W. • The new fuse must have the same amperage as the old • The charger functions in accordance with IU0U1 charging one. technology. • In the case of misuse the guarantee and manufacturer’s liability will no longer apply.
  • Page 71 07-3 Electrical Installations Controlpanel • If there should be a power failure, the system will remem- ber whether the main switch was on or off. As soon as the power is back on, the main switch will automatically switch itself back on. With the exception of the heating, all of the electrical devices that continuously use current will then begin to operate again. In this case, the heating system will indicate a malfunction. If the vehicle's motor is running, the refrigerator will operate automatically on 12V, i.e. it is not necessary to press the main switch. In this case, the selector switch for the refrigerator must be set to 12V operation. All other 12V electrical devices will only operate on the ancillary battery if the main switch has Functions of the main switch been activated. • After initially connecting the van to the 230 V mains, you must Wall light in the press either the main switch in order to activate all of the Ceiling Lamp seating arrangement 12 V electrical devices and the 230 V electrical devices that are switched by the system (Combi 6 E , air-conditioning...
  • Page 72 Electrical Installations 07-4 This function is only available if the vehicle has been fitted The ceiling light can also be switched on directly on the lamp. The lamp must be activated before you can use the with the light package. control panel to switch it on and off. Worktop lighting Key Memory • Briefly press the key to switch the worktop lighting in the • This key is used to save and recall the state of individual kitchen on and off. lights. Press briefly on this key to recall the last saved state of all switchable 12 V lights. Press longer on this key to Lighting atmosphere 1 save the lighting state of a lamp. This key is not used to save the state of the 230 V electrical devices (e.g. hot-air • 1: Switches all indirect lighting in the wall cabinets on and heating). off. T models: Only switches the indirect lighting in the wall Entrance light (outer tent light) cabinets in the rear on and off.
  • Page 73 Electrical Installations 07-5 Radio switch • Briefly press the key to switch the radio on and off. Filling level indicator • Briefly press the key to display the graph that shows you the level of the fresh and waste water tanks. LCD display All of the vehicles are equipped with a program for mea- Basic menu suring illumination. This program only runs if the power is The basic menu appears if you have not pressed a navigation connected; if previously activated, it is saved after a reset. All of the lights will be switched on. If a key is now pressed, key during the past 30 seconds (approximately). This menu is the corresponding light will be switched on. After approx. not illuminated. The time, date and alarm clock function are 1 minu7te, all of the other lights will also be switched on set in this menu. provided no other key is pressed. Main display To switch on: Press Illuminated Wall Cabinets, Ceiling Rotary switch Lamp, Kitchen light somewhat longer. Turn the switch to select a menu. Press it to shift to a To switch off: Press Illuminated Wall Cabinets, Ceiling Lamp and lighting atmosphere 1 somewhat submenu, in which you can enter changes.
  • Page 74 Electrical Installations 07-6 Date display The current date is displayed in this field. Alarm clock This icon is use to activate the alarm clock. The example shows the alarm clock when it has been deactivated. When it is activated, there is no line through the icon. Charging status of the ancillary battery If the arrow points towards the battery, it will be charged. If the arrow points away from the battery, it will be discharged. Main switch The icon for the main switch always appears when the Level of the tank system's 12V main switch has been switched on. • After turning once to the right or left, the menu for displa- Mains connection ying the level of the fresh and waste water tanks appears. This icon appears if the van is connected to the 230V mains. Generator/Motor is running Align the vehicle horizontally to obtain a meaningful result An icon will appear here if the van's motor has been from the filling level indicator.
  • Page 75 Electrical Installations 07-7 Temperature 12V Outside temperature • If your vehicle has a 12V connection, the temperature will • After once again turning to the right, the menu for displa- be displayed. Inside temperature (above) and outside tem- ying the outside temperature appears. The outside tem- perature (below). perature sensor is located underneath the vehicle near the • The display is shown in increments of 0.5° C. entrance step.
  • Page 76 Electrical Installations 07-8 Calibrating the temperature Inside temperature It is possible to calibrate the indoor and outdoor temperatures • After once again turning to the right, the menu for displa- shown, as temperature effects on the sensors may lead to a ying the inside temperature appears. deviation between the temperature displayed and the actual • The display is shown in increments of 0.5° C. temperature. • To calibrate the displayed temperatures, please switch to the temperature display. It is irrelevant whether the indoor or the outdoor temperature is displayed. • Press the rotary/selector switch for several seconds. The system will now switch automatically to calibration mode. • Switch to the desired area (indoor or outdoor) by turning the selector switch. Press briefly on the switch to select the area.
  • Page 77 07-9 Electrical Installations • You can now increase or decrease the temperature shown by up to +/-7°C in steps of 1°C. When the desired value has been set, quit the menu item by pressing briefly on the selector switch. • Quit the calibration menu by using the selector switch to select the Return icon. The changed value is now shown on the temperature display. Battery charging After the type and capacity of the battery have been set and it has been calibrated, the battery sensor permanently monitors the status of the batteries (starter/ancillary battery). The intelligent battery sensor is connected directly to the nega- tive terminal on the ancillary battery. Battery charging function 230V voltage applied and charger has been activated for sensor control.
