Page 1
(DM シー トチェック方法) ....60/62 CIRCUIT DIAGRAM(回路図) SYSTEM BOOTING FLOWCHART (起動フローチャート) ....64/66 001909 HAMAMATSU, JAPAN Copyright (c) Yamaha Corporation. All rights reserved. PDF ’15.02...
Page 2
IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
Page 3
• 12 cm x 2 + 4 cm x 2 • 12 cm ×2 + 4 cm ×2 Power Supply 電源 • AC Adaptor PA-150 or an equivalent recommended by Yamaha • 電源アダプター:PA-150B またはヤマハ推奨の同等品 • Power Consumption: 6 W (When using PA-150 AC adaptor) • Auto Power Off Function •...
Page 4
• 12 cm x 2 Power Supply • 12cm ×2 電源 • AC Adaptor PA-150 or an equivalent recommended by Yamaha • 電源アダプター:PA-150B またはヤマハ推奨の同等品 • Power Consumption: 6 W (When using PA-150 adaptor) • 消費電力:6 W ( 電源アダプター PA-150B 使用時 ) •...
Page 5
P-115B/P-115WH/P-45B ■ PANEL LAYOUT(パネルレイアウト) P-115B/P-115WH Shows the jacks and terminals as seen when viewed from the rear of the instrument. 本体背面(後ろからみた図です) ] (Standby/On) switch ]( スタンバイ / オン ) スイッチ w [MASTER VOLUME] slider w [MASTER VOLUME] スライダー e [DEMO/SONG] button e [DEMO/SONG] ボタン...
Page 6
P-115B/P-115WH/P-45B P-45B Shows the jacks and terminals as seen when viewed from the rear of the instrument. 本体背面(後ろからみた図です) ] (Standby/On) switch ]( スタンバイ / オン ) スイッチ w [MASTER VOLUME] slider w [MASTER VOLUME] スライダー e [GRAND PIANO/FUNCTION] button e [GRAND PIANO/FUNCTION] ボタン...
Page 7
P-115B/P-115WH/P-45B ■ CIRCUIT BOARD LAYOUT(ユニットレイアウト) P-115B/P-115WH UPPER CASE ASSEMBLY (上ケース Ass y) <Bottom view> TWEETER L TWEETER R (ツイーター L ) (ツイーター R ) UPPER CASE ASSEMBLY (上ケース Ass y) <Bottom view> FFC GUIDE TW CABLE GUIDE R TW CABLE GUIDE L KEYBOARD ASSEMBLY (FFC ガイド)...
Page 8
P-115B/P-115WH/P-45B P-45B UPPER CASE ASSEMBLY (上ケース Ass y) <Bottom view> UPPER CASE ASSEMBLY (上ケース Ass y) <Bottom view> KEYBOARD ASSEMBLY FFC GUIDE (FFC ガイド) (鍵盤 Ass y) LOWER CASE ASSEMBLY <Top view> (下ケース Ass y) SPEAKER L SPEAKER R (スピーカー L)...
Page 9
P-115B/P-115WH DISASSEMBLY OF P-115B/P-115WH(P-115B/P-115WH の分解) A-1. Lower Case Assembly(下ケース Ass’ y) ............10 A-2. DM Circuit Board(DM シート)...
Page 10
P-115B/P-115WH/P-45B P-115B/P-115WH A.■ DISASSEMBLY■OF■P-115B/P-115WH P-115B/P-115WH の分解 A-1. 下ケース Ass’ y A-1.■ Lower■Case■Assembly■ (所要時間:約 10 分) (Time■required:■About■10■minutes) A-1-1. [S40]のネジ 58 本を外し、下ケース Ass’ y を外し A-1-1. Remove the fifty-eight (58) screws marked [S40]. The ます。 (図 A-1) (図 A-2) lower case assembly can then be removed. (Fig. A-1) (Fig. A-2) <Bottom view> [S40] [S40] [S40] [S40] [S40] [S40] [S40]...
