Related Manuals for Miele LaPerla G 2830 SCi
Summary of Contents for Miele LaPerla G 2830 SCi
-
Page 1: Operating Instructions
Operating instructions LaPerla G 2830 SCi To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 06 696 130... -
Page 2: Table Of Contents
Loading the dishwasher ........ - Page 3 Problems water intake/drain ......... 54 General problems with the dishwasher ....... . . 56 Sounds .
-
Page 4: Important Safety Instructions
WARNING – When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance. - Page 5 Do not install or use a damaged dishwasher. A damaged appliance is dangerous. Unplug the machine and call your Miele dealer or the Miele Technical Service Department. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
- Page 6 It will destroy the rinse aid compartment and water softener. If the power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. Disposal of an appliance...
-
Page 7: Guide To The Dishwasher
Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm Guide to the dishwasher g Filter combination h Data plate i Child Safety Lock in the door handle (not visible) j Rinse aid reservoir... -
Page 8: Control Panel
K (Information) touch control To display more info about the displayed menu b s (On/Off) touch control To turn the dishwasher on and off c Selection touch controls To select a menu point displayed next to the touch control. -
Page 9: Display
To confirm these messages or settings touch and the next menu or another menu level will appear. The "Settings J" menu allows you to adjust the dishwasher to your individual needs. See "Settings" for more information. -
Page 10: Caring For The Environment
^ For fastest possible wash times, yet higher energy consumption, connect the dishwasher to a hot water source. ^ If the dishwasher is connected to hot water, select "Energy Saver" when washing light to normally soiled dishware. The water will not be... -
Page 11: Before Using For The First Time
To open the door ^ Press the release catch inside the door grip. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. - Page 12 Before using for the first time Welcome screen ^ Turn the dishwasher on with the sensor s. The Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting.
- Page 13 After confirming this message, the two messages salt Insufficient rinse aid and the display changes to the main menu. Main menu ° Normal ° Pots + Pans ° China + Crystal The dishwasher can now be used or turned off. Insufficient may show. Confirm with 12:00...
-
Page 14: Water Softener
Before using for the first time Water softener Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. To achieve good cleaning results, the dishwasher needs soft water. -
Page 15: Filling The Salt Container
Filling the salt container Inadvertently filling the salt container with dishwashing detergent will damage the water softener. Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. When opening the salt container, water will run out. -
Page 16: Salt Refill Message
^ Clean any excess salt from the threads of the container opening. Close the lid firmly. ^ If the dishwasher will not be used immediately, run the "Short" program. This will remove any traces of salt from inside the wash cabinet. -
Page 17: Rinse Aid
Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. -
Page 18: Rinse Aid Refill Message
Before using for the first time ^ Pour liquid rinse aid into the reservoir until it its visible on the surface of the screen. The rinse aid reservoir holds approx. 3.7 oz (110 ml). ^ Press on the flap until you hear it click shut. -
Page 19: Loading The Dishwasher
Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes. Plastic items may discolor permanently if they come in contact with food dyes. -
Page 20: Items Not Recommended For Dishwashing
– When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe. Only wash items marked "dishwasher safe" in the dishwasher. – If fine glassware is washed in the dishwasher select the "China &... -
Page 21: Split Cutlery Tray
The inserts of the cutlery tray can be removed. Single inserts can be removed to make room for tall items in the upper basket. Loading the dishwasher Spoons with thick handles may have to be placed as knives and forks with their heads in the holders... -
Page 22: Upper Basket
Loading the dishwasher Upper basket For safety reasons only use the dishwasher with the upper and lower basket inserted. Exception: The programs "Large items normal" and "Large items soiled" are designed for use without the upper basket. ^ Load the upper basket with small,... - Page 23 The height of the cup rack can be adjusted in two levels. ^ Pull the cup rack upwards and let it engage at the desired height. Loading the dishwasher Coffee bar (depending on model) Glasses can be leaned against the coffee bar for a secure stand.
- Page 24 Loading the dishwasher Glassware rail (depending on model) The glassware rail is designed for a secure stand of tall glasses and stemmed glassware. ^ Flip the bar down to lean tall glasses on it. ^ If necessary take out part of the cutlery tray to make room for tall glasses.
- Page 25 ^ Insert the nipples under the hooks a. ^ Open the flaps b and insert the bottle neck into the opening. ^ Small items like the rings and caps of the bottles can be inserted in the open spaces. Loading the dishwasher...
-
Page 26: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket The upper basket can be raised or lowered to accommodate tall items. The basket can also be angled to fit tall items in both, the upper and lower baskets. The angles should not be set to opposite extremes. -
Page 27: Lower Basket
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Loading the dishwasher... - Page 28 Loading the dishwasher Comfort inserts The comfort inserts are designed for cups, glasses, plates, bowls, pots, etc. ^ To insert tall items, raise the cup rest. ^ Lean or hang stemmed glassware such as wine or champagne glasses in the cut outs of the cup rest.
