Table of Contents
Advertisement
612547-329
i:i_i
q
SEARS
OWNERS
MANUAL
MODEL NO.
315.117130
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
SAVE
THIS
MANUAL
FOR
FUTURE
REFERENCE
CRAFTSMAN"
3 INCH
BELT SANDER
DOUBLE INSULATED
Introduction
Operation
Maintenance
Repair Parts
Designed exclusively
for and sold only by
SEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684
612547.329
PRINTED
IN
U,$,A,
10-86
Advertisement
Table of Contents
Related Manuals for Craftsman 315.117130
Summary of Contents for Craftsman 315.117130
- Page 1 612547-329 SEARS OWNERS MANUAL MODEL NO. 315.117130 i:i_i CRAFTSMAN" CAUTION: Read Rules for 3 INCH Safe Operation and Instructions BELT SANDER Carefully DOUBLE INSULATED Introduction SAVE THIS MANUAL Operation Maintenance FUTURE REFERENCE Repair Parts Designed exclusively for and sold only by SEARS, ROEBUCK AND CO., Dept.
- Page 2 FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT SANDER If this Craftsman Belt Sander falls to give complete satisfactiori within one year from the date of pur- chase RETURN IT TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES and Sears...
- Page 3 RULES FOR SAFE OPERATION (Continued) 10. WEAR PROPER APPAREL. No loose clothing or jewelry to get caught in moving parts. Rubber gloves and footwear are recommended when working outdoors. Also, wear protective hair covering to contain long hair. 11. USE SAFETY GLASSES with all tools.
- Page 4 OPERATION ..REAR TRACKING SCREW Make sure power supply is 110-120 volts, 60 HZ, AC only. HANDLE Before attempting to u_e your Sander, familiarize yourself with al{ operating features (See Figure and safety requirements, FRONT IDLER SANDING PULLEY BELT , iHi i,l,i iim,iH LOCK "ON"...
- Page 5 OPERATION Selecting the correct size and type sanding belt Is an important step tn achieving a high quality sanded LIFT TENSION RELEASE LEVER TO REMOVE finish. Standard 3 inch x 21 inch sanding belts made SANDING BELT of alumi'num oxtde, silicone carbide, and othel' syn- thettc abrasives are best for power...
- Page 6 OPERATION ALWAYS WEAR SAFETY GLASSES SANDING EYESHIELDS WHEN OPERATING YOUR SANDER. BELT To adjust sanding belt, connect Sander to power supply. Place Sander in upside down position shown in Figure 7. NOTE: This position is for ad- justments only. The Sander is not in an operating position.
- Page 7 MAINTENANCE WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. TIMING BELT REPLACEMENT DISCONNECT SANDER FROM POWER SUPPLY BEFORE SERVICING WHEN REPLACING TIMING BELT, USE REPLACE- MENT BELT NUMBER 989368-000 ONLY. See Key Number 5 on Parts List, Page 11. S _EMALL PULLEY TIMING BELT Remove sanding belt from sander.
- Page 8 CORD REPLACEMENT DISCONNECT THE SANDER FROM POWER SUPP. BEND LY WHILE REPLACING PARTS OR MAKING AD. JUSTMENTS. 1. Remove handle cover and screws as described on Page 7. Note the locations of all wiring in the handle and how each connection is made to the cord.
- Page 9 Cat. No. 9 23203-Medium Cat. No. 9 22302.Medium Cat. No. 9 23204-Coarse Cat. No, 9 22303-Coarse CRAFTSMAN Cat, No. 9 22305.X.Coarse Dustless Sanding Attachment 9 11766 CAUTION: The use of attachments or accessories not listed above might be hazardous, NOTES...
- Page 11 ..° ....• ....° • ..° ..• ° ..• I1 ..• ° ..° "1- ... '.--_ ' " _ "_" ..al m _..: : : •...
- Page 12 " CRRFTSMRN SEARS 3 INCH OWNERS BELT SANDER MANUAL DOUBLE INSULATED SERVICE that have purchased your Belt Sander, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts...