Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Erbauer ERI616HTL
Summary of Contents for Erbauer ERI616HTL
- Page 1 ERI616HTL 18V MULTI TOOL ERI616HTL...
- Page 2 Original Instructions (Version 3.0)
- Page 3 Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This product should give you reliable service but for your peace of mind this power tool does carry a 2 year guarantee, the terms of which are detailed below.
-
Page 4: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS Warning Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 5 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 18V MULTI TOOL ERI616HTL...
- Page 6 b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
- Page 7 3. Before charging, read the instructions. 4. After charging, disconnect the battery charger from the supply mains. Then remove the chassis connection and then the battery connection. 18V MULTI TOOL ERI616HTL...
-
Page 8: Safety Warnings For Battery Pack
5. Do not charge a leaking battery. 6. Do not use chargers for works other than those for which they are designed. 7. Before charging, ensure your charger is matching the local AC supply. 8. For indoor use, or do not expose to rain. 7. - Page 9 Retain the original product literature for future reference. r) Remove the battery from the equipment when not in use. s) Dispose of properly. Warning: If a small amount of electrolyte should leak from the battery pack under extremes of temperature or after 18V MULTI TOOL ERI616HTL...
- Page 10 heavy use, then wash off immediately from your skin and hands using clean water. For eye contact, rinse thoroughly with clean water and seek medical treatment immediately. ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST The updated Control of Substances Hazardous to Health Regulations 1st October 2012 now also targets to reduce the risks associated with silica, wood and gypsum dusts.
- Page 11 Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals: • Work in a well-ventilated area. • Work with approved safety equipment, such as those dust masks that are specially designed to filter microscopic particles. 18V MULTI TOOL ERI616HTL...
- Page 12 VIBRATION The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to provide indicative vibration test results to enable users to make informed decisions as to the period of time a power tool can be used safely on a daily basis and the choice of tool.
- Page 13 Fast intervention can prevent serious injury and damage to property. 2. Switch off and disconnect from the power supply if there is any malfunction. Have the product checked by a qualified specialist and repaired, if necessary, before you put it into operation again. 18V MULTI TOOL ERI616HTL...
- Page 14 SYMBOLS To reduce the risk of injury, user must read instruction manual Warning Double insulation Wear ear protection Wear eye protection Wear dust mask Indoor use only Wear protective gloves Fuse T 2A time lag fuse with rated current of 2A Positive terminal Negative terminal Do not expose to rain or water...
- Page 15 18V MULTI TOOL ERI616HTL...
- Page 16 ON/OFF SWITCH BATTERY PACK RELEASE BUTTON BATTERY PACK VARIABLE SPEED CONTROL VENTING SLOT FLANGE HEX KEY PRECISION WOOD CUT BLADE HSS SEMICIRCLE SAW BLADE SANDING PAD (PERFORATED) SMALL FLANGE...
-
Page 17: Technical Data
Charger High carbon steel Precise Saw Blade 34x92mm HSS Segment Saw Blade Sanding Plate 80# Sanding sheet 5pcs 120# Sanding sheet 5pcs 180# Sanding sheet 5pcs Hex key (5mm) Big flange (pre-fitted on machine) Small flange 18V MULTI TOOL ERI616HTL... -
Page 18: Intended Use
OPERATION INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. INTENDED USE The power tool is intended for sawing and separating wooden materials, plastic, plaster, non-ferrous metals and fasteners (e.g. nails and clamps) as well as for working on soft wall tiles and Fig. -
Page 19: Charging Procedure
Battery Pack, have the charger tested at an authorized service center. Light ON/OFF flash Status Red on Charging Defective Red flash Battery Fig. 2-2 Fully Charged Green on Hot/Cold Delay Green flash Fig. 2-3 18V MULTI TOOL ERI616HTL... -
Page 20: Operation
Fig. 1-3 OPERATION Warning: Do not touch the gear box after long working time, because it could be hot. 1. MOUNTING THE TOOL (See Fig. 2-1-2-3) Caution: For all work or when changing application tools, always wear protective gloves. Avoid danger of injury from the sharp Fig. -
Page 21: Operating The On/Off Switch
The variable speed control (4) can be used to set the optimum oscillating frequency according to the accessories used and the respective application. High oscillation frequency: Sanding, sawing, rasping and polishing stone and metal. Low oscillation frequency: Polishing varnishes. Fig. 5 18V MULTI TOOL ERI616HTL... - Page 22 APPLICATION WARNING: The sawing teeth are very sharp. Do not touch during mounting and application. The workpiece must be clamped tightly before it is cut. Description Application Wood, plastic, fiberglass, Universal Metal/Wood End nails, non-ferrous metals, thin Cut Blade sheet metal, hardened fillers Standard Wood End Cut Wood, plastic, drywall Blade...
-
Page 23: Working Hints For Your Tool
Start your tool before working and turn it off only after you stop working. Do not start sanding without having the sandpaper fitted. Do not allow the sandpaper to wear away , it will 18V MULTI TOOL ERI616HTL... -
Page 24: Maintenance
damage the sanding pad. The guarantee does not cover sanding pad wear and tear. Use coarse grit paper to sand rough surfaces, medium grit for smooth surfaces and fine grit for finishing surfaces. If necessary, first make a test run on scrap material. -
Page 25: Plug Replacement
5 Amp fuse approved to BS1362 Connect Blue to N Brown L(live) (neutral) Outer sleeve Cable grip firmly clamped 18V MULTI TOOL ERI616HTL... -
Page 26: Declaration Of Conformity
EN 55014-2 EN 60745-1 EN 60745-2-4 EN 61000-3-2 EN 61000-3-3 EN 60335-1 EN 60335-2-29 Authorised Signatory and technical file holder Date: 12/01/15 Signature: Name / title: Peter Harries / Quality Manager Erbauer (UK) Ltd. Trade House, Mead Avenue, BA22 8RT...
Need help?
Do you have a question about the ERI616HTL and is the answer not in the manual?
Questions and answers
fit a charged battery, lights are on but multitool does not run when pushing switch n.
If the lights on the Erbauer ERI616HTL multitool are on but it does not run when the switch is pushed, the issue could be due to the following reasons:
1. Hot/Cold Delay – If the green light is flashing, the battery may be too hot or too cold, preventing operation. Allow the battery to reach normal temperature.
2. Defective Battery – If the red light is flashing, the battery may be defective and need replacement.
3. Loose or Incorrectly Mounted Accessory – Ensure the accessory is securely tightened using the flange and Allen key.
4. Overheating – If the tool has been running for a long time, the gearbox may be hot. Allow it to cool before use.
5. Electrical Issue – Check if the battery is fully charged and properly connected to the tool.
If none of these resolve the issue, contact the retailer for further assistance.
This answer is automatically generated