Page 1 Indication of the manufacturer and the importer in accordance with requirements of directive in accordance with requirements of directive in accordance with requirements of directive 2011/65/EU (RoHS) 2011/65/EU (RoHS) 2011/65/EU (RoHS) Manufacturer: K-Sun Corporation Manufacturer: K-Sun Corporation Manufacturer: K-Sun Corporation ® ® ® Address:...
Page 2 • To ensure compliance with the limits for a Class B digital device the enclosed interface cable should be used. (If Applicable) • Modifications or changes not expressly approved by K-Sun® Corporation could void the user’s authority to operate the equipment.
Page 3 -The adhered surface is damaged We shall not be liable for any damages, losses, costs, or expenses arising from these problems. • Do not carry out any operations not described in this manual, or K-Sun® GREEN MACHINE ® may break or cause injury.
Page 4: Using This Manual
Using This Manual About this manual This manual contains the following sections: Getting Started Describes preparations required before using K-Sun GREEN MACHINE ® . Basic Operations Divided into three sections. "Basic Operation 1" explains operations such as entering texts and attaching labels.
Page 5: Table Of Contents
● Rounding Off the Corners ....48 2.Entering texts (Example: NAME) ... 10 ® • Adjusting Display Level, Backlight . Length ......● Cleaning K-Sun GREEN MACHINE .. 49 3.Printing labels ........ 11 • Setting Display Language/Units ... Frame & Table ....
Page 6: Introduction
1.Preparation ........10 DISPLAY MESSAGES .... ● Rounding Off the Corners ....48 2.Entering texts (Example: NAME) ... 10 ® ● Cleaning K-Sun GREEN MACHINE .. 49 3.Printing labels ........ 11 To remove dirt and dust ● Attaching labels........11 PROBLEMS &...
Page 7: Important Safety Precautions
Items below should always be followed to protect users, their surroundings and their property from possible injury or damage. Be sure to read and understand the instructions before using your K-Sun® GREEN MACHINE ® and keep this manual handy for future references.
Page 8 If you do not use K-Sun® GREEN MACHINE ® for an extended period, take out the batteries from the device. Gas emitted from the battery may cause leakage, overheating, explosion, or damage to the device.
Page 9 Instructions K-Sun® GREEN MACHINE® follow the instructions on the battery GREEN MACHINE ® follow the instructions on the battery and the charger. and the charger. Risk of explosion if battery is replaced by an incorrect type.
Page 10 This may cut your fingers. Other Do not put anything heavy on K-Sun GREEN MACHINE ® or leave it K-Sun® GREEN MACHINE® in unstable position. This may cause injury or damage to the device.
Page 11: Tape Cartridges
Precautions when using tape cartridges ■ Do not drop or disassemble the tape cartridges. This may cause malfunction of the cartridges. ■ Do not pull or squeeze the label coming out of the exit slot. This may cause malfunction of the device. ■...
Page 12: General Cautions
K-Sun® GREEN MACHINE ® is powered, files or data stored on it may be deleted. ■ If your K-Sun® GREEN MACHINE ® is not to be used for long periods, remove the batteries, the bundled AC adapter, and tape cartridge from the main unit. K-Sun® GREEN MACHINE ®...
Page 13: Getting Started Ac Adapter
Getting Started This section describes how to connect the bundled AC adapter to your ® K-Sun GREEN MACHINE and turn the power on. If you are a first time user, it is recommended that you read this section first.
Page 15: K-Sun Green Machine
® K-Sun® GREEN MACHINE Parts Top side Tape verification window ® PeelGuard ® PeelGuard slot Display ® PeelGuard table ® PeelGuard guide USB Connection for PC models Internal parts Top cover Tape cartridge case Fixing tab Tape guide Tape eject slot...
Page 16: Bottom
Bottom Battery cover Cable guide Battery case Printer Back ® PeelGuard tray AC adapter connector Getting Started Getting Started...
Page 17 ® K-Sun® GREEN MACHINE Keys The functions of each key are described below. To perform the operation indicated by , hold down the key and press the specified key. (Print) (Telecom/Electrical Label Mode) Prints the text you entered on the tape, Enters the Telecom/Electrical Label Mode.
Page 18 Deletes the text to the left of the cursor. Cancels the current operation. (PC link) p.43 Switches the status so that the K-Sun® GREEN MACHINE ® can be connected (= Delete) to a computer. Deletes the texts or the paragraphs.
Page 19 (:<[{) Enters symbols. p.35 (+-=|) Enters symbols. p.35 (Cursor keys) Moves the cursor or highlighted items to up, down, right, or left. p.42 (= Cursor jump) Moves the cursor directly to the beginning of the paragraph/line or the end of the paragraph/line. When selecting items, shows the start or last option.
Page 20: Display Indicators
