Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco PRO 3 BAGGER
Summary of Contents for Peco PRO 3 BAGGER
- Page 1 P P P PRO 3 BAGGER GRASS COLLECTION PECO PECO PECO PECO PECO SYSTEM ENGINE DRIVEN TORO Z-MASTER 48” - 52” - 60” G3, 3000, 5000 DECKS & 6000 SERIES 22131537 (900 SERIES) 22131540 (6.5HP) OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0385 $10.00...
-
Page 2: Table Of Contents
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
INTRODUCTION AND DESCRIPTION 1-1 Introduction Rotating The Donaldson Air Cleaner We are pleased to have you as a PECO customer. Your Note: If equipped with a Donaldson air cleaner, unit collection system has been designed to give you a low... -
Page 6: Main Frame Assembly Information
2-2 Main Frame Assembly 2-3 Outer Engine Mount Tube Installation Cont... Assembly Installation Figure 2-2b shows the mounting position for the lower Remove the lower 4 existing bolts from the rear heat frame legs, P#(B0528 - Right) and P#(B0529 - Left). guard as shown in Figure 2-3a. -
Page 7: Engine Mount Arm Installation
2-4 Lower Mount Clamp Bracket 2-6 Engine/Blower/Blade Assembly Installation Cont... Installation Place the engine/blower/blade assembly onto the engine Inside View Figure 2-4a mount arm assembly (Figure 2-5 and 2-6). Secure the engine/blower/blade assembly to the engine mount arm assembly by using (4) 5/16"-18 x 1-1/2" HHCS P#(K1157) and (4) 5/16"-18 nyloc nuts P#(K1180) as shown in Figure 2-6. -
Page 8: Upper Frame Assembly Installation
2-8 Exhaust Deflector Plate Installation Figure 2-9b Upper Frame Assembly An exhaust deflector plate is required to prevent exhaust diverter from touching the collection bags. Fasten the exhaust deflector plate P#(C0061) to the bumper on the left rear side of the mower using the existing hex bolt (step 2-2a, page 5) used to mount lower main frame leg. -
Page 9: Top Assembly To Upper Frame Assembly
2-12 Inlet Installation 2-10 Top Assembly To Upper Frame Assembly Installation Slide the inlet P#(V0025) into the hole on the bagger top Position the top assembly P#(A1157) above the upper until the inlet locks into place. The inlet should pivot 360 frame assembly as shown in Figure 2-10. -
Page 10: Blower Cone Installation
2-14 Blower Cone Installation 2-15 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially WARNING thread the bolts into each of the two tabs located on the blower housing. Place blower cone so the two tabs line up with the bolts then tighten completely. -
Page 11: Throttle Cable Installation
2-16 Throttle Cable Installation Figure 2-16c To install the throttle cable kit to the ROPS (roll over protection system), place the 3/8” U-Bolt P#(K0136) onto the ROPS with the threads facing the front of the mower. Next slide on the throttle mount plate assembly P#(A0666) with the rivets also facing toward the front of the mower. -
Page 12: Length Of Hose Adjustment
2-17 Length Of Hose Adjustment The hoses in steps 2-18 and 2-19 must be cut to fit your mower. Follow steps 2-18 and 2-19, however, do not cut the hoses until you have tried to fit them on your Figure 2-19 mower. -
Page 13: Installation And Removal Of Collection Bags
2-21 Installation/Removal Of Figure 2-21c Collection Bags Plastic Top IMPORTANT! To prevent bag wear, install (2) red plastic end caps P#(J0274), as shown in Figure 2-21a, on each bag ring before installing bags. Figure 2-21a Bag Ring Red Plastic End Caps Fasten Draw -Latch Here &... -
Page 14: Exploded Views And Parts List
Exploded Parts View A1157 Top Assembly Item # Doc # Title V0022 PRO 3 BAGGER TOP B0676 Hinge Stop Pl. K0114 BLACK PLASTIC RIVET C0069 DUST GUARD BRACE K1030 1/4"-20 x 1-1/4" CARRIAGE BOLT J4009 SHORT RUBBER STRAP W/ S HOOK K0037 1/4"... -
Page 17: Operating Instructions
* Remember that horsepower requirements will vary with PECO parts. the mowing conditions such as type and height of turf grass, moisture content, amount of leaves, whether the After Each Use: terrain is flat or sloped, etc. -
Page 18: Parts And Service
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PeCo collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system. -
Page 19: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R1051 Warning: Hearing Protection Label... - Page 21 NOTES...
- Page 22 P P P PECO PECO PECO PECO PECO 100 AIRPORT ROAD ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...
Need help?
Do you have a question about the PRO 3 BAGGER and is the answer not in the manual?
Questions and answers