Related Manuals for Samsung DVE22N6850X/A2-00
Summary of Contents for Samsung DVE22N6850X/A2-00
- Page 1 Dryer User manual DVE22N6850** DV6800N_DC68-03650D-00_EN.indd 1 2018-01-31 12:43:02...
-
Page 2: Table Of Contents
Contents Safety information What you need to know about the safety instructions Important safety symbols Important safety precautions Warnings Cautions Before installation Key installation requirements Location considerations Ducting requirements Exhausting requirements Electrical requirements Installation What’s included Step-by-step installation Exhaust ducting guide Changing the direction of the exhaust duct (optional) Switching the door position Before you start... - Page 3 Maintenance Cleaning Troubleshooting Checkpoints Information codes Specifications Fabric care chart Protecting the environment Specification sheet Cycle chart English 3 DV6800N_DC68-03650D-00_EN.indd 3 2018-01-31 12:43:02...
-
Page 4: Safety Information
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. -
Page 5: Important Safety Precautions
WARNING • State of California Proposition 65 Warning (US only) This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. •... - Page 6 Safety information Before the appliance is removed from service or discarded, remove the door to the drying compartment. Do not reach into the appliance if the drum is moving. Do not install or store this appliance where it will be exposed to the weather. Do not tamper with internal controls.
-
Page 7: Warnings
WARNING - To reduce the risk of fire or explosion: • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode. Any material that has been in contact with a cleaning solvent or flammable liquids or solids should not be placed in the dryer until all traces of these flammable liquids or solids and their fumes have been removed. - Page 8 Safety information • Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product. • Clean the lint screen before or after each load. •...
-
Page 9: Before Installation
Before installation Read through the following instructions before installing the dryer, and keep this manual for future reference. WARNING The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - Do not contact these parts while the appliance is energized. - Page 10 Before installation NOTE When the exhaust duct is installed at the rear of the dryer, the rear must have at least 5.5 inch (140 mm) clearance. 5.5” (140 mm) Side by side installation 1 in. (25 mm) 25.8 in. (655 mm) 23.6 in.
- Page 11 27.1 in. (688 mm) 67 in. (1702 mm) 4.75 in. (120 mm) WARNING Samsung’s washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer. English 11 DV6800N_DC68-03650D-00_EN.indd 11 2018-01-31...
-
Page 12: Ducting Requirements
Before installation Ducting requirements Recommended Use only for short-run installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° Metallic Metallic Rigid Rigid elbows flexible* flexible* 80 ft. (24.2 m) 40 ft. (12.2 m) 60 ft. (28.3 m) 30 ft. -
Page 13: Exhausting Requirements
Exhausting requirements Outside the United States and Canada The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl • Refer to the local codes. space, or a concealed space of a building. WARNING Exhausting the dryer to the outside will •... -
Page 14: Electrical Requirements
Before installation Electrical requirements Grounding The wiring diagram is located on the plate under the control panel or rear frame. This dryer must be grounded. In the event of a malfunction or breakdown, the ground WARNING will reduce the risk of electrical shock by •... - Page 15 Electrical connections • Grounding through the neutral conductor is prohibited for (1) new Before operating or testing, follow all branch-circuit installations, (2) mobile grounding instructions in the “Grounding” homes, (3) recreational vehicles, and section. An individual branch (or separate) (4) areas where local codes prohibit circuit serving only your dryer is grounding through the neutral recommended.
-
Page 16: Installation
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the accessories, contact a local Samsung service center or the retailer. Dryer at a glance 01 Top cover... - Page 17 Accessories & tools Provided accessories DRYER STACKING KIT Stacking Kit Cover Plate (Canadian models only) Required tools Pliers Cutting knife Nut driver Level Phillips screwdriver Duct tape Wrench WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
-
Page 18: Step-By-Step Installation
Installation Step-by-step installation Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. STEP 1 Install the exhaust system Select a location and move the dryer to the site. For easy access, we recommend you install the dryer in the same location as your washer. - Page 19 STEP 2 Connect the electrical wiring First, read through the “Electrical requirements” section, and then follow the instructions on this page or the next page. Instructions for a 3-wire system are on this page. Instructions for a 4-wire system are on the next page. For a 3-wire system Loosen or remove the screws from the center terminal block.
- Page 20 Installation For a 4-wire system Remove the external ground connector’s screw, and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION • To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
- Page 21 • Insert the power cord with a UL-listed strain relief through the hole provided in the cabinet near the terminal block. • A strain relief must be used. • Do not loosen the nuts already installed on the terminal block. Be sure they are tight. •...