Display Indicators Display indicators <Text enter screen> 1 2 A B 1 2 A B Expand Euro Latin Reduce Caps Auto Cut Line head icon Cursor ( ) A movable indicator on a display, Appears on the line head to show the marking the position at which a character current line number.
Page 21: Switching Display (Graphic)
CapsLock indicator Auto cut indicator Lights when the key is pressed or Lights when "Auto Cut" is set to "On". when entering capital letters. Text size indicator Shows the text size of the line at the cursor position. Numbers from 1 through 5 correspond to inches as follows: 0.08"...
Page 22: Adjusting Display Level
Display backlight turns on/off by pressing the keys. The backlight helps you to clearly see the display. However, if you use the K-Sun GREEN MACHINE ® with alkaline or clearly see the display. However, if you use the K-Sun® GREEN MACHINE® with alkaline or...
Page 23: Setting The Display Language
The display language is set. The display language setting remains even after the power is turned off. To initialize the or reset the K-Sun® GREEN MACHINE ® . language setting, press "Resetting" (p.106) Setting the Display Units You can set the display units to inches or centimeters.
Page 24: Preparation
• K-Sun® GREEN MACHINE ® warranty does not apply to the AC adapter. 2. Installing the batteries Your K-Sun® GREEN MACHINE ® also works with batteries when an electrical outlet is not available. Six AA alkaline batteries or nickel-hydride rechargeable batteries (The SANYO eneloop HR-3UTGA or HR-3UTGB are the only tested and approved rechargeable batteries for use in the K-Sun®...
Page 25 HR-3UTGA or HR-3UTGB are the only tested and approved rechargeable batteries for use in the K-Sun® GREEN MACHINE ® .). Other types of batteries cannot be used. • Even though you can print only with the battery power, it will shorten the battery life. To minimize the battery consumption, always use the AC adapter whenever using the K-Sun®...
Page 26 HR-3UTGA or HR-3UTGB are the only tested and approved rechargeable batteries for use in the K-Sun® GREEN MACHINE ® will supply enough power for the device to print on one tape cartridge (0.7" x 26') at room temperatures. However, when you operate the device in cold places or print on wide tapes, the life span of the batteries becomes shorter.
Page 27: Installing Tape Cartridges
• Make sure that the power is turned off beforehand. • Do not open the top cover further than that angle in the right figure, or the cover may come off and the K-Sun GREEN ® MACHINE will be damaged.
Page 28 • When installing the tape cartridge, insert it firmly as far as it can go. • When the tape cartridge that is not supported by the K-Sun® GREEN MACHINE ® is installed, a message; "Check Tape!" or "No Tape!" appears. Reinstall the supported tape cartridge properly.
Page 29: Turning The Power On
See "Display Indicators" (p.14). Auto power-off If there is no activity for approx. five minutes, the K-Sun® GREEN MACHINE ® automatically shuts down in order to save battery power. (Text you have entered remains.) Press key again to restore.
Page 30: Feeding The Tape
5. Feeding the tape After installing the tape cartridge, make sure to feed the tape so as to take up the slack of the tape. Hold down the key and press (= Feed/Cut). Feed/Cut menu appears. Press keys to select "Feed & Cut" or "Feed".
Page 31 Supply Cartridge Reference Guide...
Page 32 SUPPLY CARTRIDGES ORDER NO. SIZE INK COLOR TAPE COLOR FABRIC TAPE CARTRIDGES - 16’4” 209FBB 3/8” BLACK BLUE 209FBP 3/8” BLACK PINK 212FBB 1/2” BLACK BLUE 212FBP 1/2” BLACK PINK SHRINK TUBE CARTRIDGES - 96” length ORDER NO. SIZE INK COLOR SHRINK TUBE COLOR 203STBW...
Page 33 SUPPLY CARTRIDGES Labeling Tape Cartridges All tapes cartridges 26 feet unless noted. ORDER NO. INK COLOR TAPE COLOR 1/6” 4MM Width 204BW BLACK WHITE 1/4” 6MM Width 206BC BLACK CLEAR 206BW BLACK WHITE 206BY BLACK YELLOW 206WB WHITE BLACK 206BG BLACK GREEN 206BB...
Page 34 1/2” 12MM Width - 26’ unless otherwise indicated 212BC BLACK CLEAR 212BW BLACK WHITE 212BY BLACK YELLOW 212WB WHITE BLACK 212BB BLACK BLUE 212BR BLACK 212BG BLACK GREEN 212WR WHITE 212WG WHITE GREEN 212WL WHITE BLUE 212GC GOLD CLEAR 212WC WHITE CLEAR 212GB...
Page 35 3/4” 18MM Width - 26’ unless otherwise indicated 218BC BLACK CLEAR 218RC CLEAR 218WC WHITE CLEAR 218BW BLACK WHITE 218BY BLACK YELLOW 218RW WHITE 218WB WHITE BLACK 218BX BLACK GRAY 218BB BLACK BLUE 218BR BLACK 218BO BLACK ORANGE 218BG BLACK GREEN 218BV BLACK...
Page 36 1” 24MM Width - 26’ unless otherwise indicated 224BC BLACK CLEAR 224BW BLACK WHITE 224BY BLACK YELLOW 224WB WHITE BLACK 224BB BLACK BLUE 224BR BLACK 224BG BLACK GREEN 224WR WHITE 224WO WHITE ORANGE 224WG WHITE GREEN 224WL WHITE BLUE 224SM BLACK SILVER MATTE, 16’4”...
Page 37: Basic Operations 1
Basic Operations 1 - Creating basic labels - ® This section describes K-Sun® GREEN MACHINE basic operations. You will learn how to enter text, print, and create simple labels.
Page 38: Entering Text
