Related Manuals for Miele 05 620 661
Summary of Contents for Miele 05 620 661
-
Page 1: Installation Instructions
Installation instructions Integrated dishwasher To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 620 661... - Page 2 3. Install the slide skis ..........13 4. Install the dishwasher under the countertop ......14 5.
- Page 3 Installation, maintenance and re- pair work should be by a Miele authorized service technician. Work by unqualified persons could be a hazard and may void the warranty. This equipment is not designed for maritime use or for use in mobile installations such as caravans or air- craft.
- Page 4 Before installation, make sure the voltage and frequency listed on the data plate correspond with the house- hold electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. To guarantee the electrical safety of this appliance, continuity must exist between the appliance and an effective grounding system.
- Page 5 Toutefois, il peut être parfois possible de faire l’installa- tion de ces applications sous certaines conditions. Veuillez contacter le Con- cessionnaire Miele le plus près de chez-vous ou le Département du servi- ce technique Miele pour leur donner vos exigences précises.
- Page 6 Avant l’installation, s’assurer que la tension et la fréquence énumérées sur la plaque signalétique correspon- dent à la source d’électricité de la rési- dence. Ces données doivent corres- pondre afin d’éviter de vous blesser et d’endommager l’appareil. Consulter un électricien qualifié si vous avez des doutes.
- Page 7 The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Old appliances may contain materials that can be recycled.
- Page 8 ^ Gently pull on the upper portion of the mounting bracket until the door latch releases (small arrow). ^ Grip the T shaped opening with a fin- ger and pull the door open.
- Page 9 (845-864 mm) are not possible using the supplied legs. For this height range, or for heights greater than 34 " (886 mm), ex- tended legs (part # 02 702 601) are necessary. Contact the Miele Technical Service Department for the appropriate legs. " - 34"...
- Page 10 (889-940 mm) cannot be obtained using the supplied legs. For this height range, or for heights greater than 35" (889 mm), extended legs (part# 02 702 601) are neces- sary. Contact the Miele Technical Service Department for the appropriate legs.
- Page 11 Corian®, granite, marble or other solid, waterproof material, the steam deflector is not required. The steam deflector has an indicator re- flector to show when the dishwasher is running. The left side of the reflector and the optic indicator in the the control panel must line up for the reflector to work.
- Page 12 The steam deflector is not required for countertops made of solid, waterproof material. But it is needed for determin- ing the correct position of the optic indicator reflector. ^ Remove the black plastic reflector holder from the steam deflector. ^ With the reflector cut out left and frontward, align the steam deflector with the front edge of the counter.
- Page 13 ^ First, adjust the height of the legs so that the top of the dishwasher is roughly " (3 mm) below the countertop.
- Page 14 ^ Make a 2" x 4" (5 x 10 cm) cut out in the side or bottom of the cabinet ad- joining the dishwasher. This cut out is necessary for connections to pass through.
-
Page 15: Level Legs
^ Tipping the machine slightly back- wards, if posssible will make adjust- ing the front legs easier. Make sure the machine is level when adjust- ments are complete. The dishwasher should be raised until it just touches the underside of the countertop. - Page 16 A custom door panel must be installed on the dishwasher before it can be safely operated. A single large panel or a two piece panel separated at the drawer line can be used. Panel size is determined in the follow-...
- Page 17 The door panel is attached to the dish- washer using the mounting bracket that comes secured to the front of the unit. To remove the bracket: ^ Open the door 2 - 4" (5 - 10 cm). ^ Loosen the bracket retaining screw (black arrow) located on each side of the machine door.
- Page 18 ^ Make sure the dishwasher is level. ^ Measure the distance round hole in the machine outer door panel (shown in inset) and the lower edge of the adjoining cabinet door. ^ Place the door panel on a flat sur- face, good side face down, being careful not to scratch the surface.
- Page 19 ^ Double check the location of the bracket before mounting the panel to the dishwasher. The door handle must be installed on the panel before it is attached to the machine. It should be located in the center of the panel at a height that will match the surrounding drawer handles.
- Page 20 ^ Open the door 2 - 4" (5 - 10 cm). ^ Place the lower mounting clips into the slots of the dishwasher door as shown in the illustration. ^ Seat the U shaped slots of the upper bracket onto their respective locator pins.
- Page 21 ^ The panel can be raised or lowered by turning the lower screw on each side of the dishwasher door. To raise the panel turn clockwise. To lower the panel turn counterclock- wise.
- Page 22 Do not drill any additional holes through the wash cabinet. If in doubt on how to secure the dishwasher, please call Miele’s Technical Service Department.
- Page 23 For openings exactly 23 wide: ^ Open the dishwasher door and re- move the caps covering the mount- ing holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adja- cent cabinets using the supplied screws and bushings.
- Page 24 – turn counterclockwise to de- crease the tension. If the door springs can not be adjusted enough (the door falls), the custom door panel is too heavy. Call your Miele dealer or the Technical Service Department for advice on stronger door springs.
- Page 25 An air gap is built into the water inlet system to prevent potable water from mixing with waste water. The dishwasher can heat its own water to the temperatures required by the wash program. This allows the option of connecting the machine to either a hot or cold water source.
- Page 26 If the standard " copper plumbing for a dishwasher already exists with a com- pression fitting and valve as pictured: ^ Cut the " copper tubing after the valve. ^ Install the " compression to MHT (Male Hose Thread) adapter (supplied with the machine), as illus- trated.
- Page 27 – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of (22 mm). Drain hose extensions can be ordered from Miele’s Technical Service Department. – A built-in swivel connector allowing the drain hose to be routed in any direction.
- Page 28 ^ Cut off the vent cap located at the right rear of the triple filter system, as illustrated. Since all Miele dishwashers are equipped with an odor trap and non- return valve, the drain hose can be connected directly to the drain pipe as illustrated.
- Page 29 The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle.
- Page 30 The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An o- pening through the partition between the compartments of 1 can be made to allow the plug to pass through.
- Page 31 Once the dishwasher is level and secured it should be tested. ^ Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dish- washer. If not removed, the key could become lodged in the circula- tion pump.
- Page 32 Before installing the toekick, measure- ments must be taken to ensure that the toekick will not interfere with the com- plete opening of the dishwasher door. The door panel overhang ( ), and toekick depth of recess ( ), determine the maximum dishwasher toekick height ( ).
- Page 33 ^ Insert the mounting bracket with the flange pointing toward the center of the machine. ^ Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration). ^ Insert the mounting bracket with the flange pointing toward the outside of the machine.
- Page 34 The included toekick will fit without modification if the machine is set to its maximum height and the toekick is re- cessed as far as possible (4" / 10 cm). If the machine height is less than maxi- mum, or if the toekick is not recessed 4" (10 cm), the toekick must be shortened.
- Page 35 ^ Carefully open the dishwasher door until it hits the toekick. ^ Using the front lower edge of the door panel as a guide, draw a line across the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close to...
- Page 36 Alteration rights reserved (MVi60) / 2702 M.-Nr. 05 620 661 / V This bio-friendly paper was bleached without the use of chlorine.