  • Page 78 Electrical Installations 07-10 Ancillary battery Starter battery Setting the battery type These menus show The type and capacity of the battery have been set by the - the charging voltage (U) manufacturer. If the type of battery is changed, these settings - the charging current (I) must be adjusted accordingly. - the remaining time until discharge, dependent on the cap city and the actual flow (current) To reach this part of the menu, go to the "Loading the Batte- - as well as the charging status of the batteries (1/2 or 2/3). ry" menu and press the button for approx. 2 seconds.
  • Page 79 07-11 Electrical Installations Hot-air heating (only Fiat Drive) Air conditioning Turn the rotary switch to access the heating menu. This is The following functions for the air-conditioning where you can set the hot water temperature as well as the system can be set on the control unit: temperature desired inside the van (see also Chapter 10.2). - On/Off - Cool Mode: cooling and ventilation Cool Low / Cool / Cool High - Fan Mode: ventilation only Fan Low / Fan High - Dry: heating function The aforementioned functions are only available for air conditioning systems that are CI bus compatible.
  • Page 80 Electrical Installations 07-12 Setting the time, alarm clock and date • After pressing the menu button for a longer period of time (approx. 2 seconds) the menu for setting the current time, date, wake-up time and activating or deactivating the alarm clock appears. • Within the menu's you move left or right by turning to the various setting value.
  • Page 81 07-13 Electrical Installations WLAN module* Hobby's CI-Bus board management can link together up to 15 devices, enabling you to operate them using just one central control panel that shows their functions on its display. (standard) Turn the rotary encoder to access the WLAN menu. Power is When coupled to a WLAN module, all of the functions on the supplied via the battery and/or via the 230V mains connection. LCD control panel can be wirelessly controlled via your smart- The WLAN is ready as soon as “WLAN: On” appears after the phone, tablet or notebook. module has been switched on. After the main switch on the control panel has been switched on and all of the connections have been correctly attached, a WLAN network is set up that is recognized by all WLAN- enabled devices. The SD card is also found on the WLAN module. The devices are updated on this card. This SD card cannot be written in Windows file format.
  • Page 82 Electrical Installations 07-14 Press the rotary encoder key to access the submenu in which Then select the network, enter the password and click on the the connection data for the WLAN network is displayed. (The “Connect” button to confirm. You can now call up the website menu on the left only shows example data.) http://192.168.0.1 in the Internet browser. The WLAN-enabled device must be connected to the net- By continuing to turn and confirm the rotary encoder on the work and the password must be confirmed: under Settings, control panel, you will reach the Web server data, which is go to “WLAN” and select the network “meinhobby1” (in required to open the data in the Web browser. this example). Should this not be displayed immediately, you must first use the search/scan function.
  • Page 83 07-15 Electrical Installations Settings can be called up and changed in the browser on The name of the network and the password can be changed page 192.168.0.1/cfg.php: here. This also applies for the Web Interface Settings. At pre- sent, the UMTS and No-IP settings are not yet supported; they Click on the „Get“ button to call up the set values. have only been integrated for future applications. After making any changes, the changed values must be saved by clicking on the „Set“ button. These changes will take effect after approx. 2 minutes.
  • Page 84 Electrical Installations 07-16 At present, operation via a surfstick is not yet supported. Please use the WLAN menu in the LCD display to switch WLAN operation on and off. After switching it off, “WLAN shutdown” will be displayed for approx. 60 seconds. When “WLAN: Off” is displayed, the vehicle's entire power supply can be switched off. General information regarding the LCD display The SD card may be damaged if the van's power supply The time and date are buffered by a 3V 210 mAh, CR2032 is disconnected (from the mains or the battery) without having shut down the WLAN correctly. type button cell. If, therefore, the time should be incorrect or the clock should stop working, this button cell must be replaced. It is mounted on the reverse of the circuit board of the LCD display. To replace this button cell, the LCD display must be removed from the furniture front by carefully clipping the chrome-plated frame out of its holder. You will then see the screws that fasten the plastic part to the furniture. Loosen these screws to detach the display. When replacing the button cell, please ensure that plus and minus are in the right direction. Incorrect polarity may cause the display to become defect.
  • Page 85 07-17 Electrical Installations Remote control(s), bed Remote control, washroom (only T models) • Briefly press the key on the remote control by the bed to • Briefly press the key to switch on the light in the washroom switch on the left light and the right light . The key (and in the separate shower, if there is one). switches the ceiling light above the seating arrange- ment on and off. Press longer on the key to regulate how brightly you want the lights to shine. The brightness you set will be saved; when the lights are switched on again, the brightness you originally set will also be switched on again.
  • Page 86 Electrical Installations 07-18 Remote control for kitchen Remote control, entrance • Briefly press the left key to switch on the bathroom light. These remote control functions work even if the LCD panel • In the T models, the left key is used to switch indirect lighting has been switched off. The remote control controls the elec- in the wall cabinets in the rear on and off. tric entrance step. • Briefly press the right key to switch on the worktop light in the kitchen. • Press the key to fold the step out; press it again to fold the step back in. • Briefly press the key to switch on the entrance light/ outer tent light (not while the motor is running and only if equipped with the light package). • Briefly press the key to switch on the ceiling light (provi- ded it has been activated via the switch on the light).

