Advertisement

READ BEFORE USE! Model No.:
HYPH4601-4
Item No.: 67775

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HYPH4601-4 and is the answer not in the manual?

Questions and answers

Jeff
March 12, 2025

Where can I get replacement glass tube for bond patio heater 8” x 28.75”

1 comments:
Mr. Anderson
March 12, 2025

You can request a replacement glass tube for the BOND MANUFACTURING patio heater model HYPH4601-4 by calling BOND toll-free at 1-866-771-2663 or emailing customer.service@bondmfg.com.

This answer is automatically generated

Summary of Contents for BOND MANUFACTURING HYPH4601-4

  • Page 1 READ BEFORE USE! Model No.: HYPH4601-4 Item No.: 67775...
  • Page 2 General Safety Information This manual contains important information about Failure to comply with the precations and instructions the assembly, operation and maintenance of this provided with this heater can result in death, serious heater. bodily injury and property loss or damage from General safety information is presented in these hazards of fire, explosion, burn, asphyxiation, and/or first few pages and is also located throughout the...
  • Page 3 Never store propane near high heat, open flames, pilot lights, direct sunlight, other ig- nition sources or where temperatures ex- BURN HAZARD ceed 120 Never leave heater unattended when hot or Propane is heavier than air and can accumu- in use. late in low places.
  • Page 4 24 in /60.9 cm and sides 24 in /60.9 cm. 24 in/60.9cm 24 in /60.9cm...
  • Page 5 Tank Housing Burner Glass Tube Glass Tube Ring Mesh Guard Upper Supporter Upper Combination Tank Housing Supporter Wheel Handle Attached into the M5x12 screw upper supporter Attached into M4x10 screw the burner cover M5x12 screw in hardware packing...
  • Page 6 M5 lock nut in hardware packing 1 in hardware packing, 2 M8x16 screw screwed into wheel M8 lock nut screwed into wheel M6 nuts assembled into handle M6 washer assembled into handle M6x12 screw in hardware packing M6 lock nut in hardware packing Anchoring Arm in hardware packing...
  • Page 7 Step 1:Unscrew the handle nuts (Q)and washer(R) and assemble the handle into tank housing(A). Step 2: Unscrew the wheel screws (O) and nuts (P) and assemble the wheel (I) into tank housing base. Step 3:Use the M8x16 screw (O) and M5x12 screw(M) from the hardware packing to attach the tank housing supporter(H) into the base hole and the tank housing and don’t fasten them.
  • Page 8 Step 9:Put the upper combination(G) into the supporter and glass tube to make sure the three holes match up and use screws (from Step 7) to fasten them. Step 5:Use 1pc M5x12 s c rew (M) to fasten the tank housing supporter.
  • Page 9 C onnect H ose & Regulator to C ylinder Step 1 - Gas Cylinder Required ■ You must provide propane gas and propane cylinder. Figure 1 Use a standard 20lb propane cylinder only. ■ Use this heater only with a propane vapor withdrawal 20LB Propane Cylinder supply system.
  • Page 12 This appliance shall be used only in a well- ventilated space and shall not be used in a building, garage or any other enclosed area. This appliance may be installed with shelter no more inclusive than: 1. With walls on all sides, but with no overhead cover.
  • Page 13 PLEASE CALL BOND TOLL FREE # 1-866-771-BOND(2663) OR TO BETTER EXPEDITE YOUR REQUEST FEEL FREE TO EMAIL US customer.service@bondmfg.com OR VISIT OUR WEBSITE UNDER CUSTOMER SERVICE SUPPORT www.bondmfg.com BOND MANUFACTURING CO. 1700 West 4th Street, Antioch, CA 94509 USA MADE IN CHINA...

Table of Contents

Save PDF