Network and general settings 5.4.7 Seats 5.4.8 Date and time 5.4.9 Upgrade Participants Switch system on/off Battery & Signal Logging System info 5.10 Logout Wireless Access Point LED behavior Troubleshooting Customer service Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
(in accordance with the European Waste Electrical and Electronic Equipment Directive). To dispose of old electrical or electronic devices, you should use the return and collection systems put in place in the country concerned. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
The purpose of this manual is to provide information required for configuring, preparing, and managing the DICENTIS Wireless Conference System. This manual describes in general how to use the Wireless Access Point (DCNM-WAP) web interface. If required, refer to the Hardware Installation Manual and Wireless Devices User Manual of the DICENTIS Wireless Conference System.
The DICENTIS Wireless Conference System is a “standalone” IP based system. It uses WiFi IEEE 802.11n for wireless distribution and processing of audio and data signals. For an overview of the system, please refer to the DICENTIS Wireless Conference System installation manual.
Opera. – Chrome. Preconditions – All used system devices are prepared and installed as described in the DICENTIS Wireless Conference System installation manual. Also see System overview, page 6. – The Wireless Access Point (DCNM-WAP) is powered on. – On a PC/laptop, make sure Windows PC DNS‑SD is installed (DNS‑SD is supplied on the media delivered with the DCNM-WAP).
Log in to the web application Enter the correct user name and password, select the required language, and click Login. The web interface homepage is displayed. See Web interface application, page 10. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
If another WiFi system is in subscription mode, this will also activate the overlap period in the DCNM-WAP. When all Wireless Devices are subscribed, disable the Subscription mode in the web interface application. The subscription mode will automatically switch off after 2 minutes. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
To set the identification mode for the system. Prepare meeting To create participants: – Give participants a name. Participants – Give participants an NFC-ID. – Assign seats to participants. See Participants, page 23. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Page 11
Configure or Manage the Wireless Devices loudspeaker volume. meeting Master volume See also – Login, page 8 – Users, page 17 – Seats, page 20 – Switch system on/off, page 24 Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Click the trash can to remove a seat from the Waiting list or Speakers list. Master volume control button Click the master volume control button to adjust the audio output level of the Wireless Devices loudspeaker and Wireless Access Point. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Allow participants to switch off their microphone: When selected, participants are allowed to switch off their microphone. – Show Possible To Speak: When selected, the white light in the Wireless Device microphone request button might be lit. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Page 14
– Stop all speakers and remove all waiting participants: When selected (grey), it cancels all speakers and requests when the device priority button is used. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Resume button: Allows voting to be resumed. Votes can be cast or changed. This button changes to the Hold button when it is pressed. – Close button: Closes the voting round. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Sweep tone. Click the Off button to stop the test tone. – When Send test tone to loudspeakers is selected, generates the selected test tone to the connected Wireless Devices loudspeaker. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Note: Only possible if your PC/laptop or tablet device is connected via the wired Ethernet connection of the DCNM-WAP. Notice! Ensure that the Bosch Onvif Camera has firmware 5.80 or higher. – A trash can is displayed next to the Camera name for removing a selected camera.
Go to Manage license and upload the request file from the USB memory stick. – Save the Response file to your USB memory stick. In the DICENTIS web interface application, click the Process response message button. Select the correct Response file, and then click Open. –...
Wireless Device are on when the Wireless Device does not have a subscription. – Remove disconnected seats button: Removes all seats which are currently not connected to the system. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
– As soon as the DCNM-WAP is upgraded, it will reboot. Exit the Upgrade page after completion of the upload process (Done state). Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Page 22
The following conditions apply: – The filename must start with DCNM-WDE – Only upload PNG files with dimensions of 480 x 272 pixels. Other file formats and dimensions are not supported. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Name: The participants (editable) name. – NFC‑ID: The number of the Near Field Communication (NFC) tag of the participant. – Seat: Selects the seat name, from the list, that the participant is assigned to. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
Wireless Devices will continue to work if the DCNM-WAP decides to switch to another WiFi channel in case of interference. – Serial number: The serial number of the Battery Pack. 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
Ethernet MAC and IP address. – Wireless IP address. – Software Versions. 5.10 Logout Preconditions: – None Click the Logout button to log out, which returns you to the Login page. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...
– Subscription mode is on. – At least one DCNM-WD(E) is connected. Flashing – System is in Power off mode. – No DC power supply connected. Table 6.1: Status LEDs 2015.03 | V1.0 | Configuration manual Bosch Security Systems B.V.
DICENTIS Troubleshooting | en Troubleshooting Customer service If a fault cannot be resolved, please contact your supplier or system integrator, or go directly to your Bosch representative. Bosch Security Systems B.V. Configuration manual 2015.03 | V1.0 |...