  • Page 87: Electric Power Supply

    07-19 Electrical Installations 7.3 Electric power supply In all of the vehicles, the central electrical system is installed underneath the passenger seat. Electricity for the van can be obtained from the following connections: - 230V mains connection 50 Hz - via the ancillary battery Everything that uses 12 V, such as lighting, water supply, etc., is available. Supply via mains connection The van is connected to the external 230V mains by a CEE feeder plug located in the side wall. To connect the CEE feeder plug • Switch off the automatic circuit breaker (p. 07-20) by pressing the rocker switch...
  • Page 88 Electrical Installations 07-20 To disconnect the electric connection: • Switch off the automatic circuit breaker by pressing the rocker switch down • Remove the CEE plug • Press the cover flap (p. 07-19) of the external socket down until it clicks into place. Only plugs and cords that comply with CEE standards may be used. Fuse protection for the 230V system The 230V system is protected by a two-pole 13 A automatic circuit breaker , which is located in the seat chest in the seating arrangement. It can be accessed via the side com- partment.
  • Page 89 07-21 Electrical Installations Rules for the mains connection • Use only a 3 x 2.5 mm cable with a maximum length of 25 m, a CEE plug and connector to connect the van to an external 230 V mains. • After the mains connection has been plugged in, both the modular and the vehicle battery will automatically be char- ged by the battery charger in the van (even if the Control Panel has not been switched on). When obtaining electricity via a cable drum, this must be completely unwound, as otherwise induction may cause the cable to heat up, which could lead to burning. Residual current device (Provided there is no protection against overheating) The standard version of your vehicle is equipped with a residual current device that will interrupt the electric circuit in • The 230 V mains connection in the van has been designed case of a possible residual current. Should there be a mal- for a total power consumption of 3000 W. If additional function, the passenger circuit breaker opens the entire devices requiring electricity are connected, such as a water 230 V circuit.
  • Page 90 Electrical Installations 07-22 - If the automatic circuit breaker goes off abruptly again, there is The tripping time for the residual current device (RCD) either a short circuit or an earth fault. with a residual current of 30 mA is less than 0.1 seconds. After putting the electric system into operation, the function of Devices that set off during operation show that there is a the residual current device must be checked. After voltage has defect; they must be checked and/or repaired by an electrical been applied to the switch and it is on (set to I-ON) it must engineering specialist. set off when you press the test button Switching it back on again and again will do no good. The The rocker switch (p. 07-20) jumps down; after it has automatic circuit breaker also goes off when the rocker successfully been checked it must be switched back up to the switch is held firmly in place. "On" setting. This check should be carried out at least once a month to en- sure that the residual current device functions perfectly in case there should be a fault in the current. When the residual current device has been set off (even when testing) the customised settings in all mains-operated devices are lost and the default settings made by the ma- nufacturer will apply again.
  • Page 91 07-23 Electrical Installations • Only accumulator batteries with bound electrolytes (gel batteries) may be installed in those positions specified by the manufacturer. • The installed gel battery may not be opened. • When changing ancillary batteries, use only batteries of the same make and capacity. • All of the electrical devices must be switched off be- fore you disconnect or connect the ancillary battery. • Before replacing fuses you must first de-energise the charger. • Before replacing fuses you must first de-energise the charge controller. • Before replacing a blown fuse you must first fix whate- ver caused the fuse to blow. Operation via ancillary battery • Fuses may only be replaced by fuses with the same fuse protection value. Position of the 92 Ah/95 Ah AGM ancillary battery • Airing the charge controller insufficiently will cause a (model-specific) reduction of the charge current.
  • Page 92 Electrical Installations 07-24 The battery charger is directly connected to the ancillary bat- tery so that the ancillary and starter batteries can be charged even if the battery circuit breaker is switched on. To keep the batteries charged even when not in use, it is mandatory that the vehicle be connected to a 230V mains connection every 6 weeks. Recharging should be carried out for at least 24 hours. The battery circuit breaker must be on when using the vehicle home and whilst driving. Position of the battery circuit breaker When the circuit breaker is open, the electrical input stage will not engage automatically.
  • Page 93 Electrical Installations 07-25 Operating and charging the ancillary battery • Always charge the ancillary battery for at least 10 hours before each journey, directly after each journey and before you take the van temporarily out of service. If the van is not connected to the 230V mains supply, the • Use every opportunity during your journey to charge ancillary battery will supply the electrical system with 12V the battery. DC voltage. Since the battery only has a limited capacity, the • The battery loses its capacity after having been used electrical devices should not be operated for a longer period for a while and at low temperatures. of time without charging the battery or connecting the cam- • An acoustic warning signal will be given off if the remai- per to the 230 V mains connection. ning time during discharge operation is less than 1 hour. • A warning will go off if the battery ages to a value less The ancillary battery can be charged from the following po- than 50% of its nominal capacity. wer sources: • The battery is only charged if it has a minimum voltage of 8 V. - the generator when the motor is running • If the vehicle is not in use for a longer period of time, the batte- - the CA 360 charger ry should be disconnected after it has been optimally charged (only via 230 V power feed) by switching the battery circuit breaker on.
  • Page 94 Electrical Installations 07-26 Charger CA-360, 25 A power charging module Socket; the middle pin is the sensor. PCB switches. The switches must all be in the top posi- The charger supplies the batteries with electric power when tion, i.e. all set to “off”. there is bus-powered mains operation. Changeover contact, for free disposal. Contact bridge, fan on/off. As they heat up, the charger reduces its power output to LED blinks to show current charging mode. ensure that there is no chance of overheating. The charging device can be accessed from the back of the passenger seat.
  • Page 95 07-27 Electrical Installations Operation when the motor is running The voltage of the van battery must rise if - the engine speed is above the idling speed, - the vehicle‘s battery is not completely discharged. As soon as the motor is running, a relay connects the starter battery and the van battery in parallel. Therefore, the dynamo charges both batteries. If the D+ signal no longer sits close to The control panel shows whether or not the generator has the dynamo, the two batteries will be separated from each other been charged. If this is not the case, please check the following: again. In this way, the starter battery cannot be discharged by equipment in the van. • Is the 50A fuse in the supply line to the ancillary battery near the motor battery functioning properly? The 12 V supply for the refrigerator only functions when you • Is the “Motor running” signal on the input module on? are driving. If the motor has stopped, the 12 V operation of the refrigerator is automatically turned off again. To charge a discharged van battery optimally while driving, disconnect the 12 V operation of the refrigerator and turn off as much equipment as possible that uses 12 V. Checklist • Turn off the motor. • Switch on the 12 V master switch. • Turn off all equipment that uses 12 V. • Start the motor.

  • Page 96: Electrical System

    Electrical Installations 07-28 7.4 Electrical system As soon as there is a mains connection, the electrical system will switch from battery operation to mains operation. All of the lamps in the van use 12V LED lights. Only large electrical devices such as the Combi E heating air-conditioning system, etc., use 230V. Assignment of fuses, Input module The fuses for the individual internal electric circuits are loca- ted in the input module. In some models, there may be slight deviations in this assignment. Only replace defect fuses if you know what caused the fuse to blow and have fixed this.
  • Page 97 07-29 Electrical Installations TV unit The installation area for the flat-screen TV is located above the seating arrangement on the partition to the bathroom. The corresponding connections are located in the adjacent wall cabinet. The corresponding connection for the SAT antenna (E3) is positioned behind the furniture surround on which the TV connections are located. Light Control System The outputs are safeguarded by internal circuit breakers (polyswitch fuses).

  • Page 98: Special Lights

    Electrical Installations 07-30 External socket and antenna terminal in the 7.5 Special Lights outer tent The switches for the lights described here are located directly As an option, your van also has a combined external socket on the lights themselves; they are not controlled via the and antenna terminal in the outer tent. This can be used, for control panel. example, to set up a TV in the outer tent. Depending on how you wire it, the integrated antenna terminal can be used as either an input or an output socket. For further information, please speak to your Hobby dealer...

  • Page 99: Mobile Navigation

    07-31 Electrical Installations Fig. 1 Fig. 2 Entrance light 7.6 Mobile navigation As an optional feature, your van can be equipped with a mo- The entrance area by the sliding door has been fitted with a bile navigation system and integrated rear view camera. light that cannot be operated using the control panel or one of the remote controls. Toggle the light in the frame: • R ead the device manufacturer‘s operating instructions carefully before initial operation. - to the right = off (see Fig. 1) = light permanently on (see Fig. 2) - centre - to the left = light switches on automatically when sliding • Do not allow yourself to be distracted by this device as this may cause accidents. door is opened. • Never operate the device while driving. • Check the display panel only when the traffic situation is safe for doing so.

  • Page 100: Subsequently Installed Devices

    Electrical Installations 07-32 7.7 Subsequently installed devices Subsequently installed electronic devices that can be used while driving (e.g. mobile phones, wireless equipment, radios, came- ras for driving in reverse, navigation equipment, or others) must meet all of the requirements for electromagnetic compatibility. Such equipment must have been approved in accordance with EU Guideline 72/245/EWG as it appears in version 95/54/EG, because otherwise it may cause interference with the electronic systems already installed in the van. A CE mark is mandatory for devices that have been subsequently installed and which cannot be used while driving.