Page 11
P-115B/P-115WH/P-45B P-115B/P-115WH A-2.■ DM■Circuit■Board A-2. DM シート (所要時間:約 11 分) A-2-1. 下ケース Ass’ y を外します。 (A-1 項参照) (Time■required:■About■11■minutes) A-2-2. [S10A]のネジ 4 本を外し、 DM シートを外します。 A-2-1. Remove the lower case assembly. (図 A-3) (See procedure A-1.) A-2-2. Remove the four (4) screws marked [S10A]. The DM circuit board can then be removed. (Fig. A-3) A-3.■ JK■Circuit■Board■(including■DC-IN) A-3. JK シート (DC-IN を含む) (所要時間:約 11 分)...
Page 12
P-115B/P-115WH/P-45B P-115B/P-115WH A-6.■ Keyboard■Assembly■ A-6. 鍵盤 Ass’ y (所要時間:約 13 分) (Time■required:■About■13■minutes) A-6-1. 下ケース Ass’ y を外します。 (A-1 項参照) A-6-1. Remove the lower case assembly. A-6-2. [S30B]のネジ 3 本を外し、 FFC ガイドを外します。 (See procedure A-1.) (図 A-4) A-6-2. Remove the three (3) screws marked [S30B], then A-6-3. [S30C]のネジ 2 本を外し、TW 束線ガイド L を外...
Page 13
P-115B/P-115WH/P-45B P-115B/P-115WH A-8.■ PN2■Circuit■Board■ A-8. PN2 シート (所要時間:約 14 分) (Time■required:■About■14■minutes) A-8-1. 下ケース Ass’ y を外します。 (A-1 項参照) A-8-1. Remove the lower case assembly. A-8-2. 鍵盤 Ass’ y を外します。 (A-6 項参照) (See procedure A-1.) A-8-3. [S10E] のネジ 10 本を外し、 PN2 シートを外します。 A-8-2. Remove the keyboard assembly. (See procedure A-6.) (図 A-6) A-8-3. Remove the ten (10) screws marked [S10E]. The PN2 circuit board can then be removed. (Fig. A-6)
Page 14
P-115B/P-115WH/P-45B P-115B/P-115WH When installing the TW assembly, make sure that the ※ TW Ass’ y を取り付ける際、TW ブラケットの爪(2 箇所) claws of the TW bracket (at 2 locations) go under the を上ケースの下に潜り込ませて取り付けてください。 upper case. (Fig. A-8) (図 A-8) UPPER CASE (上ケース ) TW ASSEMBLY L CLAWS (TW BRACKET) (TW Ass y L) (爪 (TW ブラケット) ) Fig.■A-8(図 A-8) A-10.■Speaker■Grille■ A-10. SP グリル (所要時間:約 14 分) (Time■required:■About■14■minutes) A-10-1. 下ケース Ass’ y を外します。 (A-1 項参照)...
Page 15
P-115B/P-115WH/P-45B P-45B B.■ DISASSEMBLY■OF■P-45B P-45B の分解 B-1. 下ケース Ass’ y B-1.■ Lower■Case■Assembly■ (所要時間:約 10 分) (Time■required:■About■10■minutes) B-1-1. [S40]のネジ 58 本を外し、下ケース Ass’ y を外し B-1-1. Remove the fifty-eight (58) screws marked [S40]. The ます。 (図 B-1) (図 B-2) lower case assembly can then be removed. (Fig. B-1) (Fig. B-2) B-2. DM シート (所要時間:約 11 分) B-2.■ DM■Circuit■Board■ B-2-1. 下ケース Ass’ y を外します。 (B-1 項参照)...
Page 16
P-115B/P-115WH/P-45B P-45B B-3.■ JK■Circuit■Board■(including■DC-IN)■ B-3. JK シート (DC-IN を含む) (所要時間:約 11 分) (Time■required:■About■11■minutes) B-3-1. 下ケース Ass’ y を外します。 (B-1 項参照) B-3-1. Remove the lower case assembly. B-3-2. [S10B] のネジ 9 本を外し、 JK シート (DC-IN を含む) (See procedure B-1.) を外します。 (図 B-3) B-3-2. Remove the nine (9) screws marked [S10B]. The JK circuit board (including DC-IN) can then be removed. (Fig. B-3) B-4.■ Speaker■...