-
Page 22: Exhaust Ducting Guide
Installation STEP 4 Final Check When installation is complete, confirm that: • The dryer is plugged into an electrical outlet and grounded properly. • The exhaust ductwork is connected and the joints are taped. • You have used rigid or stiff-walled flexible metal duct material, not plastic flexible duct. •... -
Page 23: Changing The Direction Of The Exhaust Duct (Optional)
Changing the direction of the exhaust duct (optional) WARNING Before performing this exhaust installation, disconnect the dryer from its electrical supply. Wear gloves to protect your hands and arms from sharp edges when working inside the cabinet. Side venting Detach the right (A) or left (B) side knockout as desired. - Page 24 Installation Reconnect the cut portion of the duct (D), and then fasten it to the ramp on the appliance base with the screw (C) which you set aside in Step 2. Connect a duct to an elbow, and then tape the duct and the elbow together with duct tape.
- Page 25 Cover the back opening with a cover plate (G). WARNING Never leave the back opening uncovered. It must be covered with a cover plate. Bottom venting Detach the bottom knockout (A). Pull the duct out of the dryer, and then remove the screw (B) from the duct.
- Page 26 Installation Reconnect the cut portion of the duct (C), and then fasten it to the ramp on the appliance base with the screw (B) which you set aside in Step 2. Insert the elbow (D) through the rear hole and connect it to the duct (C). Rotate the elbow (D) through the bottom opening.
- Page 27 Cover the back opening with a cover plate (F). WARNING Never leave the back opening uncovered. It must be covered with a cover plate. English 27 DV6800N_DC68-03650D-00_EN.indd 27 2018-01-31 12:43:13...
-
Page 28: Switching The Door Position
Installation Switching the door position To reverse the direction of the door, we recommend that you contact a qualified technician. Unplug the power cord of the dryer. Remove the two hinge screws from the door, and then remove the door by lifting it up slightly. - Page 29 Locate and remove the 9 screws from the door as shown. Remove the door lever. Remove the door frame. English 29 DV6800N_DC68-03650D-00_EN.indd 29 2018-01-31 12:43:14...
- Page 30 Installation Rotate the door glass 180°. Reassemble the door frame and the door lever. English DV6800N_DC68-03650D-00_EN.indd 30 2018-01-31 12:43:14...
- Page 31 Move the location of the screws, used to fix the door hinge, as shown. 10. Remove the lever cover by pressing the hook on it. 11. Put the lever holder on the other side as shown. English 31 DV6800N_DC68-03650D-00_EN.indd 31 2018-01-31 12:43:14...
- Page 32 Installation 12. Insert and tighten the two hinge screws. 13. Insert and tighten the two screws on the opposite side of the door hinge. English DV6800N_DC68-03650D-00_EN.indd 32 2018-01-31 12:43:14...
-
Page 33: Before You Start
Before you start Here are a few things you should know before starting your dryer. Sort and load • Put one wash load in the dryer at a • Overloading reduces the tumbling time. action, resulting in uneven drying and •... -
Page 34: Operations
Operations WARNING To reduce the risk of fire, electric shock, or injury to persons, read the “Safety information“ before operating this appliance. Control panel Turn the cycle selector to select a desired cycle. When a cycle is 01 Cycle selector selected, the cycle indicator lights up. - Page 35 Press to change the temperature of the current cycle. • High: For sturdy cottons or those labeled Tumble Dry. • Medium: For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium. • Med Low: For heat lower than Medium. Use to dry synthetic or 04 Temp.
-
Page 36: Simple Steps To Start
Operations 12 Start/Pause Press and hold to start an operation, or press to stop an operation (Hold to Start) temporarily. NOTE Extremely tangled items finished by the washer may degrade the drying efficiency or cause the door to open. We recommend that you untangle the items before drying. Indicators Drying Child Lock... -
Page 37: Cycle Overview
Cycle overview Sensor Dry Sensor Dry cycles sense moisture in the load and stop the dryer when the load reaches the dryness level you have selected with Dry Level. Cycle Description NORMAL For most fabrics including cottons and linens. MIXED LOAD For mixed loads consisting of cotton and synthetic fabrics. -
Page 38: Cycle Guide
Operations Manual Dry You can change the drying settings manually to your preference. Cycle Description For drying light cotton synthetics or items that needs quick 30' EXPRESS drying. The default dry time is 30 minutes. TIME DRY You can specify a cycle time in minutes. AIR FLUFF Tumbles the load in room temperature air. - Page 39 Cycle Description Do not dry on a heat setting. Use AIR FLUFF. Foam Rubber (rug backs, stuffed toys, WARNING shoulder pads, etc.) Drying a rubber item with heat may damage it or cause a fire. Use NORMAL. • Add a couple of dry towels and a pair of clean sneakers to Pillows help the tumbling action and to fluff the pillows.
