Advertisement
B. Remove nut at top of sink strainer Remove
extension
pope.
C. Loosen the large-diameter
nur at the base
of the strarner by placmg the tip of d
screwdwer
on the rldjr
of the nut and
gently tapp~nj
the wrwdrlver
~0th a
hammer
8
Attach the
upper
mounting
~wo,'mg
,om?::?k:p!!ond
rub&r
gasket, tin
the metal bsck-up
ring
(flat side up), up and over sink flange.
D. Remove nut
E. Push the straner assembly up through the
sink hole and remove
5
Clean sink's
drain line.
If installing
in a new home,
go to Step 6.
Remove drain trap. Using anaujer,
clean out
the horlzcmtal
drain pope that run5 from the
trap to the main waste pipe.
6
Separate the
mounting
assembly.
A
Holdlnj
the mountlnj
assembly with one
hand, "se the other hand to ,nsert,am-
breaker wrench
Into one of the lugs of the
lower mounting
rlnj
Turn assemblycounter-
clockwse
and remove
B. Loosen scr-
on mountmg
assembly until
the/ are level with mountlnj
rung surface
c. Use ScrewdrIver
to pry off snap r,ng
D. Take assembb
apart and set aslde
7
Apply rubber
asket
s
or putty
o sink flange. ,?
a
The rubber sink flange gasket should alway;
be used where powble
Place rubber
gasket over sink flange Go to Step 7-C
B. If slnkopenmj
does not permit the "se of a
rubber seal, plumb&
putty may be used
Form putty rntoa long roll by roll~nj It
behveen
your hands Press roll under sink
flange nm
C. Place flange Into sink drain hole. Fust down
gently, but flrmb to make sure flange sits
evenly over gasket or I" putty
B. Holdmj
ttx rubber gasket and metal back-
up nng in place, attxh
the mwntlng
ring to
the sleedve wth the three mounting
rrnj
screw-s Do Not bqhten screws at this t!me.
C. Push rubber gasket, metal back-up
n"g and
mounmg
rmg further up sink sleeve. Slrde
snap ring wto
srnk sleeve untrl It pops Into
place I" the sleeve groove.
D.Tijhten
mounting
scr-
until entlre
mounting
assembly IS seated evenly and
tkhtlvawnst
sink
9
Make
electrical
connections.
A
Remove electrical
plate from the bottom
of the new disposer
Pull out the black end
Vmrte electrical
wires
Locate the green
jroundnj
screw under plate.
8. Insert strain relref Into hole Insert power
supply cable through strain relief. Pull cable
wres through open~nj
where dlswser
wres are located. nghten
strain relref
1D.H
screws.
c. Connect power supply cable bwres to the
disposer wires us~nj electrical
wire nut5 M
connectwhiietotiite,andbbckto
1)s
by solderlnj
wires together
Be SUR to
black. Wrap wore conratlcns
with
,
,,
electrical
tape. Put wires back inside
drsooser housmq.
10
Check for
proper
grounding.
Electrical
ground
is required
on this
appliance.
Do NOT reconnect
eletical
CUrTent to
main service
panel
until
proper
ground
Is installed.
k If the cabk
kadlng
to the dlswser
has
three wires, attach tine green groundlnj
we
to the green groundlng
xre.v
Go to
Step 10-D.
B. If the cable does NOT have a grounding
wire, attach a length of copper
wire (no
smaller than the other cable wire) to the
jreen grcwndmg
screw
C. Attach theotherend
of thegrwndmj
wire
to a grounded
metal cold water pipe!
DO NOT ground
to a gas sUpply line of
hot water
supply
Ilne.
Use grounding
clamp to secure wire to
pipe. If noa-meta
or plastrc pipe IS used in
water connections
or water supply, you must
have a qwlified
electrtcian
install a proper
ground.
PANEL
B
Hide quick links:
Advertisement
