Taking Temperature Measurements; Temperature Calibration Procedures - Hanna Instruments HI 98701 Instruction Manual

TAKING TEMPERATURE MEASUREMENTS

TAKING TEMPERATURE MEASUREMENTS TAKING TEMPERATURE MEASUREMENTS
TAKING TEMPERATURE MEASUREMENTS TAKING TEMPERATURE MEASUREMENTS
To prepare the instrument for use, choose the most appropriate tem-
perature probe(s) for your application (see accessories) and connect it
(them) to the connector(s) located on the top of the instrument.
The factory default thermocouple type is K, represented with the "dF"
indication. If needed, select a different type (J and T types also
available) through setup code 70.
With the meter facing you, channel #1 is the first connector on the
top left hand side.
Press the ON/OFF key to power on the instrument.
To take temperature measurements, insert the
probe in the sample to be tested and allow
the reading to stabilize. The temperature is
displayed on the upper LCD. The lower LCD
displays the selected channel number (HI98704 and HI98804 only).
The meter selects channel 1 as default. Press CH/
TIME (HI98704 and HI98804 only) or TEMP/TIME
(HI98701, HI98801 only) to view the reading of the
other channels, the cold junction temperature, date
and time in the following order:
• channel 2 temperature reading (4-channel versions only)
• channel 3 temperature reading (4-channel versions only)
• channel 4 temperature reading (4-channel versions only)
• cold junction temperature reading ( "C J" appears in the lower LCD)
• date
• time
Pressing CH/TIME or TEMP/TIME again, the meter returns to channel 1
temperature reading.
If the reading is out of range or the probe is
not connected to a channel, the LCD will
display a dashed line in place of the reading.
Note: To choose between "°C " and "°F" unit, enter the setup code 71.
Note: The meter is factory calibrated. After 1
year since last thermocouple calibra-
tion the "DATE" symbol starts blinking
on the LCD to warn the user that a recalibration is suggested to
maintain the accuracy of the meter. It is recommended that
recalibration is performed by authorized technical personnel
only. Contact your nearest HANNA service center.
14

TEMPERATURE CALIBRATION PROCEDURES

TEMPERATURE CALIBRATION PROCEDURES
TEMPERATURE CALIBRATION PROCEDURES TEMPERATURE CALIBRATION PROCEDURES TEMPERATURE CALIBRATION PROCEDURES
( ( ( ( ( for technical personnel only) for technical personnel only) for technical personnel only) for technical personnel only) for technical personnel only)
The meter is factory calibrated. However, as a general rule, it is
recommended to have all thermometers recalibrated at least once a
year. It is recommended that recalibration is performed by authorized
technical personnel only to assure the accuracy of the instrument.
Contact your nearest HANNA service center for a quick and accurate
annual recalibration.
Both thermocouple inputs and cold junction can be calibrated.
A two-point calibration at 0.000 mV and 41.269 mV has to be
performed in order to store the new thermocouple calibration data in
memory. Cold junction calibration is at one point only, corresponding
to the environment temperature.
COLD JUNCTION CALIBRATION
1. Press CH/TIME or TEMP/TIME until the cold junction temperature
reading is displayed.
2. Press ALT, CFM and PAPER simultaneously while the meter is not
printing nor logging to enter calibration mode.
3. User is prompted to enter password if it has been set to a value
different from 0000, otherwise skip to step 6.
4. Enter the password using the arrow keys.
5. Press ALT and CFM to confirm the password or CH/TIME or TEMP/
TIME to exit.
6. If password is correct or not set, the meter
will display "25.0°C" (or "77.0°F"), with
the "2" (or "7") blinking, on the upper
LCD and "C CJ" on its lower part; if
wrong, it will return to measurement mode without any message.
7. Enter the actual cold junction temperature (the environment tem-
perature measured with a reference thermometer) using the arrow
keys (temperature must be between 0 and 50 °C).
8. When the "S" symbol blinks in the lower
LCD, the reading is stable and calibration
can be confirmed pressing ALT and CFM.
9. The LCD will display CALC for a few seconds and then the meter
returns to normal operational mode.
15