Brother DCP-135C Quick Setup Manual

Unpack the machine and check the components
1
Start Here
Important
DO NOT
connect the
a.
USB cable yet.
Illustrations in this Quick Setup Guide
are based on the DCP-135C.
d.
e.
f.
Important
Do not push the
paper in too far.
Install the ink cartridges
5
a. c.
The LCD shows this message: Pull all the lock release levers
b.
Open the ink cartridge cover.
Check the print quality
6
a. b.
When the preparation process Check the quality of the four colour
❶
has finished, the LCD shows blocks on the sheet.
this message. (black/yellow/cyan/magenta)
■If all lines are clear and visible, press ▲
Press Colour start.
(Yes) to finish the quality check.
■If you can see missing short lines, press ▼
(No) and answer the LCD questions.
LS2346004
UK/IRE/SAF
Printed in China
c.
Make sure you have all components.
Note
・The components of your box may differ.
・Save all packing materials and the carton in case for any
reason you must ship your machine.
・A USB cable is not included.
You need to purchase a USB 2.0 cable that is no longer
than 2 metres.
Power Cord
b.
Remove the protective Remove the foam
tape and film. bag containing the ink
cartridges from on top
of the paper tray.
g.
Fan the stack of paper well. Close the output paper tray
cover and slowly push the
Gently put the paper into paper tray back into the
the paper tray. machine.
Check that the paper is flat
in the tray.
Make sure that the paper
side guides and paper
length guide touch the
edges of the paper.
❶ d.
down. Remove the yellow
❶
protective part .
❶
Set the LCD contrast (if needed)
7
a.
b.
❶
c.
OK d.
e.
Poor
Load plain A4 paper
2
a.
Pull out the paper tray.
Ink
Cartridges [x4]
Black (LC970BK)
Yellow (LC970Y)
Cyan (LC970C)
Magenta (LC970M)
CD-ROM
Quick Setup Guide
User's Guide
Connect the power cord
3
h. a.
Pull out the paper support Connect the power cord.
❶
until it clicks, and then unfold
❷
the paper support flap .
The machine must be fitted with an earthed/fused plug.
❷
❶
e.
Unpack the ink cartridge.
❶
Remove the protective yellow cap if it is still
attached. 1
❶
Important
Warning
❶
1
If ink gets in your eyes, wash them out with water
at once, and if irritation occurs consult a doctor.
Set the date and time
8
a.
Press Menu.
Press ▲ or ▼ to choose
0.Initial Setup, and then press OK.
b.
Press ▲ or ▼ to choose 0. Initial Setup, and then press OK.
2.LCD Contrast, and then press OK.
c.
Press ▲ or ▼ to choose Dark or Light.
1. Date&Time, and then press OK.
Press OK and then Stop/Exit.
b. ❶
Lift the output paper tray cover .
❶
1 1
Set the language
4
Warning
Important
DO NOT connect the USB
cable yet.
Note
The control panel warning
LED will stay on until you have
installed the ink cartridges.
f.
Install each ink cartridge in the direction of the arrow on the label.
❶
Take care to match the colour of the lock release lever with the
❷
cartridge colour .
❷
❶
d.
Press Menu. Press ▲ repeatedly to enter the
last two digits of the year, and then press OK.
Press ▲ or ▼ to choose
(e.g. Enter 07 for 2007.)
e.
Repeat for Month and Day, and Hour and Minute in
24-hour format.
Press ▲ or ▼ to choose
f.
Press Stop/Exit.
Note
If you make a mistake and want to start again,
press Stop/Exit to go back to step a.
Quick Setup Guide
DCP-135C DCP-150C
DCP-153C DCP-157C
c.
Press and slide the
paper side guides
❶
and paper length
❶
❷
guide to fit the
paper size.
❷
2
a. c. Press ▲ (Yes) to confirm the
When the LCD shows this
language setting.
message, press OK.
Note
・If you set the wrong
b.
Press ▲ or ▼ to choose
language, you can change
your language and press
it again after setting the
OK.
date and time.
(For details see Changing
LCD language in
Appendix B of the User's
Guide.)
g.
Lift each lock release lever and gently push it
until it clicks, and then close the ink cartridge
cover.
Note
The machine prepares the ink tube system.
This process will take approximately four minutes.
Turn the sheet over.