Page 1: Table Of Contents
VIDEO CASSETTE RECORDER HR-J655EA TV/VCR AUDIO DISPLAY (MONITOR) DAILY WEEKLY C. RESET CANCEL TIMER START STOP DATE PROG EXPRESS PROGRAMMING PROG. 30 SEC PROG. CHECK A. DUB/ TIMER SIMUL POWER PUSH JOG COUNTER RESET VIDEO (MONO) L–AUDIO–R TV PROG SP/LP/EP...
Page 2: Safety First
ABOUT HEAD CLEANING Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or inter- rupted. Be sure to contact your nearest JVC dealer if such troubles occur. Auto Head Cleaner A built-in head cleaner automatically cleans the video heads and head drum whenever a tape is loaded or unloaded to reduce head clogging.
Page 3: Installing Your New Recorder
INSTALLING YOUR NEW RECORDER Basic Connections Aerial terminal RF Cable (provided) Back of TV AV-IN terminals AV Cable (not provided) Mains Power Cord AUDIO OUT/ Mains outlet VIDEO OUT Connect the power plug to an AC outlet before installing the lithium battery.
Page 4: Initial Settings
Video Channel Set Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. TEST SIGNAL The channel on which the screen to the left appear clearly in step 3 is your Video Channel.
Page 5 If you cannot obtain the two vertical white bars clearly with any channel between 28 and 60, consult your JVC dealer. FINISH VIDEO CHANNEL Press OK. If Auto Set Up ( pg.
Page 6: Auto Set Up
Auto Set Up IMPORTANT Don't press any buttons on the recorder or remote that are not directly related to the step you are performing while Auto Set Up is in progress. If you perform Auto Set Up successfully during installa- tion, there's no need to separately perform the Clock Set or Channel Set procedures, but if adjustments become necessary they can be performed as follows:...
Page 7 DO NOT press any button on the recorder or remote control while Auto Set Up is in progress. AUTO CH SET PLEASE WAIT START During Auto Set Up "PLEASE WAIT" blinks on the screen and "Auto" blinks on the front display panel. NOTES: If you perform Auto Set Up when the aerial cable is not connected properly, "SCAN COMPLETED -NO SIGNAL-"...
Page 8: Clock Set
Clock Set Turn on the TV and select the VIDEO channel (or AV mode). MENU PUSH JOG NOTE: If the year digits are automatically cleared, it is possible that you have input 29th February for a non-leap year. Input the correct data. INITIAL SETTINGS (cont.) TURN THE RECORDER ON Press...
Page 9: On-Screen Displays
On-Screen Displays Turn on the TV and select the VIDEO channel (or AV mode). MENU The superimposed indication on the TV screen tells you what the recorder is doing. PR. 12 21 : 00 24. 12. 98 HIFI –1 : 23 : 45 You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF.
Page 10: Playback
Basic Playback Turn on the TV and select the VIDEO channel (or AV mode). COLOUR SYSTEM The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
Page 11: Playback Features
Playback Features PAUSE ATTENTION In the search, still, slow-motion or frame-by-frame playback mode, the picture will be distorted. the noise bars will appear. there will be a loss of colour with an LP-recorded tape. Variable-Speed Search To resume normal playback, press PLAY. Still Picture/Frame-By-Frame Playback To resume normal playback, press PLAY.
Page 12: Manual Tracking
REVIEW Manual Tracking Your video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. TV PROG 30 SEC PAUSE PUSH JOG NOTE: When a new tape is inserted, the recorder enters the automatic tracking mode automatically.
Page 13: Index Search
Index Search Your recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode. ACTIVATE INDEX SEARCH Press PUSH JOG (™...
Page 14: Soundtrack Selection
Soundtrack Selection Your video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select. During Playback Pressing AUDIO changes the soundtrack being played back as follows: AUDIO Recorder's Front Panel L + R NORM L + R + NORM...
Page 15: Recording
RECORDING Basic Recording Turn on the TV and select the VIDEO channel (or AV mode). RECORD TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. NUMBER TV PROG SP/LP/EP...
Page 16: Recording Features
Recording Features C.RESET RECORD Record One Programme While Watching Another Elapsed Recording Time Indication You can check the exact time of a recording. DISPLAY NUMBER Instant Timer Recording (ITR) TV PROG This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min.
