Yamaha 01X Software Installation Manual page 12

e Mode
This determines the particular driver operation, and should be set to match
the particular software used.
• ASIO ........................... All mLAN audio channels are set for ASIO.
The two latter channels are connected to the
monitor input of the 01X.
• WDM(2CH)+ASIO ...... This setting is intended for certain sequencers,
such as the SQ01. In this setting, mLAN audio
channels 15 and 16 (7and 8 when 01X is set to
96kHz/88.2kHz operation) (from computer to
01X) are set to WDM (for TWE), while the
remaining channels (also computer to 01X) are
set to ASIO (for the Audio Mixer). All mLAN
audio channels from the 01X to computer are
set to ASIO operation. The two latter ASIO
channels are connected to the monitor input of
the 01X.
• ........................... This setting is intended for certain sequencers,
WDM
such as SONAR, and sets all mLAN audio
channels to WDM operation. The two latter
channels are connected to the monitor input of
the 01X.
• When selecting "WDM + ASIO" or "WDM," confirm the settings in the Sounds
and Audio Devices Properties (page 13) after installing
r Status
This indicates the current data (MIDI/Audio) reception status (from 01X
to Computer) of the mLAN connection. If there is an error in
transmission, a message is shown.
Blue .........Data is being properly transmitted.
Yellow......Only one type of data (MIDI or audio) is being received.
Red ..........Error in reception.
Gray.........No reception.
About the Information window
This window indicates the data reception status (from the 01X to
computer) for both MIDI and audio.
R1, R2, etc.
This indicates the data reception status. "R1" cor-
responds to MIDI reception while "R2 corresponds
to audio reception from the 01X. The number of
tabs shown differs depending on your particular
computer configuration.
Receive Status
This mark indicates the order in which the data of each format is
received. The symbol "o" indicates that data in the corresponding
format is being received. The symbol "-" indicates that data in a
different format is being received. For example, the symbol
"oooooooo-" in the "Audio" field indicates that nine sequences
have been received, and the first eight sequences are in the
audio data format. The "Unknown" field displays symbols if
sequences in unknown formats are received. These fields are
blank if no mLAN data is received. If an error occurs during
reception, a red warning message flashes. In this case, check
the transmission device.
Icon
Blue .........Reception is normal.
Red..........Error in reception.
Gray ........No reception.
12
TOOLS for 01X/Plug-in Effect Installation Guide
t Set
Clicking this button actually applies the settings made in this window.
Changes to the settings do not take effect unless [Set] is clicked.
y Revert
If you've made changes to the settings (but not yet clicked [Set]), clicking
this button restores the settings made the last time [Set] was clicked. Once
you click [Set], [Revert] cannot be used.
u EXIT
Click to close the dialog box.
When canceling the installation
If you've cancelled an installation before it is complete, the soft-
ware may not have been installed properly. Follow the instructions
below to properly install the software.
1
Click on "Add or Remove Programs" in the Control Panel (page
6) and find "Install mLAN for 01X" and "mLAN Tools 2.0" in the
list.
2
Delete the two programs in order: first, "Install mLAN for 01X,"
then "mLAN Tools 2.0."
3
Start installation again from step 12 (page 7).
When the settings of the mLAN Auto Connector or Driver
Setup cannot be changed, or when the program Install
mLAN for 01X/mLAN Tools 2.0 cannot be uninstalled.
The message below may sometimes appear when changing the
settings with mLAN Auto Connector and Driver Setup or when
uninstalling.
When using the mLAN driver with a program such as an audio
sequencer, the settings in mLAN Auto Connector and Driver
Setup cannot be changed, and Install mLAN for 01X/mLAN
Tools 2.0 cannot be uninstalled. Execute these operation only
after closing all applications.
There may be times when the settings in mLAN Auto Connec-
tor and Driver Setup cannot be changed and Install mLAN for
01X/mLAN Tools 2.0 cannot be uninstalled, even when appli-
cations are not running. This may occur in the following
cases.
• When Mode in the Driver Setup is set to "WDM" or "WDM +
ASIO."
• When the mLAN WDM driver ("mLAN Audio Out/In 01") is
selected as the audio device in Windows.
If this is the case, follow the instructions below before changing the
settings in mLAN Auto Connector and Driver Setup and/or unin-
stalling Install mLAN for 01X/mLAN Tools 2.0.
1
Select [Start] [Control Panel]
Devices] [Voice]. Make sure that something other than
"mLAN Audio Out/In 01" is selected for the "Voice playback"
and "Voice recording" settings.
2
Select [Start] [Control Panel]
Devices] [Audio]. Make sure that something other than
"mLAN Audio Out/In 01" is selected for the "Sound playback"
and "Sound recording" settings.
[Sounds and Audio
[Sounds and Audio