General Safety Instructions For Power Tools - Craftsman 113.232210 Owner's Manual

NTER/PLANER
due to a
of charge.
CONTACTING THE NEAREST SEARS SER-_
J
while this product is used in the United States.
rights, and you may also have other rights which
ROEBUCK AND CO. Dept: 698/731A. Sears Tower, Chicago, IL 60684
;:;I GENERAL SAFETY iNSTRUCTiONS FOR POWER TOOLS
KNOW;YOUR POWER TOOL
Read and understand the owner_ manual and
labels affixed to the tool. Learn its application and
limitationsas well as the specific potential hazards
peculiar to this tool.
2; GROUNDALL TOOLS
12, USE SAFETYGOGGLES [HEAD PROTECTION)
Wear safety goggles (must comply with ANSI
Z87.1 ) at all times. Everyday eyeglassess are not
safety glasses. They only have impact resistant
lenses. Also, use face or dust mask if cutting oper-
ation is dusty, and ear protectors (plugs or muffs)
_ . This tool is equipped with an approved 3-conductor during extended periods of operation.
_ ::i:_ cordanda 3-pr0nggr0unding type :plugto fit the 13, SECURE WORK
proper grounding receptacle. The green con- Use clamps or avise tO hold work when practical.
ductor _inthe cord: is:the: grounding wire, Never It frees both hands to operate tooll
" i _ connect the green wire to a live terminal. 14, DON'T OVERREACH
_3; KEEPGUARDS INPLACE " Keep proper footing and balance at all times.
i : i_i _ln wo[kingl order, and in: proPer adjustment and 15. MAINTAIN TOOLS WITH CARE
!. alignment; Keep tools sharp and clean for best and safest
:performance. Follow instructionsfor lubricating and
I::'_ _. _:i! ::_ :;:: :_i _::_ i ::::: _:';i; : NEVERSTAND ON TOOL OR ITS STAND ;i _i:: ._ ::!
........... SH0_ ICHIL_ROOF _ Sed0us!njU_could occur if the toot is tipped or ff
i i_ maste_switchesilby removing star-_ CUtting:tool is accidentally contacted: Do not' ....
;_:':' 5ring tools where: children Can_ get:: :: ::_:, ::store, materials above or near the tool such that it
;_'_.... ;_'_::_ ::_ i;_: i_ is;tieCessaryto standon the to01 or its;stand to
::i _I:_ : :reachthern_ ::; ...... : :
job better and safer at the rate for _2o;: CHECK DAMAGED PARTS
1: it was designed:: :i : : _: ::: Before furtheruse of the tool, a guard or other part
:: ::i thatJs damagedshouid be carefully checked to
:_::_i:::;:::::i::i _; D on;t for_i:io01s 0_ _achment to do a job it was :_ :_: ensure::that it:wi!l operate properly and perform its
i_:::: intended Tunction:Check for alignment ol" moving
_::: ::::_::i_::: .... .... _ :_ .... ' ...... : parts, bfndlngor mowng parts, breakage of parts,
"_ _ _"....... "': ......... ' _" : : ..... ......... .................... m ountin ..... .... "
_;::::_ :::_:;_!;::D6 _ ov_ :_nec_ies _ :or:: :: ::: g; ana any other conditions that may anect
_:: :';:_i_:i;;:r_,_': _ri_+:_ _n t*.t _.nht_inrnov . : : =tsoperat;on. A guardor other part that =sdamaged
_:' _ ......... ............. ................... : ...... _ ...... _ n d : • should be properly repaired or rep aced
e de ;: _::: ::: .........: ....
::: 21;: NEVERLEAVETOOLRUNNING UNATTENDED
; ::: =_:';:R_i _ge ............. :el_w: .......... ; .....' ............... Turn power off Don't leave toot untl it comes to a
complete stop.