  • Page 101: Chapter 8: Water

    08-1 Water Chapter 8: Water 8.1 General We recommend that you inspect any water you have left in the tank, this is very critical before using the water again. • Always use water that is of drinkable quality when wor- king with food. This also applies for washing your hands or objects that come into contact with food. 8.2 Water supply • In order to ensure excellent water quality, water should be taken directly from the public drinking water system. Function of the water supply • Garden hoses, watering cans and similar materials unsu- Fresh water is supplied to the hot-air heating system, the itable for drinking water should never be used to fill the kitchen and toilette via a submersible pump. The TANDEM mobile system. • If the van has not been used for a longer period of time, submersible pump operates electrically: the entire water system must be emptied completely. - via the starter / ancillary battery, • After longer periods of stagnation, the water system - when the van is connected to the 230V mains via the must be flushed thoroughly before being used. Should power supply. you discover impurities, the material should be disin- fected using suitable agents that have been approved for such measures.
  • Page 102 Water 08-2 The following applies for the TANDEM submersible pump: • The TANDEM submersible pump is only suitable for water. • The TANDEM submersible pump can briefly tolerate tem- peratures of up to 60º C. • Avoid dry runs. • Protect the pump from freezing. • Hard blows or hits as well as very dirty water can destroy the pump. The TANDEM submersible pump requires no maintenance. Fresh water tank The TANDEM submersible pump switches itself on automati- cally when the water taps are opened. The tank has a volume of 90 l and is located in the rear. The tank is filled with fresh water by means of the filler neck on the side wall. The neck for filling up fresh water is marked by a blue cap and a picture of a water tap on the upper edge of the frame. Use the enclosed key for the external flap locks to open or close the cap on the neck.
  • Page 103 08-3 Water If you fill too much water into the tank, the excess will run out Use the control panel to check the amount of water in the through an automatic overflow on the opening underneath the fresh water tank. vehicle and possibly also from the filler neck. Never introduce anti-freeze or other chemicals into the Check the red service lids regularly; they may become loose if water system. the fresh water tank is filled often. This can be poisonous! When operating during winter ensure that the fresh water Filling the water system tank is sufficiently heated. • Place the van in a horizontal position. • Shut all of the water taps. To remove water • Switch on the main switch on the control panel. • The water will be mixed to the desired temperature • Close the outlet valve (FrostControl) on the boiler. according to the position of the pre-mixing unit. • Unlock the petrol cap and turn it counter-clockwise to open it. • Fill the water tank using the fresh water filler neck. • Turn all of the water taps to „hot“ and open them. The water pump will be switched on. • Leave the water taps open until the water flows out of the taps without any bubbles. This is the only way to ensure that the boiler will also be filled with water. • Turn all of the taps to „cold“ and leave them open. The cold water pipes will be filled with water. • Leave the water taps open until the water flows out of the fixtures without any bubbles. • Shut all of the water taps.

  • Page 104: Hot Water Supply

    Water 08-4 Hot water supply Hot water is supplied by means of the hot-air heating system with its integrated hot-water boiler (see also Chapter 10.2); the options for settings are described on p. 10-05 “Changing the hot water temperature”. The boiler will automatically empty itself via a safety or outlet valve if there is danger of frost (see also 10-13 Frost Control). Position of the Frost Control valve The Frost Control valve is always located directly by the model-specific place of installation for the hot-air heating system. The non-electric safety or drain valve will automatically open at temperatures under approx. 3°C and drain the boiler contents via a drain nozzle. If the cold water system is operated without the boiler the boiler tank will still fill with water. In order to avoid frost damage the boiler must be drained via the drain valve, even when not in use.
  • Page 105 08-5 Water Emptying the fresh water tank Emptying the waste water tank • The waste water opening is located on the left side under- The outlet valve is located in the rear behind an opening in neath the vehicle. the furniture, directly on the fresh water tank. • Turn the opening to open it and drain off the waste water. • After all of the waste water has been drained off, shut the • To empty the fresh water tank, turn the rotating wheel to opening by turning it. the left to open. Always empty the fresh water tank completely if the hea- ting has not been switched on and the van is not in use, and especially if there is frost.
  • Page 106 Water 08-6 Emptying the entire water system If the vehicle is not being used and there is a danger of • Use the control panel to switch off the electricity for the sub-zero temperatures be sure to drain the entire water water pump by pressing the main switch for a longer period system. Leave taps turn on in the middle position. Leave all drain valves open. of time (4 sec.). • Open all of the water taps to the centre setting. Only empty your waste water tank at the specially desi- • Hang up the adjustable shower head in the shower. gnated disposal points and never in open spaces! As a • Open all of the outlet valves (including the FrostControl). rule disposal points can be found at motorway service • Unscrew the cap on the cleaning port of the fresh water stations; campsites and petrol stations. tank • Unscrew the overflow pipe in the fresh water tank. • Remove the lid of the water tank. Take out the water pump and hold it up until the water pipes have emptied com- pletely. • Check whether the tank, boiler, faucets and pipes have emptied completely. If necessary, blow out any remaining water in the pipes using compressed air (max. 0.5 bar). • Re-insert the the water pump in the fresh water tank and close the openings. • Leave the faucets and the outlet valves open. • Clean the tanks and rinse them thoroughly. • Allow the water system to dry for as long as possible. • Do not forget to empty the toilet cassette.

  • Page 107: Flushing Toilet

    Water 08-7 Waste water tank The waste water tank is integrated in the chassis; it is insulated. Optional: After the heating system has been switched on on the control panel, the hot air is conducted to the waste water tank. This prevents the waste water from freezing in a light frost. Do a small quantity of antifreeze agent (e.g. table salt) to the waste water tank if temperatures are significantly below freezing to prevent the waste water from freezing. 8.3 Flushing toilet The waste water tank is not sufficiently protected against damage from frost when the vehicle is not in use. Preparing the toilet Therefore, if there is any danger of sub-zero temperatures • Open the Thetford door (see 5.1) and pull the holding bar empty the waste water tank completely. up to remove the waste tank. Never pour boiling water down the sink. This can cause The waste tank can only be removed when the drain distortions and leaks in the waste water system. valve is closed. Use the control panel to check the amount of water in the • Pull out the tank as far as possible, keeping it level. waste water tank. • Slightly tip the waste tank and then pull it out completely. • Place it in an upright vertical position. • Turn the drain nozzle to an upward position.
  • Page 108 Water 08-8 Use toilet fluids very sparingly. An overdose is no guaran- Never fill toilet fluids directly into the toilet bowl. tee of preventing possible odours! • Push the waste tank back into position. • Fill the waste tank with the correct amount of toilet fluids. • Ensure that the holding bar secures the waste tank. • Then add enough water to completely cover the bottom of • Close the service flap. the waste tank. • Return the drain nozzle to its original position.
  • Page 109 Water 08-9 Using the toilet Emptying the waste tank The waste tank must be emptied at the latest when the LED • Turn the toilet bowl to a comfortable position. lights up. It is recommended that the tank is emptied before • Fill the toilet bowl with a small amount of water by pres- this. The LED lights up when the tank contains more than 15 sing the flush button or by opening the drain valve by litres. From this point in time the tank has a residual capacity pulling the valve handle under the toilet bowl towards you. of 2 litres, representing approx. 5 flushes. • Use the toilet. • After use open the drain valve (if still closed) and flush. • Open the toilet flap and pull the holding bar up to remove Close the drain valve after flushing. the waste tank. The waste tank can only be removed when the drain valve is closed.
  • Page 110 Water 08-10 Only empty the waste tank at specially designated dis- posal points and never in open spaces! • Take the waste tank to a designated disposal site, making sure to hold the drain nozzle in an upright position. • Remove the cap on the drain nozzle. • Tilt the waste tank so that the drain nozzle is pointing downwards. • Press the vent button with your thumb and hold it down. The waste tank will drain itself. • Return the waste tank to its storage position, ensuring that it is pushed in until the holding bar locks into place. • Lock the service flap.