Page 17: Simulcast Recording
Receiving Stereo And Bilingual Programmes Your recorder is equipped with a Sound-Multiplex decoder (A2) making reception of stereo and bilingual broadcasts possible. When the channel is changed, the type of broadcast being received will be displayed on the TV screen for a few seconds. Type of Broadcast On-screen Display Being Received...
Page 18: Picture System
B.E.S.T. Picture System Turn on the TV and select the VIDEO channel (or AV mode). PLAY RECORD MENU The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
Page 19: Start Recording
Recording START RECORDING Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder. DURING B.E.S.T. B.E.S.T. COMPLETE The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording. NOTES: The B.E.S.T. system works for both SP and LP (or EP) modes only after a tape has been inserted and the Record mode is first initiated.
Page 20: Timer Recording
Setup CODE Turn on the TV and select the VIDEO channel (or AV mode). MENU The G- CODE input channel, date, start and stop time data when setting the timer record function. Simply key in the G- TV programme you wish to record (found in most TV listings) and the recorder’s timer is automatically programmed.
Page 21 MENU PUSH JOG ENTER RECEIVING CHANNEL POSITION NUMBER Press PUSH JOG %ﬁ or NUMBER keys to input the number of the recorder's channel position on which the Guide Program NUMBER number's broadcast is received. Then press OK or PUSH JOG If the satellite broadcast is received on your recorder's auxiliary channel "L-1", select "L-1"...
Page 22: G- Code Timer Programming
Timer CODE Programming Before performing G- Timer Programming: CODE Be sure to read "G- Setup" ( CODE Insert a cassette with the safety tab in place. The recorder will come on automatically. Turn on the TV and select the VIDEO channel (or AV mode).
Page 23 NUMBER STOP+/– PROG. RETURN TO NORMAL SCREEN Press PROG. or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. Repeat steps 1 – 5 for each additional programme. ENGAGE RECORDER’S TIMER MODE WEEKLY Press TIMER. The recorder turns off automatically and TIMER ‰...
Page 24: Express Timer Programming
Express Timer Programming Remember, the clock must be set before you can programme the timer ( pg. 8). Before performing the following steps: Insert a cassette with the safety tab in place. The recorder will come on automatically. Turn on the TV and select the VIDEO channel (or AV mode).
Page 25 PROG. RETURN TO NORMAL SCREEN After confirming all information is correct, press PROG. or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. Repeat steps 1–8 for each additional programme. ENGAGE RECORDER’S TIMER MODE WEEKLY TIMER Press TIMER.
Page 26 CANCEL START+/– PROG. MENU Check, Cancel And Replace Programmes TIMER TV PROG+/– PUSH JOG To cancel or replace a programme... TIMER RECORDING (cont.) DISENGAGE TIMER MODE Press TIMER, then press ACCESS PROGRAM CHECK SCREEN Press PROG. CHECK. PR START STOP 8:00 10:00 10:00 10:45 11:30 13:00...
Page 27: Auto Sp Lp Timer
Auto SP LP Timer If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. For Example . . . Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape Approximately 150 minutes Approximately 60 minutes...
Page 28: Special Features
NUMBER "1" STOP Remote A/B Code Switching The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals.
Page 29 TIMER TV VOL+/– IMPORTANT Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability. TV BRAND NAME...
Page 30: Compatibility
MESECAM mode. The playback picture will always be monochrome. In the NTSC4.43 mode, with some TVs, on-screen displays (Program screen etc.) may roll up or down and there may be a loss of colour. When this happens, select the AUTO mode. HR-J655EA Multi-system tuner (B/G) Mode Description Usually set to this mode.
Page 31: Tape-To-Tape Editing
TV system you have selected at the TV System Select screen. Tape-To-Tape Editing There are 4 different types of recorded tape, depending on the signal recorded. Recorded tape MESECAM SECAM NTSC HR-J655EA Built-in RF converter (G) Playback equipment HR-J655EA MESECAM Recording circuit SECAM NTSC 3.58 MHz...
Page 32: Editing
