Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Martin Mania DC2
Summary of Contents for Martin Mania DC2
- Page 1 Mania DC2 user manual...
- Page 2 © 2003 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. Printed in China. P/N 35000138, Rev. B.
-
Page 3: Table Of Contents
Focusing the Mania DC2 ........ -
Page 4: Introduction
NTRODUCTION Thank you for selecting a Martin Mania DC2. The Mania DC2 is a luminaire that projects a 53° beam rising-flames effect at user-selectable speed. S A F E T Y I N F O R M A T I O N Warning! This product is not for household use. - Page 5 The lamp shall be changed if it becomes damaged or thermally deformed. If the external power cord of this luminaire is damaged, it shall be replaced by a special cord exclusively available from your Martin dealer. Avoi di ng electric shocks...
-
Page 6: Unpacking
U N P A C K I N G The packing material is carefully designed to protect the fixture during shipment - always use it to transport the fixture. The Mania DC2 comes with the following: • 3-wire IEC power cable • User manual... -
Page 7: Installation
Martin dealer. Configuring for local mains power The Mania DC2 has a switch-selectable power supply that can operate in the following voltage ranges at 50-60 Hz: • 115 - 120 volts (setting 115) •... - Page 8 Applying power 1 Connect the mains power cable to the fixture at the 3-prong IEC male input socket on top of the fixture. Mains socket Power on switch 2 Turn the power on using the power-on switch. Mania DC2 user manual...
-
Page 9: Overhead Mounting
O V E R H E A D M O U N T I N G The Mania DC2 can be hung overhead with a clamp (not included). Warning! Block access below the work area before proceeding. Always use a secure means of secondary attachment. -
Page 10: Changing Effect Orientation
1 Ensure that the fixture is disconnect from power and has been allowed it to cool for 5 minutes. 2 Remove the thumb screw holding the cover in place. Thumb screw Mania DC2 user manual... - Page 11 3 Slide the fixture cover open as far as possible (there is a physical stop point that prevents access to the power supply section). 4 The gobo can be found close to the lamp. Remove the gobo from its holder. We recommend that you carefully press the gobo out from the lamp side using a flat-head screwdriver...
-
Page 12: Operation
• Adjust effect (rotation) speed. This dial is used to adjust the speed at which the flames rise. Power on switch Effect speed (rotation speed) Effect direction (rotation direction) Mania DC2 user manual... -
Page 13: Focusing The Mania Dc2
F O C U S I N G T H E M A N I A D C 2 The focus is adjusted using the mechanism next to the lens. Pull the mechanism out, or push it in, until a sharp image is acquired. Operation... -
Page 14: Basic Service
C L E A N I N G Regular cleaning of the elements in the optical path, as well as the air vents, is vital to maintaining the operational quality of the Mania DC2. Important! Excessive dust, smoke fluid, and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty. -
Page 15: Lamp Maintenance
2 Remove the thumb screw holding the cover in place. Thumb screw 3 Slide the fixture cover open as far as possible (there is a physical stop point that prevents access to the power supply section). 4 Vacuum or gently blow away dust and loose particles with compressed air. - Page 16 Caution Hot lamp. Only the Philips 12V EFP/8H 100W (type No 6834) lamp is supported (Martin P/N 97000004). These lamps normally last for 800 hours of operation. Warning Installing any other lamp may damage the fixture! I ns ta ll in g a lamp i n the M an ia D C2 1 Disconnect the fixture from power and allow it to cool for 5 minutes.
-
Page 17: Mains Fuse
9 Close the fixture cover and tighten the thumb screw. M A I N S F U S E The Mania DC2 uses a time-delay fuse for protection against current overload. An indication that the fuse may have blown is that when power is applied and the lamp is switched on, no light is produced. -
Page 18: Troubleshooting
Burned out lamp Install new lamp Fixture to hot Allow to cool Improve air flow around fixture No action Electrical malfunction Refer to a Martin service technician Fuse blows repeatedly Electrical malfunction Refer to a Martin service technician Mania DC2 user manual... -
Page 19: Specifications
PECIFICATIONS P H Y S I C A L Size without mounting bracket (LxWxH) . . 312 x 250 x 142mm (12.3 x 9.8 x 14.2in) Weight..........6.3 kg (14lb) C O N S T R U C T I O N Housing. - Page 20 Mania DC2 US version ........
- Page 24 • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark Tel: +45 8740 0000 • Fax +45 8740 0010...
Need help?
Do you have a question about the Mania DC2 and is the answer not in the manual?
Questions and answers