Page 17
P-115B/P-115WH/P-45B P-45B B-6.■ PN■Circuit■Board■ B-6. PN シート (所要時間:約 14 分) (Time■required:■About■14■minutes) B-6-1. コントロールパネル面から、スライドツマミを紐 B-6-1. Tie a string or the like to the slide knob and pull the 状のものでひっかけるようにして外します。 string to remove the slide knob from the control panel (図 B-5) side. (Fig. B-5) B-6-2. 下ケース Ass’ y を外します。 (B-1 項参照) B-6-2. Remove the lower case assembly. B-6-3. 鍵盤 Ass’ y を外します。 (B-5 項参照) (See procedure B-1.) B-6-4. [S10C]のネジ 8 本を外し、PN シートを外します。...
Page 18
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B C.■ Disassembling■the■Keyboard■Assembly 鍵盤 Ass’ y の分解 C-1. 白鍵 Ass’ y、黒鍵 Ass’ y White■key■assembly■and■black■key■assembly C-1. 各オクターブ(C ~ B)の白鍵 Ass’ y と黒鍵 Ass’ y Remove the four (4) screws marked [270A] fixing the を 止 め て い る[270A] の ネ ジ 4 本 を 外 し、 白 鍵...
Page 19
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B C-5. C-5. Rubber■Contact 接点ゴム Remove the black and white key assembly for two 該当する接点ゴムの 2 オクターブ分の白鍵 Ass’ y /黒鍵 Ass’ y を外して、接点ゴムを外します。 octaves related to the subject rubber contact. The rubber (図 C-4、図 C-5) contact can then be removed. (Fig. C-4, Fig. C-5) Note that the rubber contact has a specific installation ※ 接点ゴムには、向きがあります。 direction. 接点ゴムは、C# ~ C の一連です。 (キーは C ~ B) One rubber contact fits for C# – C (for C – B keys). <Top view>...
Page 20
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B C-6. C-6. GHL88L■Circuit■Board GHL88L シート Remove the black and white key assembly (A-1 – B2). A-1 ~ B2 までの白鍵 Ass’ y /黒鍵 Ass’ y を外しま す。 (C-1 項参照) (See procedure C-1) [260A]のネジ 6 本を外して、GHL88L シートを外 Remove the six (6) screws marked [260A]. The します。 (図 C-4) GHL88L circuit board can then be removed. (Fig. C-4) C-7.
Page 21
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B Hammer■(White■Key),■(Black■Key) C-9. ハンマー(白鍵) 、 (黒鍵) C-9. 該当する白鍵 Ass’ y /黒鍵 Ass’ y を外します。 Remove the black and white key assembly for the related keys. 鍵盤フレームを裏側にして、後方からハンマーを With the key frame placed upside down, push the 前に押すと、 「カチッ」と音がして鍵盤フレーム のハンマー軸からハンマーの軸受け部が外れます。 hammer forward from the rear, then a click sound is ハンマーを横にして取り出します。 heard and the hammer bearing section can be removed from the hammer axis of the key frame. Take out the (図 C-7、図 C-8) hammer sideways. (Fig. C-7, Fig. C-8) ※...
Page 22
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B D.■ Assembling■the■Keyboard■Assembly 鍵盤 Ass’ y の組立 D-1. ハンマー(白鍵) 、 (黒鍵) Hammer■(White■Key),■(Black■Key) D-1. ハンマー軸部にグリス塗布後、後方からハンマー After applying grease to the bearing section of the (白鍵) 、 (黒鍵)を横にして入れて、ハンマーの軸 hammer, bring the hammer (white key) (black key) 受け部を鍵盤フレームのハンマー軸にはめ込み、 sideways from the rear, fit its bearing section to the 「カチッ」と音がするまでハンマーを手前に引いて...
Page 23
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B D-4. D-4. GHL88H■Circuit■Board GHL88H シート GHL88H シートを取り付け、 [260C]のネジ 5 本で Tighten the five (5) screws marked [260C] to fix the 固定します。 (図 C-4) GHL88H circuit board. (Fig. C-4) D-5. Rubber■Contact 接点ゴム D-5. 接点ゴムには、取り付けの向きが決まっています。 Note that the rubber contact has specific installation 接点ゴムを逆に取り付けないように注意してくだ direction. Be careful not to install it in the wrong さい。 direction. ※ 接点ゴムの三角マーク(△)がフロント側になることを * A triangle mark (△) on the rubber contact must face the front. (Fig. D-2)
Page 24
P-115B/P-115WH/P-45B P-115B/P-115WH P-45B D-7. White■key■assembly■and■black■key■assembly 白鍵 Ass’ y、黒鍵 Ass’ y D-7. キ ー ガ イ ド に グ リ ス 塗 布 後、 白 鍵 Ass’ y / 黒 鍵 After applying grease to the key guide, install the white Ass’ y を取り付けます。このとき、鍵盤フレームの key assembly/black key assembly. At this time, check キーガイドと白鍵前部の内側スリット、ハンマー to make sure that the key guide of the key frame and の接点アームと白鍵 Ass’ y /黒鍵 Ass’ y の駆動ラ...
