Panasonic KX-TDA30 Getting Started
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. PBX
  5. KX-TDA30
  6. Getting started
Panasonic KX-TDA30 Getting Started

Panasonic KX-TDA30 Getting Started

Hybrid ip-pbx
Hide thumbs Also See for KX-TDA30:
Table of Contents

Advertisement

Quick Links

See also: Pc Programming Manual , Get Started
Thank you for purchasing the Panasonic Hybrid IP-PBX, KX-TDA30.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDA30: Version 1.0
Model no.

Table of Contents

........................................ 4
Hybrid IP-PBX
KX-TDA30
........................... 2
............. 11
............ 20
..... 14

Advertisement

Table of Contents
loading

Related Manuals for Panasonic KX-TDA30

Summary of Contents for Panasonic KX-TDA30

  • Page 1: Table Of Contents

    4 Customising the Hybrid IP-PBX ..14 5 Confirming the Connection .... 20 Thank you for purchasing the Panasonic Hybrid IP-PBX, KX-TDA30. Please read this manual carefully before using this product and save this manual for future use. KX-TDA30: Version 1.0...

  • Page 2: Before Installation

    Before Installation System Connection Diagram Hybrid IP-PBX for Digital Proprietary DLC8 LCOT4 Telephone (DPT) (KX-TDA3172) KX-T7636/ (KX-TDA3180) and DSS Console KX-T7633 Console Analogue Analogue Analogue DLC4 CID4 Trunk Trunk Trunk (KX-TDA3171) (KX-TDA3193) Telephone Company Voice ISDN BRI Line ISDN BRI Line ISDN BRI Line Processing (Digital Trunk)
  • Page 3 Unpacking Check the package contents. × Main Unit × CD-ROM (including manuals, etc.) × × × AC Cord* AC Adaptor Screw × × Mini Plug (for pager and Washer SD Memory Card × music source) × × Main Strap Optional Card Label Sheet * The type of the AC cord may vary depending on the country/area of use.

  • Page 4: Installation

    Installation Opening/Closing the Covers Opening the Covers Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable cover slightly to remove it. Slide Button Cable Cover Remove the three screws. Screw Holding the protrusions on both sides of the front cover, swing the cover open.
  • Page 5 Closing the Covers Close the front cover, then tighten the three screws. Screw Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the front hooks fit in place. Cable Cover Slide the cable cover down until it locks.

  • Page 6: Installing The Sd Memory Card

    Installing the SD Memory Card The SD Memory Card contains software for all the processes of the Hybrid IP-PBX and all the customer data. The SD Memory Card must be inserted before start up. SD Memory Card SD Memory Slot Cover Card CAUTION Do not remove the SD Memory Card during the operation of the Hybrid IP-PBX.
  • Page 7 Installing the Optional Service Cards Slot Position Slot s 10 and 11 supports only cards which do not have external ports. Therefore, these slots do not have removable cover plates. Slot 01 is the pre-installed super hybrid ports. No optional service card can be installed. Slot Condition The following table shows the slot condition.

  • Page 8: Caution

    Installing the Trunk/Extension Cards Before installing the optional service cards, cut and remove the appropriate dummy cover plates from the main unit. Dummy Cover Plate CAUTION For safety reasons, smooth the cut edges after removing the dummy cover plates. Position the card in the open slot, making sure that the tabs on the both sides of the card fit into place.

  • Page 9: Lcot4

    Installing the Trunk Cards LCOT4 Card RJ45 To trunk Accessory (included): Extension Bolt × 1, Strap × 1 User-supplied (not included): RJ45 connector or RJ11 connector* * The connector type may be RJ45 or RJ11 depending on the country/area. BRI2 Card RJ45 (LINE 1) RJ45 (LINE 2) To NT1...

  • Page 10: Connecting Extensions

    Installing the Extension Cards (DLC4/DLC8/SLC4/ SLC8) Example: DLC4 Card RJ45 To extension Accessory (included): Extension Bolt × 1, Strap × 1 User-supplied (not included): RJ45 connector or RJ11 connector* * The connector type may be RJ45 or RJ11 depending on the country/area. Connecting Extensions Example: KX-T7600 Series DPT Pin Assignments...

  • Page 11: Starting The Hybrid Ip-Pbx

    Frame Earth Connection IMPORTANT! Connect the frame of the Hybrid IP-PBX to earth. Loosen the screw. Screw Insert an earthing wire (user- supplied)*. Tighten the screw. Earthing Connect the earthing wire to earth. wire * For earthing wire, green-and-yellow To earth insulation is required, and the cross- sectional area of the conductor must be more than 0.75 mm...
  • Page 12 Set the System Initialise Switch to the "SYSTEM INITIALIZE" position. RUN Indicator Reset Button ALARM Indicator System Initialise Switch Plug the DC connector of the AC adaptor into the DC IN 1. Note The AC adaptor supplied with the Hybrid IP-PBX must be connected to the DC IN 1. If an AC adaptor is connected to the only DC IN 2, the Hybrid IP-PBX will not start.

  • Page 13: Getting Started

    Plug the AC cord into the AC adaptor, and then plug the other end into an AC outlet. AC Adaptor AC Cord To AC outlet Turn on the power switch. Power Switch Notes • For safety reasons, follow the procedures as indicated when turning on the Hybrid IP- PBX.

  • Page 14: Customising The Hybrid Ip-Pbx

    Customising the Hybrid IP-PBX KX-TDA30 Maintenance Console serves as an overall system programming tool for the Hybrid IP-PBX. KX-TDA30 Maintenance Console’s Quick Setup lets you easily configure the Hybrid IP-PBX to receive intercom and trunk calls, as well as apply basic settings such as time and date.
  • Page 15 Installing the KX-TDA30 Maintenance Console and Selecting Appropriate Country/Area Data For the system requirements of the PC (e.g., operating system, hardware specifications), refer to "7.3.1 Installing and Starting the KX-TDA30 Maintenance Console" in the Installation Manual. Note Screen shots reprinted with permission from Microsoft Corporation.
  • Page 16 Start the KX-TDA30 Maintenance Console from the start menu. a. Type the Installer Level Programmer Code (default: 1234). b. Click [OK]. Click "Connect" "USB" or "RS-232C" from the menu bar, depending on the serial interface connection with the Hybrid IP-PBX.
  • Page 17 The programme menu appears. Assigning the BRI Setting (Automatic Configuration) a. Double-click "Configuration". b. Double-click "Slot". c. Change the status of the BRI card to OUS. d. Click [Cancel]. Click "Tool" "BRI Automatic Configuration" from the menu bar. a. Click "Check" to turn on the BRI card. b.
  • Page 18 a. Type the Subscriber Number for the desired ports. b. Click [Execute]. ISDN line data such as P-P/P-MP, TEI Mode are automatically set. c. Click "Check Box" of the desired ports. d. Click [Data Apply]. e. Click [Close]. a. Double-click "Slot". b.
  • Page 19 For ISDN trunk user (MSN Setting): 1. Double-click "CO & Incoming Call". 2. Double-click "DIL Table & Port Setting". 3. Click the "DDI / DID / TIE / MSN" tab. 4. Set the "Incoming Type" of the desired ports to "MSN". 5.

  • Page 20: Confirming The Connection

    14. Double-click "Configuration". 15. Double-click "Extension Port". 16. Change the connection of the appropriate port to INS. 17. Click [OK]. Confirming the Connection Making Calls To call another extension extension no. Dial extension number. Talk. Off-hook. To call an outside party outside phone no.
  • Page 21 Getting Started...
  • Page 22 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan Copyright: This manual is copyrighted by Panasonic Communications Co., Ltd. (PCC). You may print out this manual solely for internal use with this model. Except above, you may not reproduce this manual in any form, in whole or part, without the prior written consent of PCC.

Table of Contents