1. Entering text To enter text in capital letters or insert characters written on the keyboard keys in green, you need to use the key. You are entering this text. Enter "Television". Enter "T" in capital letter and then "elevision" in a small letter using the character keys.
Page 39 REFERENCE Entering Euro/Latin characters You can enter european and latin characters by pressing key when a character replaceable with an european or latin character is entered. : Enter "Televisión". Enter "Televisi" and then "o". • See "Euro/Latin Character List" for Press key several times available characters.
Page 40: Inserting Space
REFERENCE Two-byte space With the K-Sun® GREEN MACHINE ® , you can select the size of the space from one byte or two byte. Size of a two-byte space equals to approximately the size of two characters combined.
Page 41 Press key. • Refer to appendix for the symbols and pictographs can be input. "Symbol List" (p.121), "Pictograph List" (p.123) • To cancel the operation, press, keys. • A menu or a symbol you selected comes at the head of other options from the next time (learning function).
Page 42: Viewing Print Image (Preview)
4. Viewing print image (Preview) K-Sun® GREEN MACHINE ® can display the print image of the label on the screen so that you can check the image before you actually print the label. This feature prevents possible misprint and tape waste.
Page 43: Printing Label
(characters or the style). The number is counted up to "100", then returned to "1". • When "Margin" is set to "Minimum", "Short", or "Tape width 1/3", the K-Sun® GREEN MACHINE ® cuts the left margin off before starting to print. When "Margin" is set to "Middle", "Long"...
Page 44: Attaching Label
We shall not be liable for any damages, losses, costs, or expenses arising from these problems. • Your K-Sun® GREEN MACHINE ® is equipped with PeelGuard ® which rounds off the corners of the labels. See "Rounding Off the Corners" (p.48).
Page 45: Turning The Power Off
• Powering off message is displayed while turning off the K-Sun® GREEN MACHINE ® . Do not remove the AC adapter until the message disappear. • If your K-Sun® GREEN MACHINE ® is not to be used for long periods, remove the batteries, the bundled AC adapter, and tape cartridge from the main unit.
Page 46 Basic Operations 1...
Page 47: Basic Operations 2
Basic Operations 2 - Creating labels for various purposes - In this section, you will learn to create the labels with multiple lines or paragraphs so that you can arrange the layout as you like. You will also learn how to round off the corners of the labels.
Page 48: Editing Text
Editing Text You can edit the text by inserting or deleting characters. Using the cursor keys A vertical line " " appears on the display is called cursor. The cursor indicates the position at which a character can be entered or deleted. Press the cursor keys to move the cursor.
Page 49: Deleting/Inserting Text
• In order to change all the settings to their default, you need to initialize your K-Sun® GREEN MACHINE ® . "Resetting K-Sun® GREEN If the total number of the characters MACHINE ® " (p.105).
Page 50: Adding New Lines (Line Break)
Maximum number of lines K-Sun GREEN MACHINE ® supports tape cartridges ranging from 1/6" to 1" of width. Number of lines you can enter varies depending on the width of the installed tape cartridge.
Page 51: Moving The Text To The Next Line
Moving the text to the Joining the two lines next line Move the cursor to the right of the line head icon to move the text to the upper When you insert a line break in the middle line. of the text, the characters to the right of :Joining the two lines.
Page 52: Starting A New Paragraph
column Adding New Paragraphs [ The label below consists of two blocks. Each block is called paragraph in this manual, and each paragraph is made with a group of lines or a single line. By dividing a text into several paragraphs, you can change the number of lines or the style of the text on a paragraph-by-paragraph basis.
Page 53: Dividing Into Paragraphs
Dividing into paragraphs When you divide a text into paragraphs, the text at the right of the cursor moves to the next paragraph. :Adding a new paragraph. Paragraph 1 Paragraph 2 Start a new paragraph at the right of " " in paragraph 1. Paragraph 1 Paragraph 2 Move the cursor to the right of "...
Page 54: Rounding Off The Corners
Rounding Off the Corners - PeelGuard ® ® ® Your K-Sun® GREEN MACHINE includes PeelGuard ‚ that allows you to round off the corners of the labels. This feature lets the labels look better and prevents them from being peeled off.
Page 55: To Remove Dirt And Dust From The Exterior
® Pull out the PeelGuard tray as shown in the figure below. ® • The K-Sun® GREEN MACHINE have paper dust in the tray. This is because of the inspection carried out during the production process. ® • When you use the PeelGuard over the ®...
Page 56: Cleaning The Print Head (Faint Printing)