-
Page 29: Basket Accessories
If placed anywhere else, water will not reach all surfaces. The bottle will not be properly cleaned. Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. -
Page 30: Use
Detergent Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Fill the detergent dispenser only when you are ready to start the dishwasher. Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. -
Page 31: Adding Detergent
Adding detergent ^ To open, press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. -
Page 32: Turning On
^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if closed. ^ Turn the dishwasher on by touching the s control. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. -
Page 33: Program Guide
Program Normal For normally soiled dishware with dried on food Pots + For normally soiled pots and pans with dried Pans on food, and heavily soiled dishware, 120% detergent recommended China + For temperature sensitive glassware and lightly Crystal soiled dishware, 50% detergent recommended; sensor controlled GlassCare program Short "Quick program"... - Page 34 For dishware with dried on cheese; 120% detergent recommended Sani Wash To sanitize dishware, e.g. baby bottles, cutting boards and preparation dishware Plastics To gently clean dishwasher safe plastics and plastic toys Large items For extra large, heat-resistant items soiled e.g. large vases...
-
Page 35: Use
Selecting Options Options can be added to the selected program. ^ Select The display shows the available options for the selected program. Available options: Pre-rinse: – For easily removable soiling Soak: – To soak stubborn soiling. When using powder detergent, fill approx. 1 teaspoon (5 g) of detergent in the detergent compartment I. -
Page 36: Starting A Program
You can now select the detergent used. Availabe selections are: Powder, Gel, "2 in 1" and "3 in 1" tabs. See "Settings J, Detergent". Starting a program ^ Select Start The program begins. Cancel a program only in the first 5 minutes. -
Page 37: At The End Of A Program
The dishwasher continues to use electricity until turned off with the s control. ^ If the dishwasher is not used for a longer period of time, e.g. vacationing, turn off the water supply. Interrupting a program A program is interrupted as soon as the door is opened. -
Page 38: Changing A Program
Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Select ^ Confirm the message The program is canceled. ^ Select The display changes to the main menu. ^ Select and start the desired program. -
Page 39: Additional Options
"Delay Start", the detergent could leak. dishwasher door to prevent children from coming in contact with the detergent. ^ Turn the dishwasher on by touching the s control. ^ Select the desired program. ^ Select The most recent saved start time will be displayed. - Page 40 Additional options The program name and the start time are displayed. The program starts automatically at the selected time. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed. Proceed as follows: ^ Select ^ Select The display changes to the main menu.
-
Page 41: Settings J
The "Settings J" menu allows you to adjust standard settings Open the Settings J menu ^ Turn the dishwasher on by touching the s control. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. -
Page 42: Time Of Day
Settings J Language J The display contents can be shown in different languages. The displayed language can be changed by the submenu "Language J". ^ Select the desired language and confirm with The flag behind the word "Language J" serves as a guide when an unfamiliar language is selected. - Page 43 Detergent To achieve the best results the used detergent can be set on your dishwasher. The selection allows "Powder", "Gel", "2 in 1" and "3 in 1" tabs. The program cycle sequence will be adjusted for the selected detergent. Depending on the program the program running time may increase.
-
Page 44: Adjust Sensor Wash
Settings J Water hardness The dishwasher is equipped with a sensor softener, which automatically detects the hardness of your tap water. After plumbing the dishwasher and finishing a program, e.g. "Rinse & Hold", the water hardness is displayed in the menu "Water hardness". - Page 45 Reorganize program list The order of the programs in the program list can be reorganized. Frequently used programs can be saved to the first three positions. ° Normal B ° Pots + Pans ° Cancel ^ Select the program to be saved to the first program list position.
-
Page 46: Save Options
Settings J Save options Additional options can be selected for some programs, e.g. extended drying. See "Use - Selecting options". Save options allows you to save the selected options for future use with this program. The function is turned off by default. ^ Select the desired setting and confirm with... -
Page 47: Child Safety Lock
Child Safety Lock The Child Safety Lock protects the dishwasher from misuse. If the dishwasher is turned on while the Child Safety Lock is activated, the display shows The lock must be deactivated before the dishwasher can be used. As long as the Child Safety Lock is activated, the dishwasher is locked every time it is turned on. -
Page 48: Program Lock
Settings J Program lock The running program can be locked. This function prevents accidentally changing a program during use. You can select if the program lock should be activated or not. The actual locking of the program is done when a program is started. - Page 49 To cancel a running program, the program lock must be deactivated first. Once the program is finished, deactivate the lock or turn the dishwasher off and on again before starting a new program or selecting settings. Deactivating the program lock °...