  • Page 111: Chapter 9: Gas

    09-1 Chapter 9: Gas • The connecting hose should also be checked regularly for damage. Replace it immediately if you find tears, porous spots or similar damage. 9.1 General safety rules when using LPG • The operator is responsible for having checks carried out. fittings This also applies for vehicles that have not been approved for driving on the road.
  • Page 112 09-2 Regulators and valves • Use only special vehicle regulators that have a safety valve. In accordance with the German DVWG (German Associa- tion of the Gas and Water Sector) Worksheet G 607, other regulators are not permitted; they are not adequate for handling the heavy strain.

  • Page 113: Gas Supply

    09-3 Before initial operation • The waste gas pipe must be tightly connected to the hea- ting and chimney without any leaks. It may not be dama- ged. • Keep vents clear. • Remove any snow from the chimney. • Clear aspirating openings for combustion air in the side all from dirt and/or snow.
  • Page 114 09-4 The following applies to the gas bottle cabinet: • Always check the gas cylinder mountings before driving. Stand the gas cylinders upright and close the valves. • Pull any loose straps tight. • The (high-pressure) hose to the cylinders must be che- cked for leaks using the leak detector every time a cylin- der is changed.
  • Page 115 09-5 Changing gas cylinders Do not smoke or ignite open flames while changing the gas cylinders. After changing the gas bottles, check whether there is any gas escaping from the tie-in point by spraying it with leak detection spray. • Open the door of the gas bottle cabinet. •...
  • Page 116 09-6 Gas regulator with a crash sensor The following applies to stop valves and valves: • All the valves on gas devices must be closed while driving. Using the MonoControl CS respectively DuoControl CS, it is • To open the valves: turn them towards the gas line, i.e. in possible to heat the vehicle even while driving.
  • Page 117 09-7   DuoCo mfort Switching valve for the two-cylinder gas unit To operate The DuoControl CS changeover valve enables you to automa- Open the valve on the bottle. tically change from the operating bottle to the spare one. The Press firmly on the hose rupture protection (green button) on the high-pressure hose.
  • Page 118 09-8 a Turn the knob to the left or right to determine which DuoC cylinder is to be used. b Shows the status of the cylinder in use. Green: full Red: empty Function • Attach gas cylinders and open the valves of both gas cylin- ders.
  • Page 119 09-9 The coupling valve has been constructed in such a way that the emergency shutoff valve can only be opened if a plug con- nection has been used to hitch the coupling. When hitching, the plug connection is plugged into the safety coupling. When unhitched, use the protective cap to shut the opening of the valve.
  • Page 120 09-10...

  • Page 121: Chapter 10: Built-In Devices

    10-1 Built-in devices Chapter 10: Built-in devices 10.1 General Information In this chapter, you will find information on the devices that have been built into the van. This information refers only to the operation of these devices. To some extent, the devices described are special accessories.
  • Page 122 Built-in devices 10-2 Initial operation • Set the air vents in the van so that the warm air is blown out where required. • Check that the chimney is clear. Remove any covers. • Open the gas bottle and gas shutoff valve on the gas pipe. •...
  • Page 123 Built-in devices 10-3 To operate Adjusting knob / pushbutton The adjusting knob / pushbutton is used to select and change specified values and parameters. The changes are sa- Start / stand-by screen ved by briefly pressing the button. Selected menu items blink. A few seconds after the control panel has been connected to the Turn to the right (+)
  • Page 124 Built-in devices 10-4 Changing the room temperature Switching the control panel on and off Use the adjusting knob / pushbutton to select the icon in the Press the adjusting knob / pushbutton menu line for longer than 3 seconds. - Press to switch to the setting mode. - Previously set values / operating parame- - Use the adjusting knob / pushbutton to select the desired temperature.
  • Page 125 10-5 Built-in devices Changing the hot water temperature Selecting the type of energy Use the adjusting knob / pushbutton to select the icon in the Use the adjusting knob / pushbutton to select the icon in the menu line menu line - Press to switch to the setting mode.
  • Page 126 Built-in devices 10-6 Selecting the fan speed As soon as the heating has been switched on (room tempe- rature and hot water temperature have been activated) the Use the adjusting knob / pushbutton to select the icon in the type of energy selected in the previous heating operation is menu line displayed in the status line.
  • Page 127 Built-in devices 10-7 Setting the timer BOOST To heat room rapidly Available if the difference between the selected and the actual room tempera- The timer can only be selected if the clock on the control panel has been set. ture is more than 10°C. If the timer has been activated (ON), the menu item Activate timer (OFF) is first displayed.
  • Page 128 Built-in devices 10-8 Selecting the type of energy If the start/end time was exceeded during entry, the operating parameters will only be taken into account after the next start/ - Use the adjusting knob / pushbut- end time has been reached. Until then, the operating parameters ton to select the desired type of set outside the timer will remain valid.
  • Page 129 Built-in devices 10-9 Activating the timer (ON) Setting the time - The hours blink. - Use the adjusting knob / pushbut- - Use the adjusting knob / push- ton to activate the timer (ON). button to set the hours (24-hour - Press the adjusting knob / push- mode).
  • Page 130 Built-in devices 10-10 Changing the background illumination of the control panel Resetting to manufacturer's default setting (RESET) The reset function resets the control The background illumination can be panel to the manufacturer's default changed in 10 increments. setting. It deletes all of the settings you have made.
  • Page 131 10-11 Built-in devices Warning Reading out the warning code - Use the adjusting knob / pushbut- A warning icon appears to signal a warning that one of the ope- ton to select the icon. rating parameters has reached an undefined status. In this case, - Press the adjusting knob / push- the device in question will continue to operate.
  • Page 132 Built-in devices 10-12 Malfunction Maintenance If there is a malfunction, the control panel will immediately go to This device requires no maintenance. Use a non-abrasive cloth “Malfunction” mode and display the Malfunction error code. dampened with water to clean the front. If this is not sufficient, use a neutral soap solution.
  • Page 133 Built-in devices 10-13 FrostControl To activate • Push in the knob at position (m) slightly and, at the same FrostControl is a non-electric safety or drain valve. If there time, move it 90° towards position (k). is a risk of sub-zero temperatures it automatically drains the •...