Cleaning the print head (faint printing) ■ When the printing becomes faint Printing becomes faint when dirt or dust adheres to the printhead. Rub the printhead with a cotton swab moistened with medical alcohol (isopropyl) available in the market. A faint streaking Basic Operations 2...
Page 57: Telecom/Electrical Label Mode
Telecom/Electrical Label Mode - Printing label for cables - In this section, you will learn how to create labels that wrap around a cable, wire, tube, pen or any other round-shaped materials.
Page 58 Flag) that allow you to easily create labels to be attached to a round-shaped material such as a cable, wire, and tube, and to neatly label panels, power strips and other communication equipment. You can easily access any one of the functions by just pressing the corresponding key.
Page 59 The following describes the feature of each functional mode. ● Mode of "Patch Panel" You can print multiple words in a single label specifying a space between the words. Panel B Patchpanel A For use when printing equal text data and you need to sequence either a number or : For attaching to a 3-outlet power strip.
Page 60: Creating The Label In Telecom/Electrical Label Mode
● Mode of "Wrap" ● Mode of "Wrap" A label to wrap around a cable can be made. Labels can be made to wrap around cables in two directions: vertical or horizontal. A label to wrap around a cable can be made. The horizontal feature is for use with the 224SL Self-Laminating Overwrap Tape.
Page 61 Characters can be printed in both horizontal and vertical. ● Mode of "Flag" A flag label can be made. Attach a cable to the cente Characters can be printed in both horizontal and verti ● Mode of "Flag" A flag label can be made. Attach a cable to the center of the label and fold the label in half. ●...
Page 62: List Of "Telecom/Electrical Label Mode" Menu
Telecom/Electrical Guide Character Settings* Maximum Maximum Recommended number of number of tape width PatchPanelA Patch panel A 10 sequence 20 per labels 1/6" to 1" 1 label PatchPanelB Patch panel B 1 label 1/6" to 1" Wrap Vert. Wire wrap 10 lines 8 per line 3/8"...
Page 63: Additional Functions
Additional Functions ® - Using K-Sun GREEN MACHINE freely and creatively - ® This section describes how to make better use of the function keys. You will learn to change the orientation of the label, improve the appearance of the label, and save the entered text.
Page 64: Changing The Font Type
Changing the font type Using To select the font you want to use, press key. The fonts appear in the following order. SansSerif SansSerif.HG SansSerif.ST Gothic BoldGothic Roman US Roman CL Roman Mincho Gyosho Reisho Script PL Back to SansSerif Press key repeatedly until the font you want appears.
Page 65: Using The Decoration Functions
Improving the Appearance of the Label Edit Key Functions Improving the Appearance of the Label - Using the decoration functions - - Using the decoration functions - Improve the appearance of the label by changing the font and the size of the texts. To change the appearance of the label press key, then select a function from the Improve the appearance of the label by changing the font and the size of the texts.
Page 66: Setting Functions
Setting functions Functions can be set through the following procedure: Place the cursor. When applying the function to a whole line or a paragraph, place the cursor in the line or paragraph respectively. When applying the function to the entire text, place the cursor anywhere within the text. "Effective area and the position of the cursor"...
Page 67 ● Setting the Decorate, Space, Frame & Table, Wide & Narrow,Bold & Italic and Font type Label Applies the selected style to the whole text (nothing changes on the text screen). Characters (Text mode change icon) is displayed where the cursor is placed, the selected mode applies from the characters after until the end of the text (or until the next...
Page 68: List Of Edit Menu (English)
List of Edit menu (English) The default setting is indicated by Bold Menu Menu1 Menu2 Number setting Length Left Number setting Center 1.0" Length You can specify the Right length of the label. p.65. 15.0" Left Mini DV　　MD　 Music tape Disk case Center Binder Right...
Page 69 Menu Menu1 Menu2 Space Normal Wide Space You can adjust the Narrow inter-character spacing. None "Proportional = On" sets the characters proportionally, whereas "Proportional = Off" sets the characters to full size. p.68. Border & Line Doubleline Underline Border Border & Line You can set underline, RoundBord.
Page 70 Menu Menu1 Menu2 Equal Line size 1 Line Equal You can set the same text size for each line. p.72. 2 Lines Auto format You can set the text size of each line to be displayed as a combination of pictographs.
Page 71: Function Description
Function description ● Length Sets the lengths of the label to be printed. After setting the length, select the position of the characters on the label. Check the position using the displayed pictographs. Set the length of the label between 1.0" and 20.0" using numbers.
