Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for D&K Monarchy Minikote EZ G3
- Page 1 OWNERS MANUAL Minikote EZ 652792 Laminator.com www.laminator.com...
-
Page 2: Table Of Contents
CONTENTS Section Index Speci cations ...........................1 Important Safeguards .......................2 General Diagrams ........................3 - 4 I. Unpacking ..........................5 II. Information About Laminating Film ..................5 III. Operating A. Control Panel .......................5 B. Loading Film: 1” Mandrel .....................6 C. Threading Film ......................7 D. Laminating ........................8 E. -
Page 3: Specifications
SPECIFICATIONS Height .................. 15” Width ................... 34” Depth (with feed tray ) ............20” Net Weight ................66 lbs. Shipping Weight ..............72 lbs. Capacity................27” Electrical ................120V AC, 60Hz, 1400w Laminator.com www.laminator.com... -
Page 4: Important Safeguards
IMPORTANT SAFEGUARDS • Read all the safety and operating instructions before connecting or using this unit. • Retain this notice and the owners manual for future reference. • Adhere to all warnings and operating instructions. • Do not use this unit near water (e.g. near a bathtub, etc.) •... -
Page 5: General Diagrams
GENERAL DIAGRAMS The Minikote EZ, offers a reverse feature. They are designed to laminate a variety of materials using up to 27” laminating lm. The Minikote EZ is capable of lamination from 1 to 9 feet per minute and can be reversed by the push of a button. - Page 6 GENERAL DIAGRAMS Laminator.com www.laminator.com...
-
Page 7: Unpacking
I. Unpacking I. Unpacking Remove the laminator from its box by grasping the housings and pulling up. Do not use rollers or shafts as handles - this could cause damage. Choose a location for the laminator that is clean, well-lit and draft free. -
Page 8: Loading Film: 1" Mandrel
B. Loading Film: 1” Mandrel (K) B. Loading Film: 1” Mandrel (K) Unpack the upper and lower supply man- drels. The upper and lower mandrels are different. The word “TOP” is stamped on the shaft of the upper mandrel and the word “LOW”... -
Page 9: Threading Film
C. Threading the Film C. Threading the Film Remove the feed tray and the heatguard. Thread the lm as shown in the gure on the right. Pull the lm around the idler rollers as shown. Do not mistake the reinforcing bar for the Do not mistake the reinforcing bar for the idler roller idler roller. -
Page 10: Laminating
D. Laminating D. Laminating After the machine is loaded with lm (see B. Loading Film: 1” Mandrel) and threaded (see C. Threading the Film), it is ready to laminate. Ensure that the laminator has reached the preset temperature. This will be indicated by the ready light being illu- minated. -
Page 11: Maintaining The Minikote Ez
Note Note: As the diameter of the lm roll decreases, tension should be reduced. To increase tension, turn the adjusting knob clockwise. To decrease tension, turn the knob counterclock- wise. If the tension is not equal top and bottom, the laminated product will curl. If the material curls up up as it comes out of the machine, the top roll is probably tighter than the bottom. -
Page 12: Speci C Troubleshooting Guide
B. Speci c Troubleshooting Guide B. Speci c Troubleshooting Guide Wrinkles on Film (side to side) Wrinkles on Film (lengthwise) Plastic not bonding Bubbles or Blisters Impressions on product Squeaking sounds Film narrowing on shoes Film wrinkling on shoes Continuous blemish Cloudy lm “Orange Peel”... -
Page 13: Replacing The Hand Held Cutter Blades
Shut the machine off! Shut the machine off! Minikote EZs have set screws at both ends of each laminating and pull roller. With the use of a 3/32 hex key, loosen all four set screws on the pull rollers. Cut the plastic between the lami- nating and pull rollers, grab the loose end and pull. -
Page 14: Exploded Diagram
EXPLODED VIEW Laminator.com www.laminator.com... -
Page 15: Warranty
LIMITED WARRANTY Dealer, warrants to the original consumer purchaser that each new Minikote EZ Laminator which proves defective in materials or workmanship within the applicable warranty period will be repaired or, at our option, replaced without charge upon its return as outlined below. The applicable warranty shall be one year from date of purchase.
Need help?
Do you have a question about the Minikote EZ G3 and is the answer not in the manual?
Questions and answers