  • Page 134: Refrigerator

    Built-in devices 10-14 10.3 Refrigerator Refrigerator door lock Refrigerators made by Dometic will be installed. While driving, the refrigerator door must always be closed and locked. If the external temperature is high, full refrigerating capa- city can only be ensured by means of sufficient ventilation. Opening If necessary, to achieve better ventilation, the refrigerator’s •...
  • Page 135 Built-in devices 10-15 • The refrigerator runs without a thermostatic control (con- tinuous operation). 12 V operation should, therefore, only serve to maintain a temperature which has already been achieved. • To turn the refrigerator off turn the energy selector switch to the O position 230 V operation •...

  • Page 136: Storing Food

    Built-in devices 10-16 • Use the thermostat to regulate the cooling capacity. The freezer compartment is suitable for making ice cubes No absolute temperature values have been assigned to or for storing frozen food for a short period of time. It is not the temperature levels.
  • Page 137 Built-in devices 10-17 If not in use for a longer period of time, the refrigerator should Compressor refrigerator (K55 only) be switched to the ventilation position to prevent bad odours. Bei dem Modell K55 sind abweichend von den vorherigen To activate the ventilation position, turn the lock to the Contrary to the previous descriptions, the following applies for ventilation position (see illustration).
  • Page 138 Built-in devices 10-18 Operation The refrigerator runs on 12V or a mains connection. To switch on • Switch the refrigerator on by turning the temperature regula- to the right (green control light is activated). Use the temperature regulator to set the temperature as desired. The integrated thermostat regulates the temperature as follows: 1 = lowest cooling capacity 7 = highest cooling capacity...

  • Page 139: Gas Cooker

    Built-in devices 10-19 • The sockets above the cooker may not be used when cooking. Shut the protective caps. Never use the cooker or other devices extracting combu- stion air from the interior of the vehicle to heat the vehicle. If this is ignored there is an acute risk to life due to a lack of oxygen and the odourless carbon monoxide which could be generated.
  • Page 140 Built-in devices 10-20 • Release the rotary switch and turn to the desired set- ting (large or small flame). • If ignition was unsuccessful, repeat the procedure. • To turn off the gas flame, turn the rotary switch back to the “0” position •...

  • Page 141: Rooftop Air Conditioning

    Built-in devices 10-21 10.5 Rooftop Air Conditioning To set the direction of ventilation The air supply within the vehicle can be regulated by setting The air conditioner is located instead of the roof window on the air nozzles. the living room ceiling. To operate the air conditioner correctly and optimize its per- formance, you should observe the following: •...
  • Page 142 Built-in devices 10-22...

  • Page 143: Chapter 11: Accessories

    • Any changes to the status of the van as set by the manufacturer may endanger the driving performance and roadworthiness of your vehicle. • Any accessories, add-ons, modifications or mounted parts that have not been approved by HOBBY may cause damage to the vehicle and impair its roadworthiness. Even if an expertise, general type approval or design approval has been provided for these parts, this does not ensure the orderly condition of the product.
  • Page 144 Accessories 11-2 Object Weight[kg] Object Weight[kg] Base vehicle/Chassis REMIS plissé folding system Air-conditioning in the driver's cab, automatic 18.00 for front and side windows in driver's cab 3.50 Bumpers, front, painted colour of vehicle 2.00 Superstructure Comfort-Matic (automatic transmission) 17.00 Bicycle carrier for 2 bicycles Vantana 9.50 Cruise control 0.20 Diesel tank, 120 litres instead of 90 litres 28.00 Insect screen plissé for sliding door 4.00 Electric wing mirror 1.50 THULE-OMNISTOR awning in black, ESP incl. ASR and hill holder 0.50 325 - 400 cm 26.00 - 31.50 Fog lights 2.00 Living room Hub caps 2.40 Leather steering wheel and gear knob 0.50 Fitted carpet, living room and driver's cab, removable 5.60 Light alloy rims 16" (Original FIAT,...
  • Page 145 11-3 Accessories Object Weight[kg] Object Weight[kg] Packages TRUMA DuoControl incl. crash sensor and de-icer 2.10 TRUMA MonoControl CS (crash sensor) 1.00 VANTANA chassis package 24.20 USB charging socket, double 0.00 VANTANA light package 1.40 Waste water tank, heated 1.00 VANTANA starter package 13.90 Wireless alarm system with gas alarm for narcotic gases, propane and butane 1.00 WLAN control for LCD Control Panel 0.00 Heating/air-conditioning DOMETIC roof air-conditioning system 30.00 TRUMA heating Combi 6 E instead of Combi 4 1.10 Multimedia 2 additional loudspeakers in the living area 2.00 BLAUPUNKT navigation system incl. rear view camera 4.70 CD/radio 1.50 Extendable shelf for flat screen TV 3.00 Reverse drive video system with colour screen and flat screen 2.00...
  • Page 146 Accessories 11-4...

  • Page 147: Chapter 12: Maintenance And Care Maintenance

    Maintenance intervals For safety reasons, spare parts for equipment must conform with the manufacturer‘s instructions and must be installed There are stipulated maintenance intervals for the van and its by him or a duly authorised representative. equipment. The following applies for maintenance intervals: Hobby recommends that you contact a service partner before • Have the first maintenance carried out by a HOBBY dealer driving there and inquire whether they have the necessary 12 months after the vehicle was first registered. capacity (e.g. an adequate car lift) in order to avoid any • All further maintenance should be carried out once a year misunderstanding. by a HOBBY dealer. • The maintenance of the basic vehicle as well as all built-in equipment should be carried out at the intervals given in each operating manual.