Page 72 ● Frame & Table Surrounds the text (paragraph) with frames or inserts tables. Off (default) No frame or table is inserted. Table Surrounds the text (paragraph) with a frame and inserts a horizontal separation line in between the lines. When setting the same table in several paragraphs, inserts a separation line between the tables.
Page 73 (If you use 1" width tape, the margin will be 1".) • When "Margin" is set to "Minimum", "Short", or "Tape width /3", the K-Sun® GREEN MACHINE ® cuts the left margin before starting to print. When "Tape width" is set to "0.16""...
Page 74 ● Decorate Selects the text decoration. Out line Normal Shadow S + O (= Shadow + Out Line) Characters may be distorted due to character size or a high number of strokes. ● Space Sets the inter-character spacing. Normal Wide Narrow None Then, select the proportional from "On"...
Page 75 Setting "Space" • Selecting "Narrow", may have no effect on characters that are pre-designed minutely. • When creating a logo with attached expanded characters, selecting "Narrow" will print a label with perfectly attached characters. "Using User's Symbols" (p.94) • You can create eye-catching labels by decreasing the inter-character spacing of large characters or increasing the inter-character spacing of small characters.
Page 76 ● Bold & Italic Changes the text in bold or italic. Italic Normal Bold Bold & Italic Some characters may be distorted when applying both decoration settings and small size. ● Vertical The orientation of the label can be changed to vertical or horizontal by sentence or paragraph Horizontal label Vertical label Press...
Page 77 REFERENCE Printing two-digit numbers vertically The two-digit setting handles double figured numbers as one character. Select the "Double Figure" setting to align and print dates, house numbers of addresses, etc. when using the vertical orientation. : Enter "06 Diary". Change the label orientation Input "06"...
Page 78 ● Line size Changes the size of the texts. Set the text size using "Equal" or "Auto format". key. See "Changing the font/text size" (p.58). The Line size also can be changed by Equal Sets a equal text size for each line. (default) 0.5"...
Page 79 • The auto format is represented using pictographs. • The text size of each line differs depending on the width of the tape and can be checked on the text size indicator. • If the number of set lines and the number of lines input differs, "Equal" will be used to print. ●...
Page 80: Printing Sequence Numbers
Printing sequence numbers To create multiple labels with same texts and different numbers or characters, use the The Green Machine allows you to sequence numbers (up to any 2 digits) and/or the ® "Sequence" feature described below. The device automatically increases the numbers A-Z alphabet.
Page 81 Printing sequence numbers To create multiple labels with same texts and different numbers or characters, use the …CONTINUED "Sequence" feature described below. The device automatically increases the numbers or characters every time it prints a label. For this example we are going to create and print sequenced labels one at a time. To print sequence numbers set the initial value and the number of repetitions (1, 2, 3, 4, 5, 10 times).
Page 82: Creating A Label With A Bar Code
Printing Bar Codes Hold down key and key to insert bar codes. The default setting is indicated by Bold Creating a label with a bar code Menu4 Menu Menu1 Menu2 Menu3 Bar Code CODE128 Width (CODE 39, ITF, (CODE 39, ITF, Small Bar Code CODE 39...
Page 83 : Printing an "ITF" bar code (Width = Large, Ratio = 3.0, C/D on) Enter the bar code number using Press key while holding down the character keys. key . Select "ITF" and press key. The number will be displayed. The check digit is automatically displayed in the shaded field in the right upper corner.
Page 84 • To cancel the process press keys. This takes you back to the previous step. • A single label can have up to three bar codes and one sequence number or letter but bar codes can not be sequenced. • Bar codes contain considerable data, and use up a lot of memory when saved in files. •...
Page 85: List Of "Extra Print" Menu
Extra Key Print Functions Pressing key allows you to set special printing functions such as continuous and enlarged printing. List of "Extra Print" menu The default setting is indicated by Bold Menu Menu1 Menu2 Enlarge print print Enlarge 2 size ✕...
Page 86: To Create A Label That Is Wider Than The Width Of The Tape (Enlarge)
To create a label that is wider than the width of the tape (Enlarge) Enlarged printing enlarges the label 2 to 6 times, and divides the label into sections to be printed so that you can create a label that is bigger than the width of the tape. Assemble the completed label before using it.
