Related Manuals for Toyotomi GAN-A180VL
Summary of Contents for Toyotomi GAN-A180VL
- Page 5 Installing, starting up, and servicing air conditioner can be Make sure the outdoor unit is installed on a stable, level surface with no accumulation of snow, leaves, or trash hazardous due to system pressure, electrical components, and equipment location, etc. beside.
- Page 8 11 0 10 0 Conditions Conditions Indoor:DB27°C WB19°C Indoor:DB20°C Indoor air flo w Supper High Indoor air flo w Supper High Pipe lengt h 5m Pipe lengt h 5m 32 33 34 35 36 37 38 39 40 41 42 43 44 45 Outdoor temp.(°C) Outdoor temp.(°C)
- Page 10 GAN-A128VL Φ55 Φ55 GAN-A135VL Φ55 Φ55 GAN-A180VL Φ55 Φ55 GAN-A240VL Φ70 Φ70...
- Page 13 GAS SIDE 3-WAY VALVE 4-Way valve Muffler Di s charge HEAT EXCHANGE (EVAPORATOR) Suction Accumlator COMPRESSOR HEAT EXCHANGE (CONDENSER) LIQUID SIDE Strainer Strainer 2-WAY VALVE Capillary COOLING HEATING...
- Page 15 RECEIVER AND POWER DISPLAY BOARD TUBE TEMP. ROOM TEMP. YEGN DISPLAY SENSOR SENSOR EARTH-PLATE YEGN YEGN L101 ROOM TUBE DISP1 EVAPORATOR DISP2 AP1 PRINTED CIRCUIT BOARD N(1) L(4) COMP(3) JUMP SWING OFAN HEALTH-N HEALTH-L IONIZER STEPPING MOTOR FAN MOTOR BN(BK) RECEIVER AND BU(WH) POWER...
-
Page 16: Fan Motor
COMP. C(T,U) COMP YEGN S(W,X) R(M,V) FAN MOTOR YEGN YEGN CAP. RD BN N(1) BK(BU) (BN) 4-WAY VALVE CAP. TERMINAL BOARD (OG) C(T,U) COMP. FAN MOTOR COMP 6YEGN YEGN S(W,X) R(M,V) (BU) YEGN N(1) RELAY BK（RD） 10BU 11OG... - Page 17 3 4 5...
-
Page 18: Timer Off
ON/OFF Press it to start or stop operation. Press it to decrease temperaturesetting. Press it to increase temperaturesetting. MODE Press it to select operation mode(AUTO/COOL/DRY/FAN/HEAT). Press it to set fan speed. SWING Press it to set swing angle. I FEEL Press it to set HEALTH or AIR function. -
Page 19: Remote Controller Description
LOCK icon: is displayed by pressing "+" and “-” buttons simultaneously. Press them again to clear the display. SET TIME display: After pressing TIMER button,ON or OFF will blink.This area will show the set time. DIGITAL display: This area will show the set temperature. In SAVE mode,"SE" will be displayed. AIR icon: is displayed when pressing the AIR button.Press this button again to clear the display. - Page 20 SWING: Press this button to set up & down swing angle, which circularly changes as below: This remote controller is universal. If any command is sent out,the unit will carry out the command as indicates the guide louver swings as: I FEEL: Press this button to turn on I FEEL function.
-
Page 21: Replacement Of Batteries
Press “TEMP” and “CLOCK” simultaneously in HEAT mode to start 8℃ Heating Function Nixie tube on the remote controller displays “ ” and a selected temperature of “ 8℃”. (46 if Fahrenheit is adopted). Repeat the operation to quit the function. About Back-lighting Function The unit lights for 4s when energizing for the first time, and 3s for later press. - Page 22 Tamb. Start cooling Tpreset +1 ˚C Original operating status Tpreset –1 ˚C Stop cooling ≥ 6 min. ≥ 3 min. ≥ 6 min. Compressor Outdoor fan Setting fan speed Indoor fan Stop During antifreeze protection Compressor Outdoor fan Indoor fan Preset speed Stop...
- Page 23 amb. Cooling preset Dehumidfying preset― Stop min. min. min. Compressor Outdoor fan Indoor fan Low speed Stop Stop heating preset Original operating status preset Start heating min. Compressor Outdoor fan preset wind min. preset wind Indoor fan min. Reversing valve Stop...
- Page 25 0 (0º)
- Page 28 Space to the ceiling 15cm Above Space to the wall 15cm Above 15cm Above Space to the wall 300cm Above Above Air outlet side Space to the floor The dimensions of the space necessary for proper ● installation of the unit include the minimum permissible distances to adjacent parts.
- Page 29 Flooded Wiring Cover GAN-A128VL GAN-A180VL GAN-A240VL GAN-A135VL N(1) N(1) yellow- yellow- orange yellow- orange blue black violet blue black...
- Page 30 External connection Gas side piping electric wire Liquid side piping Tailing 2 Gas side piping Tailing 1 Liquid side insulation Piping insulation Finally wrap it Fig.3 Water drainage pipe with tape Left Right Left rear Fig.4 Right rear Fixing hook Mounting plate Mounting...
- Page 31 Manifold Valve Multimeter Manometer -76cmHg Hi handle Lo Handle Charging hose Low pressure valve Fig.6 Vacuum pump Drain-water hole Drain-water hole Bottom frame Bottom frame Drain plug Drain connecter Drain connecter Hose (available commercially, Hose (available commercially, inner dia. 16mm) inner dia.
- Page 32 Fig. a Fig. b Air filter Healthy filter Fig. c...
- Page 42 (1) Malfunction of temperature sensor Start Is the wiring terminal between temperature sensor and the controller loosened or poor ly contacted? Insert the temperature sensor tightly Malfunction is eliminated. Is there short circuit due to tri-pover of the par ts? Make the parts upright Malfunction is eliminated.
- Page 43 (2) PG motor (indoor fan) does not operate (H6) “H6”is displayed on the unit. Stir the fan blade with a hand when the unit is DE - ENERGIZED . Reinstall the motor Does the and the blade to blade rotate make it rotate unsmoothly? smoothly.
- Page 44 (3) Jumper cap malfunction (C5) C5 is displayed on the unit. Install a matching Is there jumper cap on the jumper cap . controller? Is the malfunction eliminated? Re-insert the jumper Is the jumper cap inserted incorrectly or improperly? Is the malfunction eliminated? Replace the jumper...
- Page 45 Start Normal fluctuation is within 10% of the rated voltage on the Is the supply voltage unstable with big fluctuation? Malfunction is eliminated. nameplate Is the supply voltage too low with overload? Adjust the supply voltage to maintain it within normal range Malfunction is eliminated.
Need help?
Do you have a question about the GAN-A180VL and is the answer not in the manual?
Questions and answers