  • Page 148: Brakes

    Maintenance and Care 12-2 12.2 Brakes 12.3 Airing The components in the brake system are part of the General For a comfortable climate inside the van, there must be suf- Type Approval (“Allgemeinen Betriebserlaubnis“, ABE). ficient ventilation. This also avoids corrosive damage due to If you change the components in the brake system, the type condensation. approval expires. Any changes are only possible if they have been released by the manufacturer. Condensation is caused by - insufficient volume inside the van It is in your own interest to have the brakes checked - breathing and perspiration of the passengers regularly by your Fiat workshop. - bringing in damp clothing - operating a gas cooker The following applies when maintaining the brake system: Ensure that there is a sufficient exchange of air to avoid • Check the level of brake fluid regularly.

  • Page 149: Care

    12-3 Maintenance and Care 12.4 Care - alcohols - aggressive or solvent-based cleaners The following applies for their care: - cleaners from the chemical group such as • Clean plastic parts (e.g. fenders, skirts) with water of up to ketone, ester and aromatic solvents 60° C and mild household cleansers. - aromatic hydrocarbons (e.g. all automotive fuels) • Clean greasy or oily surfaces with spirits. Direct contact with plastics such as PVC, soft PVC and similar products (e.g. stickers) must be avoided at all cost. Wash the vehicle only in places provided for this purpose. It is not possible to avoid transmitting plasticizers when solvent- based contents come into contact with the aforementioned Using cleaning materials sparingly. Aggressive cleansers, plastics and this causes the parts to become brittle. such as wheel rim cleaners, damage the environment.
  • Page 150 Maintenance and Care 12-4 The following applies when waxing the surfaces: Dry the headlights and sockets thoroughly, as water collects • The varnished surfaces should be treated occasionally there easily. with wax. Follow the application instructions given by the wax manufacturers. Washing with a high pressure cleaner The following applies when polishing the surfaces: • In exceptional cases, use polish to refinish weathered varnis- Do not spray stickers and external decors directly with the high pressure cleaner as they could peel away as a result. hed surfaces. We recommend solvent-free polishing paste. Before washing the van with a high pressure cleaner, study Use polish only in special cases and as seldom as possible, its operating manual carefully. During washing maintain a because polish removes the top layer of varnish. Frequent minimum distance of 700 mm between the van and the high polishing causes extreme wear.

  • Page 151: Cleaning The Interior

    12-5 Maintenance and Care Cleaning the interior The following applies for damages: • Repair damages immediately to avoid further damages due to corrosion. Ask your HOBBY dealer for assistance. To reduce problems arising from dampness, use water sparingly when cleaning inside. Skylights, windows and doors The following applies for cushions, upholstery and Window panes require particularly careful treatment. curtains: • Clean cushions with a soft brush or hoover. The following applies for their care: • Have very dirty upholstery and curtains dry-cleaned. Do • Rub the rubber seals around doors and windows lightly...
  • Page 152 Maintenance and Care 12-6 Cleaning instructions for materials that containTeflon Method B: • Use only mild, water-free solvents for dry cleaning. • Dampen the cloth and proceed as described in method A. • Always treat spots immediately. • Sponge spots, but do not rub them. • Work from the edge towards the middle of the spot. This method is particularly suitable for removing: • Never use household cleaners to remove spots. - wax, candles • Hoover cushions regularly to remove any dirt that may - pencil have collected. We recommend the following methods for cleaning: Chocolate or coffee should only be washed out with luke- Method A: warm water. The following applies for carpeted floors: • Use only commercial cleaning agents that have a water • Clean with a hoover or brush.
  • Page 153 Maintenance and Care 12-7 • Use cleansing agents for PVC floors and clean water when • The rubber seals of the toilet should be cleaned regularly washing the floor. Do not place fitted carpets on a wet with plain water and a lubricant for seals (not Vaseline or PVC floor, as the fitted carpet and the PVC flooring could any other vegetable fats) should be applied. Applying this become glued together. regularly to the washer of the valve and other seals in the • Never use chemical cleansing agents or steel wool, be- toilet will ensure that they stay flexible and function longer. cause this will damage the PVC flooring. Do not pour any corrosive substances down the drains. Do not pour boiling water down the drains. Corrosive The following applies for furniture surfaces: substances and boiling water damage drain pipes and • Clean the surface of wooden furniture with a damp cloth or syphons. sponge. • Rub dry with a dust-free cloth. The following applies for the sink and the cooker: • Use mild furniture polish.

  • Page 154: Winter Lay Up For The Van

    Maintenance and Care 12-8 12.5 Winter Lay Up for the Van • The exterior should be treated with wax or a special polish for varnish. For many people, the camping season ends when the tempe- • Use a protective agent to protect the metal parts of the rature starts to fall. Your van must be properly prepared for its chassis against rust. winter lay up. • Check the undercarriage for damage and, if necessary, drive to your dealer to have it repaired. The following general rules apply: • Ensure that no water can get into the venting on the floor, • Only leave your van in a closed space if it is dry and well- heating system and refrigerator venting (mount winter aired. Otherwise, it is better to leave your van in the open. covers • To protect the tyres, jack up the van or move it slightly to a new position every two months. • Close all gas bottles and emergency shutoff valves. The following applies for tanks and containers: • Disconnect (or, ideally, remove) the battery and store it • Clean, disinfect, descale and completely empty all water...

  • Page 155: Winter Operation

    Maintenance and Care 12-9 12.6 Winter Operation The following applies for the interior fittings: • Clean the interior of your van. Hoover carpets, cushions and mattresses. If possible, store them outside the van. Other- Preparations wise, place them in such a way inside the vehicle that they Your van has been designed to allow you to use it to a certain do not come into contact with condensation. extent in winter. If you really wish to camp in winter, we • Use soapy water to clean linoleum and smooth surfaces. recommend that you optimize your van to meet your personal • Empty and clean the refrigerator. Leave the refrigerator requirements. Your dealer will be pleased to advise you. door in the ventilation position (see 10.6). • After cleaning them, leave stowage spaces, cupboards, The following applies for your preparations: drawers and furniture flaps open to facilitate air circulation. • Check the vehicle for damage to the paintwork or from • Leave vents for forced ventilation open. If the van is kept in rust and, if necessary, repair it.
  • Page 156 Maintenance and Care 12-10 • Do not shut vents for forced ventilation. • Do not let the interior cool down completely when you are • Set the heating to maximum power when heating up the away or at night; set the heating to low and leave it on. van. Open stowage spaces, cupboards, drawers, furniture flaps, curtains, shades and plissés. This enables you to Continue to heat the vehicle while you are sleeping! achieve optimum ventilation and de-aerating. • Only heat the van when the recirculation air system is swit- • The van uses considerably more gas in winter than in sum- ched on. mer. Two 11 kg bottles of gas will be used up in just under • Every morning, air all of the cushions, mattresses and one week. stowage spaces and dry any damp spots. • Therefore, should you stay longer in one place, it is wor- • Air thoroughly with fully opened doors and windows sever- thwhile to set up an outer tent. It will help to acclimatise al times a day.