Page 87 : Enlarging a label 3 times and printing it. Once the text is entered press Select "Execute?" and press keys. key. The "Extra Print" menu will be displayed. Select "Enlarge print" and press key. The 3 sections of the label set are printed.
Page 88 • You can cancel the process by pressing keys. • The enlarged printing is not available for the label created in "Telecom/Electrical Label Mode". • When assembling a label that was created using "Enlarge", the label may not align completely. •...
Page 89: Prints The Same Label Continuously (Repeat)
Prints the same label continuously (Repeat) Prints a specified number of identical labels continuously. : Printing the same label 3 times continuously Enter the text and press key. Select "Execute?" and press key. The" Extra Print" menu will be displayed. Select "Repeat"...
Page 90 • You can cancel the process by pressing keys. This will take you back to the • You can cancel the process by pressing keys. This will take you back to the previous step. Repeating this procedure allows you to go back to the text enter screen. previous step.
Page 91: Mirror Printing
Mirror printing Prints the label in mirror image. Enter the text and press key. The" Extra Print" menu will be displayed. Extra print is executed only when the "Print exec?" is selected from "Extra print". Select "Mirror print" and press key is not used for the extra print key.
Page 92 Print setting Functions Pressing key while holding down key allows you to set special printing functions such as continuous and enlarged printing. List of "Print setting" menu The default setting is indicated by Bold Menu Menu1 Print density Print density Sets the print density.
Page 93 Replacement is performed at your expense. • Autocut settings are not initialized when the machine is turned off. Use this procedure to correct settings, reset the K-Sun® GREEN MACHINE ® initialize the machine. "Resetting" (p.88) "Resetting K-Sun®...
Page 94 Resetting Press key while holding down key. The "Print setting" menu will be displayed. Chose "Memory reset" and press key. Press key. The setting you made to the "Auto cut" and "Print density" is canceled and returned to the default settings.
Page 95: Saving A File
Saving a file Press key while holding down keys to select a key. document number and press key. Select "Store", and press key. The "Store" menu will be displayed. Check the information to be saved and press key. "Execute" is displayed, then the screen will return to the text screen after saving.
Page 96 Recalling a file Recalls the saved text on the text screen. Files can be loaded using "Replace" or "Connect". If "Replace" is selected, the current content of the text enter screen will be deleted and replaced with the text of the loaded file. If "Connect" is selected, a new paragraph with the loaded text will appear immediately after the paragraph containing the cursor.
Page 97: Deleting A File
Deleting a file Press key. Check the information and press "File" menu will be displayed. key. to confirm the text. Select "Recall", and press key. Files deleted. keys to select the text to be deleted and press key. Once you delete files, they cannot be restored.
Page 98 (five) may called and press key. be less because of the capacity of the K-Sun GREEN MACHINE ® . Also, the print history may not be remained depending on the status of the label. • key does not work if there is a blinking character on the display.
Page 99 Deleting the print history Press keys. "File" menu will be displayed. Once you delete the print history, it can not Select "Print history" and press be restored. key. • key does not work if there is a blinking character on the display. •...
Page 100 Using User's Symbols Saving marks and company logos that you have designed yourself, or external characters and symbols as user's symbols allows you to insert and print them. User's symbols are square. Horizontally long logos are divided and stored as several "...
Page 101 Drawing method (Select using the menu screen area) keys to select a drawing method. Select an option among 1 dot filling "Rvrs", block filling "On", or block filling "Off (= Delete)". Menu Drawing method Menu Press In the menu, "1 Rvrs" is highlighted. Move the cursor to the dot to be filled using keys.
Page 102 Creating and saving user's symbols " 2 ". : Saving " " as user's symbol Press key. Once the 16-dot symbol has been "Symbols" menu will be displayed. drawn press key. Select "User's Symbol", and press The 16-dot data is automatically key.
Page 103 Modifying user's symbols Loading a user's symbol : Modifying the 48-dot data for the Press key. " 2 ". user's symbol Press key. Select "User's Symbol" and press key. Select "User's Symbol", and press key. Select "Recall" and press key. Select "Modify"...
Page 104 Copying a user's symbol Copies a user's symbol to a different user's symbol number. Press key. Check the information and press key. Select "User's Symbol", and press key. Select "Copy" and press key. Copying is executed. • You can cancel the process by pressing keys, select the original keys.
