Page 1
Wired Controller Manual Mode Name: ADSA1 Thank you for choosing Pioneer International Air Conditioners, please read this owner’s manual carefully before operation and retain it for future reference. If you have lost the User's Manual,please contact the local agent or visit www.pioneerair.com.au...
Content User Instructions ....................1 Installation......................1 Installation Place and Installation Requirements...........1 Installation of the Signal Wire................1 Installation of Wired Controller................2 Display and Installation instruction ..............3 Liquid crystal display.....................3 Bottoms.........................5 Operation Instruction ..................6 Lock Function......................6 The Switch of Centigrade and Fahrenheit.............6 Defrost Function....................6 On/Off........................6 Mode Setting......................6...
User Instructions Please carefully read this manual before installation and use of this product. ● Do not install or remove the wired controller by yourself. If necessary, please contact the after- sales serviceman. ● Do not install the wired controller in the humid area or under direct sunlight. ●...
Installation 3. Installation of Wired Controller The simple installation step of wired controller is as shown on the figure, please notice below issues: ● Open the bottom plate of the wired controller. ● Pull out the 4 core twisted pair wire from the mounting hole and pass this line through the square hole located at the bottom plate of the wired controller.
Display and Installation instruction Liquid crystal display: 15 16 17 18 19 10 11 12 30 31 34 35 Icon Nam e Icon Ins truction Select the operating Mode mode:Auto,Cooling,Dehumidification,Fan,Heating Setting fan speed Setting operating temp., range:16-31°C (61°F-88°F) ︿ Setting timer time, range: 0.5-24 hour ﹀...
Page 6
Display and Installation instruction Icon Nam e Icon Ins truction Horizontal Sw ing Horizontal Sw ing function status Vertical Sw ing Vertical Sw ing function status (N/A) Sleep Sleep function status ECO function status Dry function status Health Health function status (N/A) Memory Memory function status Wifi...
Display and Installation instruction Icon Nam e Icon Ins truction W-outlet W-outlet status (N/A) E-Heater E-Heater function status Solar Sloar status (N/A) Lock Keyboard lock status Shield Shield status Timer Setting timer on/off Bottoms: Button Name Button Instruction Turn on/off unit Home...
Operation Instruction Lock Function In the on/off-state, press " " and " " buttons at the same time for 5s till the wired controller enters the lock state. In this case, the LED display " ". After that, repress these two buttons at the same time for 5s to quit the lock state. Notice: In the lock state, if malfunction occur, all the buttons will be shield besides Home button.
Operation Instruction Temperature Setting Press " " or " " button to increase or decrease setting temperature in on-state of the unit. If press either of them continuously, temperature will be changed rapidly. Temperature setting range is 16°C~31°C (61°F-88°F). Fan Speed Setting Press "...
Operation Instruction Timer Setting In on-state, press " " button for 3s to set turn off time; in off-state, press " " button for 3s to set turn on time. Timer range: 0.5-24h Notice: The min gap of time display is 0.5h, less than 0.5h will display 0.5h. ●...
Operation Instruction Turbo Function Setting In Cooling/Heating/Fan mode, press " "button for 3s to switch the Turbo function, In this case, the LED display " " and" ". After that, press " " button at the same time for 3s to quiet function. then press " "...
Operation Instruction Quiet Function Setting In Auto/Cooling/Dehumidification/Fan/Heating mode,press" "button for 3s to switch the Turbo function,After that press " "button at the same time for 3s to Quiet function ,In this case ,the LED display " "and " ".Then press " "button to turn off the function.
Page 13
Operation Instruction Press " " button to switch to Press " " / " " button to In Cooling/Dehumidification/ ECO limited temperature set cooling(heating) limited Heating mode setting function, " " and (" setting temperature "/" "/" ") icon blinking Press "...
Error Code When error happens to the unit, the error code will be shown on the wired controller. When multiple errors simultaneously happen, the error codes will circularly show up. When error occurs, please immediately shut down the unit and contact service center. ●...