HAKO 850B Instruction Manual

Smd rework station

Hide thumbs

Thank you for purchasing the Hakko 850B SMD Rework

Station.

The Hakko 850B is designed to solder and desolder surface

mounted devices with hot air.

Please read this manual before operating the Hakko 850B.

Keep this manual readily accessible for reference.

PACKING LIST / SPECIFICATIONS ....................................................... 1

SAFETY INSTRUCTIONS ...................................................................... 2

PART NAMES ......................................................................................... 3

PREPARATION: ASSEMBLY AND ELECTRICAL CONNECTION ......... 4

OPERATION ........................................................................................... 5

MAINTENANCE / INSPECTION ............................................................ 7

TEMPERATURE DISTRIBUTION CHART ............................................. 8

OPTIONAL NOZZLES .......................................................................... 11

PARTS LIST / HANDPIECE ................................................................. 12

WIRING DIAGRAM .............................................................................. 15

SMD Rework Station

STATION ....................................................................... 13

Table of Contents

Need help?

Do you have a question about the 850B and is the answer not in the manual?

Questions and answers

Summary of Contents for HAKO 850B

Page 1: Table Of Contents
SMD Rework Station Thank you for purchasing the Hakko 850B SMD Rework Station. The Hakko 850B is designed to solder and desolder surface mounted devices with hot air. Please read this manual before operating the Hakko 850B. Keep this manual readily accessible for reference.
Page 2: Packing List / Specifications
PACKING LIST Check the contents of the Hakko 850B package and confirm that all the items listed below are included: * This product does not include a nozzle. A large Hakko 850B station ..........1 selection of nozzles is available for the Hakko Power cord ............
Page 3: Safety Instructions
G Advise those in the work area that the unit can reach very high temperatures and should be considered potentially dangerous. G Turn the power OFF when no longer using the Hakko 850B or when leaving it unattended. G Before replacing parts or storing the unit, allow the unit to cool and then turn the power OFF.
Page 4: Part Names
PART NAMES Station Handpiece holder Handpiece holder POWER mounting screw mounting screw Air flow lamp Power switch HEAT CONTROL AIR CONTROL Heater lamp Air flow control knob Temperature control knob Power receptacle Handpiece holder Fuse Handpiece Nozzle (not included) Accessories FP pick-up with (S) wire (Width of wire 14mm (0.55in.)) FP pick-up wire (L)
Page 5: Preparation: Assembly And Electrical Connection
(Figure 2) (Figure 3) C. Electrical Connection and When installing an optional nozzle to the Hakko 850B, do Power ON not remove this inside screw. 1. Connect the power cord to the power receptacle on the back panel of the station.
Page 6: Operation
OPERATION G G G G G QFP Desoldering POWER 1. Adjust the air flow and temperature control knobs. HEAT CONTROL AIR CONTROL Refer to the temperature distribution chart (page 8) to adjust the air flow and temper- ature control knobs. Wait for the temper- Air flow control knob ature to stabilize for a short period of time.
Page 7 OPERATION QFP Soldering 1. Apply the solder paste. Apply the proper quality of solder paste and install the SMD on the PWB. 2. Preheat the SMD. Refer to the photo to preheat SMD. 3. Soldering Heat the lead frame evenly. 4.
Page 8: Maintenance / Inspection
MAINTENANCE / INSPECTION G G G G G Broken heating element A. Open the handpiece 1. Remove the three screws holding the handpiece together. (Figure 1) 2. Move the tube away from the handpiece, as shown. 3. Open the handpiece. Disconnect the grounding wire sleeve (1) and pipe from (Figure 1) the protruding portion of the handle.
Page 9: Temperature Distribution Chart
The temperature distribution chart relating air-flow and temperature settings for different nozzle types provided with the Hakko 850 are not to be used with the 850B. The 850B uses a different pump and control system and the flow-rates and temperature do not correspond.
Page 10 TEMPERATURE DISTRIBUTION CHART A1133 A1135B A1134 SOP 7.5×15 (0.3×0.59) PLCC 17.5×17.5 (0.68×0.68) SOP 7.5×18 (0.3×0.7) (44 Pins) Air Temperature Air Temperature Air Temperature Air flow 2 Air flow 2 Air flow ˚C ˚C ˚C (932˚F) (932˚F) (932˚F) (572˚F) (572˚F) (572˚F) (212˚F) (212˚F) (212˚F)
Page 11 A1257B A1258B A1259B SOP 11×21 (0.43×0.83) SOP 7.6×12.7 (0.3×0.5) SOP 13×28 (0.51×1.1) Air Temperature Air Temperature Air Temperature Air flow Air flow Air flow ˚C ˚C ˚C (932˚F) (932˚F) (932˚F) (572˚F) (572˚F) (572˚F) (212˚F) (212˚F) (212˚F) Temperature Control Knob Temperature Control Knob Temperature Control Knob A1260B A1261B...
Page 12: Optional Nozzles
OPTIONAL NOZZLES NOTE: PLCC (0.03) The size in Name/ Specification Air nozzle indicates the size of IC package. mm (inch) (0.07) A1124B Single Ø2.5 A1125B QFP 10×10 A1127B QFP 17.5×17.5 A1128B QFP 14×20 A1126B QFP 14×14 (0.09) (0.39×0.39) (0.55×0.55) (0.68×0.68) (0.55×0.78) A:10.2 (0.4) A:15.2 (0.6)
Page 13: Parts List / Handpiece
PARTS LIST / HANDPIECE NOTE: Spare or repair parts do not include mounting screws, if they are not listed on the description. Screws must be ordered separately. Self tapping screw Nominal size Self tapping screw 3×12 (3) Nominal size 2.6×10 (2) Item No.
Page 14: Station
PARTS LIST / STATION NOTE: Truss screw (Zn black) M4◊5 (12) Spare or repair parts do not include mounting screws, if they are not listed on the description. Screws must be ordered separately. Item Part Part Name Description B2539 Cover B2477 Handpiece holder assembly...

HAKO 850B Instruction Manual

Table of Contents

TABLE OF CONTENTS

Need help?

Questions and answers

Related Manuals for HAKO 850B

Summary of Contents for HAKO 850B

Table of Contents