Page 105 Deleting a user's symbol Copies a user's symbol to a different user's symbol number. Press key. Once you delete a user's symbols, they Select "User's Symbol", and press cannot be restored. When the symbols you key. delete are printed, they will be a blank character on the label.
Page 106 Creating and registering a user's symbol from a reference symbol Creating a user's symbol using a reference character or symbol supported by this machine. ● Registering a reference character ● Modifying a reference character Recall the text character (symbol) and To create a user's symbol recall the text modify the 16-dot character.
Page 107 Modify the data. Modify the data based on the 16-dot reference character that will be displayed. Press key to display the next size revision screen. "Screen mode and drawing method" (p.94). Press key once the 48-dot drawing is complete. A message reading "Execute" will be displayed. Once the character has registered the text enter screen will be displayed again.
Page 108 To initialize the battery setting, just select "Alkaline" in the step 3 ® or reset the K-Sun® GREEN MACHINE keys, select "Nickel- • See "Resetting" (p.106). hydride" and press key.
Page 109: Key Functions
Setting Default Settings Default settings for items such as "Font" and "Space" can be changed. The following functions can be set using key. Key functions Functions that can be set Length,Lines, Vertical, Layout, Frame/Table,Font, Decorate, Space Selecting a function displays the item menu list. The selected item is the default setting. If you often use different "Font", etc.
Page 110 Changing Default settings Select the option you want to set Delete all the text by pressing as default setting and press key while holding down key. You need to delete all text before changing default settings. "Deleting all the text" (p.43). Press while holding down Set each item using the same method...
Page 111: Print History
® Resetting K-Sun® GREEN MACHINE ® • K-Sun® GREEN MACHINE , is an electronic device and therefore may sometimes stop working as a result of static electricity or other causes. • If the display is distorted and the machine has stopped responding, the ON/OFF key does not work, reset the machine through the following procedure.
Page 112 Resetting Press key and turn the power off. If the machine does not turn off when pressing key, unplug the AC adapter and remove the batteries. Plug the AC Adapter again or install the batteries and press key again. Power is restored. Press key while holding down key.
Page 113 Appendix...
Page 114: User's Symbols
List of "Symbol" menus (English) Bold Press to enter symbols. The default setting is indicated by See the "Symbol List" for more symbols displayed in each menu. "Symbol List" (p.121). Menu First option Parenthesis Select the symbol. Symbol Arrows Units Math Abbreviation Mark...
Page 115 List of "Pictographs" menus (English) Bold Press to enter symbols. The default setting is indicated by See the "Pictographs List" for more symbols displayed in each menu. "Symbol List" (p.121). Menu First option ANSI Select the symbol. Pictographs Bio-Chemical Electrical Environment Packages Warnings...
Page 116 The tape cartridge is not installed or not installed correctly. Turn the power off and reinstall the tape cartridge correctly. "Installing tape cartridges" (p.21). Tape cartridge that is not supported by the K-Sun® GREEN ® MACHINE , is installed, or the cartridge is installed incorrectly.
Page 117 Error message Cause and Remedy The text you entered is too long to fit within the specified length. Press any key to return to the text enter screen and perform the following remedies: • Delete some characters • Reduce the font size You can also press to continue printing or previewing regardless of the set length.
Page 118 If there is no activity for approx. five on/off the power, or a similar malfunction ® occurs, you need to reset the device. minutes, the K-Sun® GREEN MACHINE "Resetting" (p.106). automatically shuts down in order to save battery power (auto power-off).
Page 119 AC adapter that comes with the device, ® You cannot print while using the ® otherwise the K-Sun® GREEN MACHINE PeelGuard® trimmer may turn off in the middle of the operation or during printing. Text is not printed "Setting battery type"...
Page 120 "Setting battery type" (p.102). ● Trying to trim unsupported tape? Contents of files are Be sure to use the tapes supported by the K-Sun® GREEN MACHINE ® . gone "Rounding Off the Corners" (p.48). ● Has the device initialized? ●...
Page 121 You cannot attach labels ● Is the backing sheet removed? Peel off the backing sheet of the adhesive tape to attach. "Attaching label" (p.38) ● Are you attaching labels to clean and flat surface? Labels may peel off easily or not adhere well when attached to oily, dusty, or rough surfaces.