Edit To Or From Another Video Recorder NUMBER "0" TV Receiver Player AV Cable VIDEO (not provided) CHANNEL RF Cable (provided) Recorder You can use your video recorder as the source player or the recording deck. NOTES: All necessary cables can be obtained from your dealer. NTSC tapes being played back in the NTSC [ PAL mode When you dub an NTSC tape using your recorder as the playback deck, select NTSC 3.58 (or NTSC 4.43) with the...
Page 33: Edit From A Camcorder
AUDIO/VIDEO input connectors. Use the L connector for monaural connection. When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder’s instruction manual for operating procedure.
Page 34: Audio Dubbing
Audio Dubbing CD Player etc. CD Player etc. Mixer output Audio mixer Original sound AUDIO OUT NOTES: When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the mixed sound (Hi-Fi + Normal soundtracks), press AUDIO on the remote control to select "...
Page 35: Tuner Set
TUNER SET Turn on the TV and select the VIDEO channel (or AV mode). MENU IMPORTANT Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( you have moved to a different area or if a new station starts broadcasting in your area.
Page 36: Manual Channel Set
MENU Manual Channel Set Store channels that were not stored during Auto Set Up ( or Auto Channel Set ( PUSH JOG TUNER SET (cont.) pg. 35). ACCESS TUNER SET SCREEN Perform steps 1 – 3 of "Auto Channel Set" on page 35. ACCESS CHANNEL LIST Press PUSH JOG %ﬁ...
Page 37: Delete A Channel
CANCEL MENU Delete A Channel ACCESS TUNER SET SCREEN Perform steps 1 – 3 of "Auto Channel Set" on page 35. ACCESS CHANNEL LIST NUMBER Press PUSH JOG %ﬁ to place the pointer next to "CH EDIT", then press OK or PUSH JOG SELECT CHANNEL Press PUSH JOG %ﬁ...
Page 38: Swap Channel Positions
Swap Channel Positions Example:To swap CH03 and CH09. ACCESS TUNER SET SCREEN Perform steps 1 – 3 of "Auto Channel Set" on page 35. ACCESS CHANNEL LIST Press PUSH JOG %ﬁ to place the pointer next to "CH EDIT", then press OK or PUSH JOG SELECT POSITION (e.g.
Page 39: Questions And Answers
QUESTIONS AND ANSWERS PLAYBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
Page 40: Troubleshooting
Press TV PROG + or – a few times to remove the noise bars from the screen. Engage and adjust tracking manually. pg. 12) Consult your JVC dealer. Select the correct colour system by pressing the COLOUR SYSTEM button. ( pg.
Page 41 RECORDING SYMPTOM 1. Recording cannot be started. 2. TV broadcasts cannot be recorded. 3. Tape-to-tape editing is not possible. 4. Camcorder recording is not possible. TIMER RECORDING SYMPTOM 1. Timer recording won’t work. 2. On-screen timer programming is not possible. 3.
Page 42: Other Problems
OTHER PROBLEMS SYMPTOM 1. Whistling or howling is heard from the TV during camcorder record- ing. 2. When scanning channels, some of them are skipped over. 3. The channel cannot be changed. 4. Channel settings that were made manually seem to have changed or disappeared.
Page 43: Index
INDEX FRONT VIEW A DUB/ TIMER SIMUL POWER VIDEO ( MONO ) L–AUDIO–R TV PROG TV PROG 1 POWER Button pg. 8 2 TIMER Button pg. 23, 25 3 Audio [A.] Dubbing [DUB] Button SIMUL Button pg. 17 4 Cassette Loading Slot 5 REVIEW Button pg.
Page 44: Display Panel
DISPLAY PANEL 15dB NORM 1 B.E.S.T. Picture System Display Audio Level Indicator 2 Symbolic Mode Indicators STILL: SLOW: PLAY: FF/REW VARIABLE RECORD: SHUTTLE SEARCH: RECORD PAUSE: AUDIO DUBBING: AUDIO DUBBING PAUSE: pg. 18 3 "Timer" Indicator 4 Channel Display Clock Display 5 Tape Speed Indicators 6 Instant REVIEW Indicator 7 Audio Mode Indicator...
Page 45 The remote control can operate not only the video recorder but also some of your TV's functions. To operate your video recorder, first press the VCR button to set the remote control to the Video mode. To operate your TV, first press the TV button to set the remote control to the TV mode (...
Page 46: Specifications
GENERAL Power requirement : AC 220 – 240 V`, 50/60 Hz Power consumption : 24 W Temperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 401 x 94 x 340 mm Weight : 3.8 kg Format...
Page 47 MEMO...

JVC HR-J655EA Instructions Manual

Safety First

Installing Your New Recorder

Initial Settings

Playback

Recording

Timer Recording

Special Features

Information on Multi-System

Compatibility

Editing

Tuner Set

Questions and Answers

Troubleshooting

Index

Specifications

Quick Links

Related Manuals for JVC HR-J655EA

Summary of Contents for JVC HR-J655EA

Table of Contents