Table of Contents
Advertisement
When local codes..
B.
Permit
the
use of a flexible-type
power
supply
cord
(pigtail)
but
Do Nol permrt
connecting
cabrnet-
grounding
conductor
to the
neutral
wire
of the power
supply
cord:
Ungrounded
neutral
Figure
6
Connect
seporole.
copper
grounding
wire
(No.-10
minimum)
from
external
grounding
connector
to approved
ground.
I, Disconnect
Ihe power
supply.
2. Remove
the
power
supply
cord
equipped
with
the washer/dryer
as
instructed.
See Panel
F, "To remove
the power
supply
cord
"
3. Install
a three-wire
power
supply
cord
(See
"Electrical
Requirements",
Panels
A and
B) through
the 314'.
U.L -lIsted
strain
relief
4. Connect
the
neutral
wire
(white)
of the
power
supply
cord
and
the
internal
grounding
wire
(green
with
yellow
stripes)
to the center.
sliver-
colored,
terminal
screw
of the
terminal
block
Connect
the
other
wires
to the outer
terminals.Tighten
screws
firmly
(See Figure
6 1 For
@an-end
wares, see'To
connect
connection:
Panel
G.
5 Connect
a separate
copper
grounding
wire (No. IO minimum)
See "To connect
a separate
grounding
wIrerPanel
F for
detolled
Instructions.
6. Replace
the terminal
block
cover.
When local codes...
c.
Do Not permit
the
use of a flexible.
three-wne,
power
supply
cord
and
Permit
three-wire.
copper
power
supply
cable
and
Permit
connecting
the
cabinet-
grounding
conductor
to the
neutral
w!re
of the
power
supply
cable:
tnternat grounding
wire (green with
yellow rlrip%r)
\
center.
silver-colored.
,*,mtnat
block
screw
and
neutral
white
wile
When
local codes...
D
n
Do Not oermit
the use of three-wire.
flex!bie.'power
supply
cord
and
Permit
three-wire.
copper
Power
supply
cable
but
Do Not permit
connecting
the
cabinet-grounding
conductor
to
the
neutral
wire
of the
power
supply
cable:
Cente,.
rllver-colored.
terminal
block
screw
Sepmate
and
neutral
while
wtre
copper
grounding
Internal
groundtng
\ wtre
\
wtre (green
with
yellow
stripes)
Grounded
neutral
Figure
7
I. Disconnect
the power
supply
cord.
2 Remove
the
power
supply
cord
equipped
with
the washer/dryer
as
Instructed.
See "To remove
the
power
supply
cord-.
Panel
F.
3. Install
copper
power
supply
cable
(See
"Electrical
requirements".
Panels
A and
8) through
the 3/4'.
U./L.-listed
strain
relief.
4 Move
the internal
grounding
wire
tareen
with
vellow
stripes)
from
i6e center,
s&er-colo;ed.
terminal
block
screw
to the external
grounding
connector.
5 Connect
the neutral
wire
(white)
of the flexible,
armored
or
non-metallic
sheathed,
cooper.
power
supply
cable
to the
center.
silver-colored,
terminal
screw
of the
terminal
block.
Connect
the
other
wires
to the outer
terminalsTighten
the screws
firmly
See Figure
7. For
plain-end
wires,
see "To connect
connection.'
Panel
G.
6. Replace
the terminal
block
cover.
Ungrounded
neutral
Figure
8
Connect
saparale,
copper
grounding
wire
(No.-10
minimum)
from
external
grounding
connector
to approved
ground.
1, Disconnect
the power
supply.
2. Remove
the
power
supply
cord
equipped
with
the washer/dryer
as
Instructed.
See "To remove
the
power
supply
cord",
Panel
F.
3 Install
copper
power
supply
cable
(See
"Electrical
requirements".
Panels
A and
B) through
the
3/4'.
U.L.-listed
strain
relief.
4 Connect
the
neutral
wire
(white)
of the flexible,
armored
or
non-metallic
sheathed.
copper.
power
supply
cable
and
the
internal
grounding
wire
(green
with
yellow
strrpes)
to the center,
silver-colored.
terminal
screw
of the terminal
block.
Connect
the other
wires
to the outer
terminals,
Tighten
screws
firmly.
(See
Fiaure
8.1 For olain-end
wires.
see
V~
"Direct
wiring
cOnneC~lOn.~
Panel
G.
5. Connect
a separate.
copper.
grounding
wire
(No.-10
minimum).
See '~To connect
a separate
grounding
wire'
, Panel
F. for
detailed
Instructions.
6 Replace
the terminal
block
cover.
Direct wiring
connection
1. Disconnect
the power
supply.
2 Strip the outer
covering
back
3
inches
from
the
end
exposing
the
three
wires.
-II
ps-4
LIZ
i
-il't
Plain-endwirlng
Figure
12
3. Srrlp the
Insulation
back
1 inch
from
the
end
of each
wire.
Form
the
bare
wires
into
a "U"-shaped
hook.
4. Loosen.
Do Not remove.
screws
from
terminal
block.
Attach
wires
according
to instructions
for type
of
connection
needed
5. Slide the
end
of each
wire
under
the screw
head
with
the open
side
of the screw
hook
on the right.
Squeeze
the wire
together
to form
a
loop.
6 Tighten
each
screw
firmly.
7. Tlghten
strain
relief
screws.
Panel G
Advertisement
Table of Contents