  • Page 157: At The End Of The Winter Season

    12-11 Maintenance and Care At the end of the winter season Saving energy in winter The following applies for the care of the vehicle: It is very easy to save energy inside your van. This applies • Thoroughly wash the underbody and the motor. This removes especially to heating in winter. corrosive thawing agents (salts, alkali). • Clean the exterior and use normal car wax to preserve metal The following applies for saving energy: parts.
  • Page 158 Maintenance and Care 12-12...

  • Page 159: Chapter 13: Sanitation And Environmental Protection

    13-1 Sanitation and Environmental Protection Chapter 13: Sanitation and Environmental Protection 13.1 The environment and traveling Environmentally fair use It is only natural that owners of motor home, caravan and van have a special responsibility for the environment. Always use The following applies for environmentally fair use: your vehicle in an environmentally friendly way.
  • Page 160 Sanitation and Environmental Protection 13-2 The following applies for waste water: The following applies for wastes: • Collect waste water on board only in built-in waste water • Only use approved sanitary cleansing products in the waste tanks or, if necessary, in suitable containers! tank. • Never empty waste water in open spaces or down man- You may be able to avoid the use of sanitary liquids by holes! Generally, the public waste water system does not installing an activated carbon filter system (sold as an run through clarification plants.
  • Page 161 13-3 Sanitation and Environmental Protection Sanitation • Never allow the waste tank to become too full. Empty the tank immediately as soon as the level indicator lights up. • Never empty wastes down manholes! Generally, the pu- blic waste water system does not run through clarification plants. Empty the waste tank in special places for sanitary disposal, but never in open spaces! The following applies for waste: • Separate your waste and put appropriate materials in the recycling bins. • Empty waste bins as often as possible in the appropriate bins or containers. This avoids unpleasant and problematic waste from building up on board.

  • Page 162: Returning The Vehicle

    Sanitation and Environmental Protection 13-4 13.2 Returning the vehicle Protecting the environment is not only in the interest of nature, but also in the interest of all motor home, van and caravan users! If you should ever have to give up your van and have it recycled, the manufacturer of the basic vehicle is responsible for taking it back (status at the time of printing). This means that your HOBBY van must be taken back free of charge by any Fiat dealer and expertly recycled.

  • Page 163: Chapter 14: Technical Data

    14-1 Technical Data Chapter 14: Technical Data 14.1 Chassis Data Hobby Model Type Base Motorisation exhaust Chassis Towbar Belt system Seats Model Modell vehicle Sawiko Typ Aguti emissions FIAT Ducato X290 Vantana Ducato Light 115 Multijet (85 kW) Euro 5b+...
  • Page 164 Technical Data 14-2 t.p.o.w. Permiss. Permiss. Unbraked Braked Max. Maximum Total Height Width Front Rear Wheel Front Rear [kg] front axle rear axle trailer trailer permissible towing length tread tread base projec- projec- load load load load drawbar weight width width tion tion...

  • Page 165: Load Increased For Van

    14-3 Technical Data 14.2 Load increased for vans Hobby Model Type Base Seats t.p.o.w. Permissible Permiss. Unbraked Braked Max. Maximum front axle rear axle towing [kg] trailer trailer permissible Model vehicle load load weight load load drawbar load FIAT Ducato X290...
  • Page 166 Technical Data 14-4 Total Height Width Front Rear Wheel Front Rear length tread tread base projection projection width width 5413 2642 2050 1810 1790 3450 1015 5998 2642 2050 1810 1790 4035 1015 5998 2642 2050 1810 1790 4035 1015 5998 2669 2050...

  • Page 167: Vehicle And Equipment Weights

    14-5 Technical Data 14.3 Vehicle and equipment weights Model Series Weight of Driver Diesel Unladen Basic Mass when t.p.o.w. Overload basic [kg] weight equipment vehicle is [kg] weight vehicle [kg] ready to start FIAT Ducato X290 Vantana 2343 2487 2598 3300 Vantana 2541...
  • Page 168 Technical Data 14-6 Sitzplätze Mass of Loading Sleeping Length of Minimum Control value passengers capacity spaces vehicle loading (PSI) capacity FIAT Ducato X290...
  • Page 169 14-7 Technical Data 14.4 Tyres and rims for vans Light chassis Series Optional extra Hobby Series t.p.o.w. Perm. axle Perm. axle Tyre size Metal wheel rim Tyre size Metal wheel Wheel Model [kg] load front load rear rim, optionally attachment...
  • Page 170 Technical Data 14-8 Tyres and rims for loaded vans Maxi chassis (increased load) t.p.o.w. Perm. axle load Perm. axle Tyre size Metal wheel rim, Wheel [kg] front load rear optionally alloy attachment wheel rim 4000 2100 2400 225/75 R 16 C 6 J x 16, ET 68 5 / 78 / 130 4000...

  • Page 171: Inflation Pressures

    14-9 Technical Data 14.5 Inflation pressures Tyres Tyre pressure (bar) Basis Michelin XC Camping 215/70 R 15 C front: 5,0 rear: 5,5 FIAT 225/75 R 16 C front: 5,5 rear: 5,5 FIAT other tyre manufacturers 215/70 R 15 C front: 4,1 rear: 4,5 FIAT 225/75 R 16 C...
  • Page 172 Technical Data 14-10...

  • Page 173: Index

    Ix-1 Index Index in curves 02-9 Freezer compartment 10-17 in reverse 02-9 Fresh water tank 08-2 Mains connection 07-19 sparing the tyres 04-1 to empty 08-5 Maintenance intervals 12-1 Driving economically 02-9 FrostControl 10-13 Mass when ready to drive 03-3 Driving in curves 02-9 Furniture doors 06-2 Modular battery 07-23...
  • Page 174 Index Ix-2 Roof air conditioning 10-21 toilet 12-7 Roof bonnets 06-17 windows and doors 12-5 Safety belts Valve for waste water tank 08-4 in the superstructure 06-22 Valves 09-2 Seats in the superstructure 06-19 Vehicle Identification Number 03-1 Seats Ventilation grills 05-1 overview 06-23 Securing the vehicle 02-10 Shunting 02-9...
  • Page 175 Hobby-Wohnwagenwerk Ing. Harald Striewski GmbH Harald-Striewski-Straße 15 D-24787 Fockbek/Rendsburg www.hobby-caravan.de...

Table of Contents