- Page 50 The buzzer at the end of a program sounds five times in intervals with a brief break. The buzzer sounds up to one hour if the dishwasher in not turned off. Buzzer in case of a fault The buzzer for a fault sounds continuously.
-
Page 51: Keypad Tone
Memory The memory function saves the last selected program. If you turn the dishwasher off and on again or open and close the door after a program has finished, the display shows not the main menu but the last selected program. -
Page 52: Factory Default
The dishwasher has three demo programs for showrooms. The programs "Demo mode" and "Endless demo mode" show the use and function range of the dishwasher. Demo mode – The program is started by touching a control. It runs once and must be started again. -
Page 53: Frequently Asked Questions
– Turn the dishwasher off by touching the s control. After a few seconds: – Turn the dishwasher – Select the desired program. Start – Select If the problem persists, call Technical Service. – Turn off the water supply. – Call Miele Technical Service. -
Page 54: Problems Water Intake/Drain
Solution Open the water supply all the way. Before fixing the fault: – Turn the dishwasher off by touching the s control. – Open the water supply all the way and restart the program. – Clean the water intake filter, see "User Maintenance... - Page 55 – If the fault is displayed again, use a different program. Before fixing the fault: – Turn the dishwasher off s. – Clean the triple filter. – Clean the drain pump and the non-return valve. – Clean the drain pump and the non-return valve.
-
Page 56: General Problems With The Dishwasher
– Restart the program. Open the dishwasher door and rearrange the items blocking the spray arms. – Turn the dishwasher off by touching the s control. Then: – Clean the spray arms. See "User Maintenance Instructions". - Page 57 Remove the residue. The moisture will evaporate after a short time. Before fixing the fault: – Turn the dishwasher off by touching the s control. Clean the triple filter. See "User Maintenance Instructions". Clean the drain pump and the non-return valve, see maintenance instructions.
-
Page 58: Sounds
This may be caused by the installation or the diameter of the pipe. Solution Interrupt the program, rearrange the items blocking the spray arm. Interrupt the program and rearrange loose items. This has no effect on the dishwasher. If in doubt contact a plumber. -
Page 59: Poor Cleaning Results
Frequently asked questions Solution See "Loading the dishwasher". Select a more intensive program, see "Program Guide". Use the function "Adjust Sensor Wash". See "Settings J - Adjust Sensor Wash". - Page 60 Select the detergent setting to the detergent used. See "Settings J - Detergent". Increase the dosage. See "Settings J - Rinse aid". for the first time". Use a different detergent. Try normal tabs or powder detergent. Call Miele Technical Service.
- Page 61 Salt residuals got in the wash cycle. Solution Use a different detergent. There is no remedy. Only wash dishwasher safe glasses in the dishwasher. Select a program with a higher temperature. Use a different detergent. Use more detergent, see "Adding detergent".
-
Page 62: After Sales Service
Miele’s Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. -
Page 63: Transport
To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. -
Page 65: User Maintenance Instructions
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use. -
Page 66: Cleaning And Care
The wash cabinet can be cleaned with a dishwasher cleaner such as "Dis Cleaner" available from your Miele dealer, Miele or online at www.store.miele.com. Door and the door seal ^ Wipe the door seals regularly with a damp cloth to remove food deposits. -
Page 67: Triple Filter System
^ Confirm with The display changes to the program menu. Cleaning and Care Cleaning the triple filter ^ Turn off the dishwasher before cleaning. ^ Turn the handle counterclockwise to after release the triple filter system, a. ^ Remove the triple filter from the machine. - Page 68 Cleaning and Care To clean the underside of the filter the flap must be opened. ^ Push the clips together a and open the flap b. ^ Rinse under running water. ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet.
-
Page 69: Cleaning The Spray Arms
Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). -
Page 70: Cleaning The Water Inlet Filter
If your water contains a large number of insoluble substances, a filter between the water valve and the intake hose connection is recommended. These filters can be purchased from Miele. Cleaning the filter ^ Turn off the dishwasher and pull the plug. -
Page 71: Cleaning The Drain Pump And Non-Return Valve
If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). -
Page 73: Installation Instructions
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions. -
Page 74: Help To Protect The Environment
Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. -
Page 75: Electrical Connection
Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED. -
Page 76: Plumbing
Plumbing Connection to the water supply Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot or cold water source. For lowest energy consumption connect the dishwasher to a cold water source. -
Page 77: Drainage
5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39"... - Page 80 Alterations reserved/5205 M.-Nr. 06 696 130 / 00 G 2830 SCi / en - US...
Need help?
Do you have a question about the LaPerla G 2830 SCi and is the answer not in the manual?
Questions and answers