Motorola MT350PR User Manual

Body-Worn Operation
To maintain compliances with RF exposure guidelines if you wear a radio
®
on your body when transmitting always place the radio in a Motorola-
supplied or approved clip holder, holster, case or body harness for this
product. Use of non-Motorola-approved accessories may exceed RF
Two-Way Radio
exposure guidelines.
User Guide If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use position,
ensure the radio and its antenna are at least 1 inch ( 2.5 cm) from your
body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an
accessory cable, position the radio and its antenna at least one inch
( 2.5 cm) from the body.
Approved Audio Accessories
• 53724: Remote Speaker with Push-to-Talk Microphone
• 53725: Headset with Swivel Boom Microphone
• 53727: Earbud with Push-to-Talk Microphone
• 53728: Flexible Ear Receiver
• 56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies with
MTC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
MT Series
KEM ML34301 08
interference that may cause undesired operation.
Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn
off your radio in any facility where posted notices instruct you to do so.
Hospitals or health care facilities may be using equipment that is
sensitive to external RF energy.
For More Information
Aircraft
For more information, you may contact Motorola Solutions, Inc. at
When instructed to do so, turn off your radio when onboard an aircraft.
0-800-52-470
ny use of a radio must be in accordance with applicable regulations
per airline crew instructions.
Medical Devices – Pacemakers
The dvanced Medical Technology ssociation recommends that a
minimum separation of 6 inches (15 cm) be maintained between a
Safety and General Information
handheld wireless radio and a pacemaker. These recommendations are
consistent with the independent research by and recommendations of
Important Information on Safe and Efficient Operation
the U.S. Food and Drug dministration.
Read This Information Before Using Your Radio.
People with pacemakers should:
The information provided in this document supersedes the general safety • LW YS keep the radio more than 6 inches (15 cm) from their
information in user guides published prior to December 1, 2002. pacemaker when the radio is turned ON.
Transmit and Receive Procedure • Not carry the radio in the breast pocket.
Your two-way radio contains a transmitter and a receiver. To control your • Use the ear opposite the pacemaker to minimize the potential for
exposure and ensure compliance with the general population/ interference.
uncontrolled environment exposure limits, always adhere to the following
• Turn the radio OFF immediately if there is any reason to suspect that
procedure:
interference is taking place.
• Transmit no more than 50% of the time.
Medical Devices – Hearing Aids
• To receive calls, release the PTT button. Some digital wireless radios may interfere with some hearing aids. In the
event of such interference, you may want to consult your hearing aid
• To transmit (talk), press the Push to Talk (PTT) button.
manufacturer to discuss alternatives.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting (in Medical Devices – Other
terms of measuring standards compliance). If you use any other personal medical device, consult the manufacturer
of your device to determine if it is adequately shielded from RF energy.
Exposure to Radio Frequency Energy
Your physician may be able to assist you in obtaining this information.
Your Motorola two-way radio complies with the following RF energy
Safety and General Use While Driving
exposure standards and guidelines:
Check the laws and regulations regarding the use of radios in the area
• United States Federal Communications Commission, Code of Federal
where you drive, and always obey them. If you do use your radio while
Regulations; 47CFR part 2 sub-part J.
driving, please:
• merican National Standards Institute ( NSI)/Institute of Electrical
• Give full attention to driving and to the road.
and Electronic Engineers (IEEE) C95. 1-1992.
• Use hands-free operation, if available.
• Institute of Electrical and Electronics Engineers (IEEE) C95.
1-1999 Edition. • Pull off the road and park before making or answering a call if driving
conditions so require.
• International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1998. The use of a two-way radio while engaged in activities requiring
concentration may cause distraction or otherwise impair your ability to
• Health Canada - Safety Code 6; Limits of Human Exposure to
safely participate in such activities. lways use technology safely.
Radiofrequency Electromagnetic Energy in the Frequency Range
from 3 kHz to 300 GHz (2009).
Do not place a portable radio in the area over an air bag or in the air bag
deployment area. ir bags inflate with great force. If a portable radio is
• ustralian Communications uthority Radiocommunications
placed in the air bag deployment area and the air bag inflates, the radio
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
may be propelled with great force and cause serious injury to occupants
• N TEL NNEX to Resolution No. 303 of July 2, 2002.
of the vehicle.
• N TEL NNEX to Resolution No. 533 of September 10, 2009.
Potentially Explosive Atmospheres
To ensure optimal radio performance and make sure human exposure to
Turn off your radio prior to entering any area with a potentially explosive
radio frequency electromagnetic energy is within the guidelines set forth
atmosphere. Only radio types that are especially qualified should be
in the above standards, always adhere to the following procedures.
used in such areas as "Intrinsically Safe." Do not remove, install or
Portable Radio Operation and EME Exposure
charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
Antenna Care
even death.
Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could damage the Note: The areas with potentially explosive atmospheres referred to
radio and may violate MTC regulations.
above include fueling areas such as below decks on boats, fuel or
chemical transfer or storage facilities, areas where the air contains
Do NOT hold the antenna when the radio is "IN USE." Holding the
chemicals or particles (such as grain, dust or metal powders) and any
antenna affects its effective range.
other area where you would normally be advised to turn off your vehicle
engine. reas with potentially explosive atmospheres are often—but not
always—posted.
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
radio when you are near electrical blasting caps, in a blasting area, or in
areas posted "Turn off two-way radios." Obey all signs and instructions.
Operational Cautions Emergency Alert
Antennas
Volume
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn can
result.
Batteries
Push to Talk
ll batteries can cause property damage and/or bodily injury such as burns
if a conductive material—like jewelry, keys or beaded chains— touch
exposed terminals. The conductive material may complete an electrical
Call Tone
circuit (short circuit) and become quite hot. Exercise care in handling any
Flash Light
charged battery, particularly when placing it inside a pocket, purse or other
Button
container with metal objects.
Exercise care when removing NiMH or batteries. Do not use sharp or
Microphone
Mini-USB
conductive tools to remove either of these batteries.
Charging Port
Battery Charger Safety Instructions: (see menu Options)
Save these Instructions —
1. Do not expose the charger to rain or snow.
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the C cord or plug provided with the unit. If the plug will
not fit the outlet, have the proper outlet installed by a qualified
electrician. n improper condition can result in a risk of electric
shock.
Numbers for Channel,
4. To reduce the risk of damage to the cord or plug, pull the plug rather Call Tone
than the cord when disconnecting the charger from the C
receptacle.
Numbers for Codes
5. To reduce the risk of electric shock, unplug the charger from the
outlet before attempting any maintenance or cleaning.
6. Use of an attachment not recommended or sold by Motorola may
—Battery Meter
result in a risk of fire, electric shock or personal injury.
—Channel Power
7. Make sure the cord is located so it will not be stepped on, tripped
Indicator
over or subjected to damage or stress.
(see menu Options)
8. n extension cord should not be used unless absolutely necessary.
Use of an improper extension cord could result in a risk of a fire
—Keypad Lock
and/or electric shock. If an extension cord must be used, make sure
that:
—Talk Confirmation
• The pins on the plug of the extension cord are the same number, Tone (Roger Beep)
size and shape as those on the plug of the charger.
—Noise Filtering
• The extension cord is properly wired and in good condition.
• The extension cord size is 18 WG for lengths up to 100 feet, and
—On/Off for each
16 WG for lengths up to 150 feet.
feature
9. The supply cord of the C adaptor cannot be replaced. If the cord is
damaged, call customer service at 0-800-52-470.
Licensing Information
Weatherproof
Your radio channels operate within the Colectivo Familiar frequency use
This radio is weatherproof to IP-54 standards. It is dust/splashproof from
and is subject to MTC RVM 388-200-MTC/15.03. No license is required for
any direction. The radio is resistant to water and rain splashes only
use in Peru. Consult MTC Peru at www.mtc.gob.pe for more information.
when the battery cover and headset accessory mini-USB ports are
sealed. Open the battery compartment door or headset port cover only
Channels and Frequencies
when the radio is dry. Use of a headset accessory should be in dry
environments only.
The charging base and C adaptor are not waterproof. Do not expose the
Channel Frequency in MHZ Channel Frequency in MHZ charger to rain or snow. Charge the radios only in a dry location. Do not
place wet radios into the charging base. The battery door must be tightly
1 462.5625 8 467.5625
closed with the screw to maintain the weatherproof seal of the radio.
2 462.5875 9 467.5875
Installing the Batteries
3 462.6125 10 467.6125
Each radio can use either 1 NiMH rechargeable battery pack or 3
4 462.6375 11 467.6375
alkaline batteries and beeps when the batteries are low.
5 462.6625 12 467.6625
Installing NiMH Rechargeable Battery Pack
6 462.6875 13 467.6875
7 462.7125 14 467.7125 1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you. (The
ribbon should be underneath the battery pack and should wrap
around the right side of the pack for easy removal.)
5. Close the battery cover and tighten the retaining screw on the
battery door.
Installing the Three AA Alkaline Batteries ( Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
3. Insert the three
inside. (The ribbon should be underneath the
and should wrap around the right side of the batteries.)
4. Close the battery cover and tighten the retaining screw on the
Control Buttons
battery door.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
empty . When the radio has one segment left, the
radio chirps periodically or after releasing
Removing the NiMH Battery Pack
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the radio.
LED Indicator
4. Close the battery cover and tighten the retaining screw on the
Accessory Jack
battery door.
Removing the Three AA Alkaline Batteries ( Optional Accessory)
1. Turn the radio off.
Menu/ Keypad Lock
Scan/Monitor
MON 2. With the back of the radio facing you, loosen the retaining screw on
MENU
the battery door and open the cover.
Scroll
3. Gently remove each alkaline battery by easing each battery out
individually.
Speaker
4. Close the battery cover and tighten the retaining screw on the
battery door.
Notes
• Exercise care when removing NiMH or
Flash Light LED
sharp or conductive tools to remove either of these batteries.
