Page 3
The installation and service should be done by a qualified service technician. 1. When installing the GA-1330 to the Equipment, be sure to follow the instructions described in the "Unpacking/Set-Up Procedure for the GA-1330" booklet which comes with each unit of the GA- 1330.
E-mail alert status Yes (Cancels by the soft key) Disk 4: Driver CD-ROM Power supply Supplies via copier Internet Explorer 6.0 (AC power supply built-in) AC120mA *1: Mac OS 10.5 is supported by running change. GA-1330 CONFIGURATION 1 - 1...
Invoice on Letter, A5 on A4, Letter on Letter, A4 on A4 Binding Edge Margin Shift N-up Win9x: 2/4 2/4/6/8/16 Win2k/XP/Vista: 2/4/6/8/16 N-up order Z, Reverse Z, N, Reverse N N-up Border (Single hairline/ On/Off Single thin line/ On/Off Double hairline/ Double thin line) GA-1330 SPECIFICATIONS 1 - 2...
Page 7
On/Off Print Auditor Job Retention Watermark On/Off On/Off (With functional restriction) Page Protection Job Compression None, Fastest, Fast, Medium, Best Job Compression None, Very High, High, Medium, Draft *1: Mac OS 10.1 is not supported. GA-1330 SPECIFICATIONS 1 - 3...
Page 8
Light Red/Green/Blue Green Light source source can be selected only when the color mode is in "Monochrome". Void On/Off When On is selected, the edges of images are cut. GA-1330 SPECIFICATIONS 1 - 4...
The b Button Manager settings are disabled. • When the network expansion kit is connected, the scanner func- tion through TWAIN (pull scan) and push scan which used button manager on pc are not available. GA-1330 SPECIFICATIONS 1 - 5...
2) Connect the connector of the network expansion kit to the con- nector of the main unit. 3) Secure the rear cabinet cover to the main unit with the screw. 4) Attach the RADF to the main unit. GA-1330 UNPACKING AND INSTALLATION 3 - 1...
Page 11
3) Connect the network cable. Insert the power plug of the copier to the outlet, turn the main switch of the copier to the “ON” position, and perform network setting and installation of the software. GA-1330 UNPACKING AND INSTALLATION 3 - 2...
1. (In this case, all the changes in values made before pressing the clear key are cleared.) GA-1330 SETUP IN A WINDOWS ENVIRONMENT 4 - 1...
Page 13
Box version you want to update, from the file selection menu Click the button on the screen, the message shown in Fig. 2 indicated in Fig.4. appears. [Fig. 4: Specifying the file] [Fig.2: Switch to firmware upload mode] GA-1330 UPDATING NETWORK BOX FIRMWARE 5 - 1...
Page 14
Network Box from the DHCP server and display the updat- ing mode URL again using the browser. When a proxy server is used, the screen may not be updated by reloading. In that case, you need to update manually. GA-1330 UPDATING NETWORK BOX FIRMWARE 5 - 2...
Page 15
The quantity of the result for which LDAP searched exceeded the maximum quantity which can be searched. There are too many addresses which were in agreement with reference conditions. Please increase the number of reference characters and perform re-reference. GA-1330 TROUBLE CODE 6 - 1...
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: <Solder composition code of lead-free solder> Solder composition Solder composition code Solder composition...
Page 35
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.