Page 122: Character Table
List of Characters Key layout Character table Character Character When When When When pressed pressed pressed pressed singly with then [Key] singly with then [Key] & Appendix...
Page 123 List of Input normal text Press ’ " < > Press keys (Minus) (Dash) (Under bar) Input barcode ● Code 128 Press ’ " < > Press keys (Minus) (Under bar) ● Code 39 Press (Minus) Press keys (Minus) ● CODABAR Press (Minus) Press...
Page 124 Thin film thermal head (180 dpi, 128 dot) Tape width detect Detects P tape standard holes (7 types) ® Tape cartridge Use K-Sun® LABELShop Tape Mark One-time tape cartridge that prevents reversal and slack Wear-resistant PRO mechanism 0.16", 0.2", 0.4", 0.5", 0.7", and 1"...
Page 125 ■ Print functions Seven character sizes Text Size 16 dot ✕ Text Size 24 dot ✕ Text Size 32 dot ✕ Text Size 48 dot ✕ Text Size 64 dot ✕ Text Size 96 dot ✕ Text Size 120 dot ✕...
Page 126 ■ Power Supply AC 120 V (Bundled Adapter Model AST116Y1‐1) must be used Main power AST1116Y1-1 (Bundled AC adapter must be used) Sub battery (6) AA Alkaline Batteries Manufacturer: K-Sun Corporation Or Input AC 100-240V, 0.4A, 50-60 Hz (6) Nickel‐hydride rechargeable batteries** ■ Power Supply (dedicated adapter, power cable only) **Use only K‐Sun approved rechargeable batteries: Output DC 11V, 1.64A ...
Page 127 Symbol List • Images in the "Symbol List" may differ from actual ones of printed label. Category Symbol Parenthesis Arrows Units Math Abbreviation Mark Number DoubleFigure 00-99 ’+DoubleFigure ’00-’99 Europe...
Page 128 Category Symbol LatinAmerica Greek Cyrillic...
Page 129 Pictograph List • Images in the "Pictograph List" may differ from actual ones of printed label. Category Symbol ANSI Bio- Chemical Electrical Environment Packages Warnings Public Signs Shop Construction...
Page 130 Hospital Work Sports Vehicles Miscellaneous...
Page 131 Frame and Table List • Frame images in the "Frame and Table List" may slightly differ from actual printout. Table Frame...
Page 132 Euro/Latin Character List ® The K-Sun® GREEN MACHINE allows you to enter the following characters. Basic Replaceable Basic Replaceable Alphabet Characters Alphabet Characters à á â ã ä å æ ā À Á Â Ã Ä Å Æ Ā Ă Ą...
Page 133 List of menu :Telecom/Electrical Label English Menu Menu1 Menu2 Menu3 Panel PanelA Length Patch panel A Label 1 [ 1.0" 5.0" PanelB Length Patch panel B Label 1 [ 1.0" 5.0" Wire wrap Wrap Vert. Length Line 1 [ 1.0" 5.0"...
Page 134 List of menu :Edit English Menu Menu1 Menu2 Number setting Length Number setting Left Center 1.0" Right 15.0" Mini DV　　MD　 Left Music tape Disk case Center Binder Right 　 Frame & Table Table Frame "Frame and Table List" (p.125) Margin Short 3mm Minimum 1mm Middle 10mm...
Page 135 Menu Menu1 Menu2 Wide & Narrow Smaller Small Narrow Normal Wide Background 1 Wave 2 Diamond 3 Cherry 4 Card 5 Arabesq. 6 Mesh 7 Dot Bold & Italic Italic Normal Bold BoldItalic Vertical Equal Line size 1 Line 2 Lines 3 Lines 1/11 2/11...
Page 136 List of menu :Extra Print English Menu Menu1 Menu2 Enlarge print 2 times 3 times 4 times 5 times 6 times Repeat print Set number Repeat number Until stop Mirror print Print exec? English...
Page 137 List of menu :Bar code English Menu4 Menu Menu1 Menu2 Menu3 Bar Code CODE128 Width Small (CODE 39, ITF, (CODE 39, ITF, CODE 39 CODABAR) CODABAR) Medium Large CODABAR Ratio Check Digit UPC-A UPC-E EAN-8 EAN-8 EAN-8 EAN-13 EAN-13 EAN-13 Español List of menu :Print setting Menú4...
Page 138 List of menu :File English Menu Menu1 Print history Recall Delete Store Delete Español List of menu :Condition Menú Menú1 Recuperar Historial impr English Borrar Guardar Menu Menu1 Borrar inch:cm inch Alkaline Français Battery type Nickel-hydride Frame & Table Setting Length Menu Menu1...
Page 139 List of menu :Symbol English Menu Symbol Arrows Parenthesis Units Math Abbreviation Mark Number Double Figures ’+Double Figures LatinAmerica Europe Greek Cyrillic Español List of menu :Pictograph Menú Símbolo Flechas Parentesis Unidades Matemáticas English Abreviatura Marca Número Dobles Cifras ’+DoblesCifras Europa Menu Latinoamérica...
Page 141: Ec Declaration Of Conformity
Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC and Eco-design Directive 2009/125/EC and EU RoHS Directive 2011/65/EU. Product Label Printer Model LABELShop GREEN MACHINE Manufacturer K-SUN Corporation 370 SMC Drive PO Box 309 Somerset WI 54025, USA The above product has been evaluated by the following European standard.
Page 142 Printed on Recycled Paper GMManual 01_2014...

K-sun green machine User Manual

Introduction

Introduction

Appendix

Getting Started AC Adapter

Getting Started

Basic Operations 1

Basic Operations 2

Telecom/Electrical Label Mode

Additional Functions

Quick Links

Need help?

Questions and answers

Related Manuals for K-sun green machine

Summary of Contents for K-sun green machine

Table of Contents