Advertisement
Professional Shop Manual
Remington 22" Trimmer Mower
NOTE: These materials are for use by trained technicians who are experienced in the service and repair of outdoor power
equipment of the kind described in this publication, and are not intended for use by untrained or inexperienced individuals.
These materials are intended to provide supplemental information to assist the trained technician. Untrained or inexperi-
enced individuals should seek the assistance of an experienced and trained professional. Read, understand, and follow all
instructions and use common sense when working on power equipment. This includes the contents of the product's Oper-
ators Manual, supplied with the equipment. No liability can be accepted for any inaccuracies or omission in this publication,
although care has been taken to make it as complete and accurate as possible at the time of publication. However, due to
the variety of outdoor power equipment and continuing product changes that occur over time, updates will be made to these
instructions from time to time. Therefore, it may be necessary to obtain the latest materials before servicing or repairing a
product. The company reserves the right to make changes at any time to this publication without prior notice and without
incurring an obligation to make such changes to previously published versions. Instructions, photographs and illustrations
used in this publication are for reference use only and may not depict actual model and component parts.
© Copyright 2013 MTD Products Inc. All Rights Reserved
MTD Products Inc. - Product Training and Education Department
Advertisement
Table of Contents
Related Manuals for MTD remington
Summary of Contents for MTD remington
- Page 1 Instructions, photographs and illustrations used in this publication are for reference use only and may not depict actual model and component parts. © Copyright 2013 MTD Products Inc. All Rights Reserved MTD Products Inc. - Product Training and Education Department...
-
Page 3: Table Of Contents
Table of Contents About the text format..................... 1 Fasteners ......................3 Assembly instructions ................... 3 The 22” Trimmer Mower ..................3 Understanding model and serial numbers ............. 4 Trimmer Line ......................5 Skid Assembly ...................... 6 Spindle ........................7 Belt Replacement ....................10 Wheels and Axle .................... -
Page 5: About The Text Format
Common sense in operation and safety is assumed. • In no event shall MTD be liable for poor text interpretation, or poor execution of the procedures described in the text. If the person using this manual is uncomfortable with any procedures they encounter, they should seek the help... - Page 6 • Be prepared in case of emergency: ! CAUTION ! CAUTION Keep a fire extinguisher nearby Keep a first aid kit nearby Keep emergency contact numbers handy • Replace any missing or damaged safety labels on shop equipment. • Replace any missing or damaged safety labels on equipment being serviced. •...
-
Page 7: Fasteners
22” Trimmer Mower Fasteners • The fasteners used on the equipment described in this manual, and the engine that powers it are a combi- nation of metric and fractional inch. For this reason, wrench sizes are frequently identified in the text, and measurements are given in U.S. -
Page 8: Understanding Model And Serial Numbers
Please contact the designated support office in your area or our corporate offices directly should further service information be needed. MTD Products LLC P.O. Box 368022 Cleveland, OH 44136 Telephone: (800) 800-7310 www.mtdproducts.com... -
Page 9: Trimmer Line
22” Trimmer Mower Trimmer Line The trimmer line is a fixed length and can easily be replaced following the diagram on the front of the trimmer base assembly. See Figure 3. Disconnect and ground the spark plug wire. Remove the worn string from the spindle. Fold the replacement trimmer line in half and insert both ends through the loop near the edge of the spin- dle. -
Page 10: Skid Assembly
Skid Assembly NOTE: The skid assembly comes in contact with the ground during normal operation and will require replacement as normal mainte- nance. The skid assembly is available as service part number: 982-0143. See Figure 5. To remove/replace the skid assembly: Turn of the engine. -
Page 11: Spindle
22” Trimmer Mower Spindle NOTE: The spindle can not be serviced, and must be replaced as a unit if it gets damaged. See Figure 6. NOTE: The cutting height is adjusted by sliding the disc that the trimmer line is attached to up or down the spindle spindle shaft. - Page 12 Loosen the idler pulley nut and bolt with a pair of 1/ 2” wrenches, until the belt keeper opens. See Figure 9. belt keeper lock nut Figure 9 Slip the belt off of the idler pulley. See Figure 10. Idler Pulley Figure 10...
- Page 13 22” Trimmer Mower Disconnect the extension spring from the belt guide bracket. See Figure 11. NOTE: The extension spring applies tension to the idler pulley maintaining belt tension extension spring Figure 11 Remove the hex nut and hex bolt that hold the idler spacer pulley assembly to the trimmer base, using a pair of shoulder spacer...
-
Page 14: Belt Replacement
Belt Replacement IMPORTANT: Allow the engine to cool if it has been running. Disconnect and ground the spark plug wire. Drain the fuel tank. Position the trimmer so the rear edge of the trimmer base is resting securely on a work bench, and pivot the handle down. - Page 15 22” Trimmer Mower 13. Secure the pulley flywheel so that it will not spin during removal of the crankshaft bolt. See Figure 17. 14. Remove the crankshaft bolt using a 9/16” wrench. Wrench preventing the flywheel from turning flywheel Figure 17 15.
-
Page 16: Wheels And Axle
Wheels and Axle To remove the wheels and axle: axle bolt Remove the screw and washer that secures the washer wheel, using a 7/16” wrench. See Figure 19. NOTE: If the axle is being removed, the left wheel must be removed. NOTE: Both wheels are supported with an inner and outer sealed ball bearing Figure 19... -
Page 17: Debris Screen
22” Trimmer Mower Remove the spacer and wave washer between the left hand side wheel and the trimmer base. spacer See Figure 21. Slide the axle and wheel to the right. wave washer Figure 21 Debris Screen There is a debris screen over the cooling fan, the screen is necessary to prevent the cooling fins from get- Debris Screen ting clogged with trimming debris.The trimmer should not... - Page 18 Lift the locking tab from the slot on the engine cover. See Figure 23. Locking Tab Slot Figure 23 Starter Rope Slip the starter rope through the slot in the debris screen. See Figure 24. Slot Figure 24...
- Page 19 22” Trimmer Mower Push slightly on the back of the debris screen to unlock the rear tab from the engine cover. Lift the screen off of the engine. See Figure 25. Clear all debris from the screen and from the starter housing on the engine.
- Page 22 MTD Products Inc - Product Training and Education Department 769‐09540‐00 FORM NUMBER - 11/2013...
Need help?
Do you have a question about the remington and is the answer not in the manual?
Questions and answers