The Andersons LCO-1000 Assembly, Use And Care
  1. Manuals
  2. Brands
  3. The Andersons Manuals
  4. Spreader
  5. LCO-1000
  6. Assembly, use and care

The Andersons LCO-1000 Assembly, Use And Care

Professional rotary spreader
Hide thumbs Also See for LCO-1000:

Advertisement

Table of Contents

Assembly, Use and Care
Thank You!
You have purchased the highest quality professional broadcast spreader available on the market today. The
LCO-1000 is the accumulation of proven performance and will provide you with years of trouble-free service. In
the event you should have any questions or comments, please call our professional support staff.
Our toll-free number is

Before You Begin ...

To assemble your new
spreader, we highly
recommend that you read
all the instructions thoroughly,
familiarize yourself
with the assembly and
components, and verify that all
parts are included in the
package.
You Will Need ...
The following tools:
7/16" open-end wrench
—
(or adjustable wrench
Pliers
—
Grease gun
—
1-800-225-2639
)
Model LCO-1000
(U.S. Only)
Professional Rotary Spreader

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LCO-1000 and is the answer not in the manual?

Questions and answers

Related Manuals for The Andersons LCO-1000

Summary of Contents for The Andersons LCO-1000

  • Page 1: Before You Begin

    You have purchased the highest quality professional broadcast spreader available on the market today. The LCO-1000 is the accumulation of proven performance and will provide you with years of trouble-free service. In the event you should have any questions or comments, please call our professional support staff.
  • Page 2 Assembly Turn the spreader upside-down. Place the Install control tube to the handle lever with wheels on the axle with the longer portion of the (1) 1/4 dia. clevis pin and a 3/32” dia. cotter pin. hubs facing inward. Secure the drive wheel “A” (right Remove the paper tube on the end of the lower control side) to the axle using the 3/16”...

  • Page 3: Operation

    Operation Pointer HOW TO USE Check product bag for rate setting (letter), and swath width. The rate setting is achieved by loosening the rate control knob and sliding the rate control plate until the pointer aligns with the desired letter. Pull the main shutoff lever to the closed position before filling Rate Control Rate Control...

  • Page 4: Maintenance

    Maintenance Empty the spreader after each use. Return the Gear mesh should be checked on a regular unused material to its original container and seal to basis during high use periods. Clearance between prevent moisture-caused clumping. the axle gear and pinion gear should be minimal but not tight.

  • Page 5: Calibration Instructions

    Calibration Instructions Calibration depth Calibration Key Pointer Setting “E” Rate Control Plate Your professional spreader has been factory calibrated. For best results, occasionally check calibration and adjust if necessary. Pull the main shutoff lever to the closed posi- Slide the rate control plate to the right until it tion.
  • Page 6 Parts Diagram–LCO-1000 #16579 Optional Deflector Kit (Used for side spread pattern shutoff)

  • Page 7: Ordering Parts

    Ordering Parts See diagram for assistance in identifying specific parts. For parts orders, call 1-800-294-0671. (Note: Sales of parts for the Andersons spreaders are handled by EarthWay IMPORTANT: When ordering replacement parts, always provide the following information: 1) Part number (DO NOT use key numbers when ordering parts. ALWAYS use part numbers.)

  • Page 8: Warranty

    This warranty does not extend to any Product or parts thereof that have been allowed to corrode, subjected to misuse, neglect, accident, or modification by anyone other than The Andersons or that have been affixed to any nonstandard accessory attachment or that have been used, stored, installed, maintained operated in violation of The Andersons instructions or standard industry practice.

Table of Contents