Table of Contents
Advertisement
Chapter 2 - Hardware Installation
Board Layout
Note:
SATA 0 supports SATA DOM.
DC-in
USB 3.0 0-1 Power
4-pin power (optional)
Select (JP8)
1
LAN 1
Intel
USB 0-1
WGI210AT
USB 3.0
1
USB 3.0 2-3 Power
Select (JP9)
LAN 2
USB 2-3
Mini PCIe Power
Mini PCIe
Select (JP7)
USB 3.0
1
12 10
Mini PCIe Signal
Select (JP6)
3
1
1
1
COM 3
COM 4
USB 5
2
10
2
10
USB 2.0 5 Power
DP 0-1
Select (JP11)
1
9
1
9
2
10
2
10
COM 1
1
9
1
9
COM 2
COM 1
(JP4)
RS232/422/485
(JP5)
1
2
Select
(JP3)
(JP4)
12
11
5
6
DP 2-3
1
2
(JP5)
LPC
5
6
1
2
(JP3)
2
1
5
6
1
System Fan
Chassis
1
Intrusion
1
2
1
Line-in
Front
Line-out
Audio
Mic-in
CPU Fan
9
10
S/PDIF
1
Realtek
ALC888
•
BE170 is not equipped with DC-in jack.
•
BE171: 12V DC-in jack (default) or 4-pin power connector (optional).
BE173: 19~24V DC-in jack (default) or 4-pin power connector (optional).
•
SATA power connectors are populated on BE171 and BE173 only.
•
24-pin ATX power connector is populated on BE170 only.
Chapter 2 Hardware Installation
Auto Power-on
Select (JP15)
SATA
SATA
SATA
SATA
Power 3
Power 2
Power 1
Power 0
13
1
4
1
4
1
4
1
4
1
SATA 3.0
SATA 3
SATA 2
SATA 1
Standby
SATA 0
Power LED
1
1
1
1
(JP15)
2
6
Battery
ATX Power
(JP14)
1
5
1
SMBus
1
SATA DOM Power
Clear CMOS
Select (JP2)
(JP12)
Data (JP1)
(JP13)
AMD
24
12
DIO Power Select (JP12)
DIO 0-3 Output State (JP13)
A77E
DIO 4-7 Output State (JP14)
SPI Flash
BIOS
USB 2.0 0-1/2-3
Power Select (JP10)
1
USB 2-3
USB 0-1
USB 2.0
4
USB 2.0
2
10
2
10
1
9
1
9
AMD
R-Series
Buzzer
PCIe x16
Chapter 2
Important:
Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in
boards, and other components. Perform installation procedures at an ESD workstation
only. If such a station is not available, you can provide some ESD protection by wear-
ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If
a wrist strap is unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
1 2
Front
Panel
1
System Memory
11 12
1
Digital
I/O
1
Important:
1
When the Standby Power LED lights red, it indicates that there is power on the sys-
1
Digital I/O
tem board. Power-off the PC then unplug the power cord prior to installing any de-
Power
vices. Failure to do so will cause severe damage to the motherboard and components.
Rear I/O
Onboard I/O
Storage
Expansion
Features
•
Two 204-pin DDR3 SODIMM sockets
•
Supports 1600/1866/2133MHz
•
Supports up to 16GB system memory
•
Supports dual channel memory interface
9
Standby
Power LED
DDR3-2
DDR3-1
www.dfi .com
Advertisement
Table of Contents