Display Screen Guide
• Remove the batteries before storing your radio for extended periods
of time. Batteries corrode over time and may cause permanent
damage to your radio.
Using the mini-USB Charging Adaptor
The mini-USB charging adaptor allows you to conveniently charge your
NiMH battery pack. This is an alternative to charging your NiMH battery
pack in the Battery Charger desk stand using the C wall adaptor and
especially useful when used while traveling.
Available mini-USB charging options:
1. Vehicle charger
2. Mini-USB computer cable
—Vibrate
If using a computer, the computer must be turned on.
—Scan
This and other accessories (sold separately) are available for your radio.
—Dual Scan
For more information, visit our Web site at
—Call Tone, motorolasolutions.com/talkabout or shop.giantintl.com.
Keypad Tone
1. Plug your mini-USB cable or charger into a power source as is
appropriate for your accessory.
2. Plug the cable into the mini-USB port on the bottom of your radio.
—Hands-Free Use
3. fter the initial charge, an empty battery will be fully charged in 7 hrs.
Without
for the MT350 series radio (KEBT-650 m h NiMH battery pack) or 14
Accessories
hrs. for the MT352 series radio (KEBT-1300 m h NiMH battery pack).
—Hands-Free Use
4. The battery icon will scroll as the battery is being charged. The
With Accessories
scrolling icon will stop when the battery is fully charged.
Notes
• When moving between hot and cold temperatures, do not charge the
Getting Started NiMH battery pack until the battery temperature acclimates (usually
about 20 minutes).
• For optimal battery life, remove the radio from the charger within 16
hours. Do not store the radio while connected to the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
time for the battery to charge to 1 bar
transmit a message.
Attaching and Removing the Belt Clip
1. ttach belt clip to pocket or belt strap.
2. lign the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to release
the catch.
2. Pull the belt clip away from the back of the radio.
Using the Desktop Battery Charger ( Optional Accessory)
The battery charger provides drop-in charging convenience for NiMH
batteries and can be placed on any flat surface, such as a desk or
workbench. Charge the NiMH battery overnight (at least 16 hours) before
using it for the first time.
MT350R Radio
fter the initial charge, an empty battery (KEBT-650 m h NiMH) is fully
charged within 7 hrs.
MT352R Radio
fter the initial charge, an empty battery (KEBT-1300 m h NiMH) is fully
charged within 14 hrs.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the C power supply cord into the jack on the desk stand.
alkaline batteries with + and - polarity as shown
alkaline batteries 3. Plug the C power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging pockets.
5. When charging in the battery charger, the radio's backlight will
momentarily illuminate when placed in the charger.
6. The battery icon will scroll as the battery is being charged. The
scrolling icon will stop when the battery is fully charged.
to
Turning your Radio On and Off
(Low Battery lert). Turn clockwise to turn the radio on and counterclockwise to turn the
radio off.
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
2. The display screen then shows the current channel, code and all
features that are enabled.
Setting the Volume
Press and hold for three seconds, then rotate until you reach a
comfortable listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold .
batteries. Do not use
2. When you are finished talking, release .
For maximum clarity, hold the radio two to three inches away from your
mouth and speak directly into the microphone. Do not cover the
microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button
Pressing and holding for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows you to
adjust the volume, if necessary. You can also press to check for
activity on the current channel before you talk.
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio emits
a continuous warning tone and stops transmitting if you press
continuous seconds.
Menu Options
Selecting the Channel
Your radio has 14 channels. The channel is the frequency the radio uses to
transmit. Channels 1-14 are Colectivo Familiar 0.5 watt. (See the "Channels
and Frequencies" table for details.)
1. With the radio on, press . When the radio is on a 0.5
watt channel, displays.
2. Press or and select an unused or quiet channel.
3. Press to save the channel setting or to continue set up.
Selecting the Interference Eliminator Code
Interference Eliminator Codes help minimize interference by blocking
transmissions from unknown sources. Your radio has 121 Interference
Eliminator Codes. Codes 1 – 38 are the standard analog codes that
appear on other Colectivo Familiar radios. Codes 39 – 121 are additional
digital codes added for superior interference protection. 0 is the off
. llow
position, no analog or digital codes are enabled.
before attempting to
To set the code for a channel:
1. Press until the code starts to flash.
2. Press or to select the code.
3. Press to save the code setting or to continue set up.
You can set a different code for each channel using this procedure. n
extended press of or allows you to scroll through the Interference
Code rapidly so you can quickly reach the code you want.
Note: You must set the Interference Eliminator Code to 0 on a radio that
uses Interference Eliminator Codes to communicate with radios that do
not have Interference Eliminator Codes. Select 0 for "no tone, no code"
and OFF will flash on your radio's display.
Setting and Transmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. Your radio has 20 call tones
from which to choose.
To set a call tone:
1. Press three times until the current call tone setting flashes and
appears.
2. Press or to change and hear the call tone.
3. Press to set the new call tone or to continue set up.
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press .
Note: Setting the call to 0 disables the call tone feature.
Continued on back
for 60
MT Series