Advertisement
MW.
MEAN WELL
25W Dual Output Switching Power Supply
@ Features :
* Universal AC input / Full range
* Low leakage current<0.5mA
* Cooling by free air convection
* 100% full load burn-in test
Fixed switching frequency at 100KHz
* Low cost
High reliability
* 2 years warranty
p D-25
series
* Protections: Short circuit / Overload / Over voltage / Over temperature
A\.;|4/=|CBCE
SPECIFICATION
MODEL
PD-25A
PD-25B
PD-2505
PD-2512
PD-2515
OUTPUT NUMBER
CHt
CHt
CH2
CHt
CH2
CHt
CH2
2.5A
2.5A
1A
1A
0.8A
0.8A
0.2~2A
0.1~3A
|0.1~2.5A |0.1~1.2A |0.1~1.2A [0.1~1A
[0.1~1A
iarerowen
Jaton 25.2W
a
24W
24W
OUTPUT
50mVp-p
| 200mVp-p
50mVp-p
|50mVp-p
|50mVp-p
|50mVp-p
| 50mVp-p
[2.0% |
oe
+2.0%
cn
0%
+6.0%
[+40%
|[+4.0%
|+4.0%
| +4.0%
+0.5%
+0.5%
[+2.0% |
+1.0%
|+05%
|[+05%
|+0.5%
| +0.5%
LOAD REGULATION
+1.0%
+4.0%
|+4.0%
[440%
|+3.0%
|+3.0%
[43.0%
|+3.0%
260ms, S0ms/230VAC
_ 250ms, 30ms/t15VAC at ful oad
HOLD UP TIME (Typ.)
100ms/230VAC
16ms/115VAC at full load
VOLTAGE RANGE
85~264VAC
120~370VDC
FREQUENCY RANGE
47 ~ 63Hz
SIPUT
71%
77%
'| 73%
74%
75%
AC CURRENT (Typ.)
O.65A/115VAC
_0.4A/230VAC
INRUSH CURRENT (Typ.)
COLD START 32A
LEAKAGE CURRENT
<0.5mA/ 240VAC
Above 105% rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
5.75 ~ 6.75V|
13.8 ~ 16.
5.75 ~ 6.75V|
27.6 ~ 32.4V|
5.75 ~ 6.75V}
5.75 ~ 6.75V) 13.8 ~ 16.2V |-13.8 ~ -16.2V/17.3 ~ 20.3V hi73 ~ -20.3V
PROTECTION | OVER VOLTAGE
Protection type : Shut off o/p voltage, clamping by zener diode
Tj 135°C typically (U1) detect on main control IC
OVER TEMPERATURE
;
Protection type : Shut down o/p voltage, re-power on to recover
WORKING TEMP.
-10 ~ +60'C (Refer to "Derating Curve")
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT | STORAGE TEMP., HUMIDITY | -20~+85°C, 10 ~ 95% RH
TEMP. COEFFICIENT
+0.03%/'C (0 ~ 50°C) ON CH1 output
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 approved
SAFETY & | WITHSTAND VOLTAGE
P-OIP:3KVAC
I/P-FG:2.0KVAC
O/P-FG:0.5KVAC
EMC
ISOLATION RESISTANCE
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/ 70% RH
(Note 4)
EMC EMISSION
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
fs
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5, light industry level, criteriaA
507.9Khrs min.
MIL-HDBK-217F (25°C)
OTHERS |DIMENSION —=————_| 107°61*28mm (L*W*H)
0.15Kg; 96pes/15.9Kg/1.3CUFT
|
NOTE
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to "EMI testing of component power supplies."
(as available on http:/Awww.meanwell.com)
5. Heat Sink HS1,HS2,HS3 can not be shorted.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
File Name:PD-25-SPEC
2013-08-08
Advertisement