-
Page 40: Special Features
Operations Special features My Cycle Child Lock You can create your own cycle that Child Lock prevents children from playing contains your preferred settings and use it with the dryer. When Child Lock is at your convenience. activated, all buttons except for the Power button are disabled. - Page 41 To use Smart Care, you must have the • If you hold the smartphone at an angle Samsung Smart Care app installed on your to the dryer’s display, the smartphone smartphone. may not recognize the information NOTE code.
-
Page 42: Maintenance
Maintenance Keep the dryer clean to prevent decreased performance and to lengthen its life. WARNING The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - Do not contact these parts while the dryer is energized. Cleaning Control panel Stainless steel tumbler... -
Page 43: Troubleshooting
Troubleshooting Checkpoints If the dryer operates abnormally, first check the list of problems in the table below and try the suggested actions. Problem Action • Make sure the door is latched shut. • Make sure the power cord is plugged into a live electrical outlet. - Page 44 Troubleshooting Problem Action • Check the load for objects such as coins, loose buttons, nails, etc. Remove promptly. • Make sure the dryer is leveled properly as outlined in the Is noisy. installation instructions. • It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum, fan, or exhaust system.
- Page 45 Extended time. reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference. If a problem persists, contact a local Samsung service center. English 45 DV6800N_DC68-03650D-00_EN.indd 45 2018-01-31 12:43:17...
-
Page 46: Information Codes
• Check if a button is stuck. • If this information code remains, contact a Samsung service center. Incorrect door switch. • Contact a Samsung service center. If any information code keeps appearing on the screen, contact a Samsung service center. English DV6800N_DC68-03650D-00_EN.indd 46 2018-01-31 12:43:17... -
Page 47: Specifications
Specifications Fabric care chart Bleach The following symbols provide garment care direction. The clothing care labels Any bleach (when needed) include symbols for drying, bleaching, Only non-chlorine (color-safe) ironing, and dry cleaning. The use of bleach (when needed) symbols ensures consistency among garment manufacturers of domestic Tumble dry and imported items. -
Page 48: Protecting The Environment
Specifications Iron dry or steam temperatures Dry-clean High Dry-clean Medium Do not dry-clean Line dry / Hang to dry Drip dry Warning symbols for laundering Dry flat Do not wash Do not wring Do not bleach Do not tumble dry No steam (added to iron) Do not iron Protecting the environment... -
Page 49: Specification Sheet
Specification sheet Type Front loading dryer A. Height 33.5” (850 mm) B . Width 23.6” (600 mm) Dimensions C. Depth 25.8” (655 mm) D. Depth with door 44.2” (1123 mm) open 90° Net Weight 89.1 lb (40.4 kg) Heater rating 2200 W (elec.) English 49 DV6800N_DC68-03650D-00_EN.indd 49... -
Page 50: Cycle Chart
Specifications Cycle chart NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about ¾ full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about ½... -
Page 51: English
NOTE : factory setting, : can be selected • Temperature setting Time Cycle Extra High Medium Med Low setting NORMAL MIXED LOAD HEAVY DUTY JEANS SANITIZE Sensor Dry ACTIVE WEAR TOWELS PERM PRESS ... - Page 52 If service is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above.
- Page 53 God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book;...
- Page 54 Ridgefield Park, NJ 07660 1-800-SAMSUNG (726-7864) www.samsung.com/us/support Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty. Please contact your Samsung call agent for help with any of these issues. English DV6800N_DC68-03650D-00_EN.indd 54 2018-01-31 12:43:29...
- Page 55 If service is not available, SAMSUNG may elect to provide transportation of the product to and from an authorized service center. SAMSUNG will repair, replace, or refund this product at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above.
- Page 56 God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book;...
- Page 57 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) www.samsung.com/ca_fr/support (French) Visits by a Service Engineer to explain functions, maintenance or installation is not covered by warranty. Please contact your Samsung call agent for help with any of these issues. English 57 DV6800N_DC68-03650D-00_EN.indd 57 2018-01-31 12:43:29...
- Page 58 Memo DV6800N_DC68-03650D-00_EN.indd 58 2018-01-31 12:43:29...
- Page 59 Memo DV6800N_DC68-03650D-00_EN.indd 59 2018-01-31 12:43:29...
- Page 60 Scan this with your smartphone QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT 1-800-SAMSUNG (726-7864) U.S.A www.samsung.com/us/support 1-844-SAM-PAYS (726-7297) 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) CANADA 1-844-SAM-PAYS (726-7297) www.samsung.com/ca_fr/support (French) DC68-03650D-00 DV6800N_DC68-03650D-00_EN.indd 60 2018-01-31 12:43:29...