Time Now Invisible Clock II Operation Instructions

Invisible Clock II Operation Instructions
® ® ® ®
To Start: Install a AAA battery in the back of your Invisible Clock.
The Invisible Clock-II has 7 modes, accessed by the Mode button:
Vibration and Beep adjustment (VIB & BEEP): Use to adjust Vibration Speed
•
(1 = low, 2 = medium, 3 = high), Beep Volume (1-3), Number of beeps (1-6).
Time and date adjustment (TIME & DATE): Use to set time and date.
•
Timer (TIMER SET): Use for simple timing or to repeat a time over and over.
•
12 Alarms (ALARMS SET): Use to set up to 12 alarms in a 24-hour period. Alarms
•
programmed in this mode will signal no matter what other mode the unit is in.
Meeting Timer (MEET-TIMER): Use for meetings, presentations or to track time
•
during any interval. The Meeting Timer vibrates at ½ way, at 5 minutes before time's
up, and at time's up, for any time interval set between 10 –120 min.
Custom Timer (CUSTOM TMR): Use to set any countdown time of up to 60
•
minutes, and program with up to six custom alerts to go off at any time in this period.
Can also set it to repeat, or count-up after countdown is complete.
Stopwatch (STOP-WATCH): use to count time for any event.
•
Please Read These Notes about Settings Protection:
1. Setting Protection – To protect the Timer, Meeting Timer and Custom Timer settings from erasure by accidental button presses, the
Invisible Clock-II has a "button auto-lock" feature (which engages automatically). To exit from the Timer or Meeting Timer you have
to press the two middle buttons simultaneously, and then press the Mode button to exit. To exit from the Custom Timer you only have
to press and hold the two middle buttons simultaneously for 2 seconds.
2. Setting Protection for Alarms - To protect the 12 Alarms from accidental erasure: Go to Alarms mode and press and hold the Enter
button for 3 seconds before you can enter the Alarms Mode before setting or changing any Alarm.
SETTING THE ADJUSTMENT & TIMING MODES
1. How to set Vibration Speed, Beep Volume and Number of Beeps.
Beep Volume (1-3), Number of beeps (1-6). (Factory settings are Vibration = 3; Beep volume = 3; Beep number = 3)
Time Date Time
VIB & BEEP VIBRATE 3
Advance to Vib
Enter Adjustment
& Beep Mode
mode
2. How to set the Time and Date
below on how to turn this feature on or off). (TIP: Hold Set button down to rapidly advance counting)
Time Date
5
:12
pm
TIME&DATE
SET TIME
Advance to Press twice,
Time & Date hours will blink
15
Time
9-
YEAR=2003
SET TIME
Advance to
Adjust Day
Year
3. How to use the Stopwatch
need the stopwatch to run while using other functions, stop it before leaving this mode.
Time SW Time
STOP-WATCH 0 : 00 : 00 : 00
Advance to
Enter mode
STOP-WATCH
Date Time Date Time
VIBRATE 1 BEEPVOL-2
Adjust Advance to beep
vibration volume
(The Invisible Clock-II will automatically adjust the time for daylight savings time; please see details
6
:12 6:
pm pm
SET TIME SET TIME
Advance to
Select hour
minutes
(note AM/PM)
Date Time Date
If you go past
YEAR=2003
the year you
want, continue
counting past
Select Year (do not
2040, to begin
push if correct year
again at 2003.
is shown)
(TIP: You can start the Stopwatch and then leave this mode and it will continue to count. If you do not
SW Time SW Time
0 : 00 : 01 : 35 0 : 00 : 24 : 32
Start Stop
Stopwatch Stopwatch
(settings protection engage automatically)
Date Time Date
BEEPVOL-3
Adjust beep
volume
12 15
pm6:
SET TIME
Adjust minutes
TIP:
Time Date
AYLSAV=T?
D
Hold for 3 seconds
to access daylight
savings time on/off
SW Time SW
0 : 00 : 00 : 00
Reset to zero
Time Now, Inc.
U.S. patent pending
Display
TIME
T I M E R S E T
Mode button Mode Enter
Enter button
To Exit from Timer and
Meeting Timer modes
push simultaneously, then
press Mode button to exit
Vibration Speed (1 = low, 2 = medium, 3 = high),
Time Date Time
BEEPNO #3 BEEPNO #4
Advance to Adjust number
number of beeps of beeps
8
-14
SET TIME SET TIME
Advance to Select month
month
Time Date
AYLSAV=on
D
ON = on
Press to turn
OFF = T?
daylight savings
time on or off
Time SW
0 : 00 : 37 : 21
Press while Stopwatch is
running to pause: Display
freezes, stopwatch still counts
Alarm Switch
Vibr=vibration
DATE
O = off
Beep = beep
Set Lite
Lite: Press
once and
stays on for
12 seconds
Set button
Hold down for
rapid counting
Date Time Date
VIB & BEEP
Press to save
settings
9 14
-14 9-
SET TIME
Advance to
day
Time Date
TIME&DATE
Press twice to
save all settings
Time SW
0 : 00 : 43 : 28
Press to resume
display of counting
after pausing