P-115B/P-115WH/P-45B P-115B/P-115WH DM■Circuit■Board ● ● to JK-CN4 to PN2-CN7 to GHL88M-CN2 to SPEAKER L to SPEAKER R (SP & TW) (SP & TW) Component■side(部品側) Pattern■side(パターン側) 2NA-ZN32050...
Page 27
P-115B/P-115WH/P-45B P-115B/P-115WH JK■Circuit■Board ● ● Component■side(部品側) to DM-CN6 to DM-CN4 2NA-ZN32660...
Page 28
P-115B/P-115WH/P-45B P-115B/P-115WH PN1■Circuit■Board ● ● Panel printing (パネル印刷) The panel printing and the triangle ( △ ) mark are not matched but the operation is matched with the panel printing. (パネル印刷と△印が相違してい ますが、動作はパネル印刷と合致 しています。 ) Component■side(部品側) 2NA-ZN32660...
P-115B/P-115WH/P-45B P-45B DM■Circuit■Board ● ● to PN-CN401 to GHL88M-CN2 to SPEAKER L to SPEAKER R Component■side(部品側) Pattern■side(パターン側) 2NA-ZM44770...
Page 32
P-115B/P-115WH/P-45B P-45B JK■Circuit■Board ● ● Component■side(部品側) to DM-CN104 to DM-CN103 to DM-CN105 2NA-ZN44760...
Page 40
Unless otherwise specified, take measurement at the PHONES terminal. (Use a stereo plug.) PHONES : Install a measuring plug (L/R ch: 33-ohms load) Install a measuring plug to one side only. (P-115B/P-115WH) AUX OUT : Install a measuring plug (L/R ch: 10k-ohms load) PEDAL UNIT : Connect the pedal unit (LP-5A/LP-5AWH).
Page 41
Test items are listed in Table 1. Press the corresponding key to select and execute each test. (See Fig. 2) To enter the test item select mode after completing each test item, press the lowest key or the [DEMO/SONG] button (P-115B/ P-115WH only).
Page 42
P-115B/P-115WH/P-45B 5.■ Test■items■(Table■1) * The “–” mark in the table means “Not applied”. P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key Version To check the Main Program version using C0 – A2 keys. <Main Program> Keys C0 – A0: To check the integer section Keys C1 –...
Page 43
P-115B/P-115WH/P-45B P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key – – D#1 Memory check Executes the simplified check of the Master ROM, RAM, Wave ROM and Effect RAM 1 all connected to the CPU bus. 1) Press the [D#1] key, and testing is executed.
Page 44
P-115B/P-115WH/P-45B P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key Output level R Measures the signal output level of the signal output from the R channel of each output check terminal. 1) Connect the level meter to the output terminal to be measured.
Page 45
4) When the plug is disconnected, P-115B/P-115WH: the C4 sine wave sound production is stopped. P-45B: the C4 sine wave sound is produced through the speaker for 1 second. For the NG test result, the C4 sine wave ound is produced (continuously until any key is pressed).
Page 46
P-115B/P-115WH/P-45B P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key SW check Checks whether each panel button with its LED (if available) works properly or not. P-115B/P-115WH 1) Press the [C#3] key of the keyboard. 2) Press switches one at a time in the order specified below.
Page 47
P-115B/P-115WH/P-45B P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key – – Lighting of all Checks whether all the LED lamps light properly or not. panel LEDs 1) Press the [C3] key. 2) Confirm that all LED lamps light. 3) Press the lowest key to exit the TEST item, and LED lamps are turned off.
Page 48
P-115B/P-115WH/P-45B P-45B P-115B/P-115WH Test■item Test■function■and■judgment■criteria No. Key No. Key Pedal 4 check Checks whether the Sustain Pedal (Pedal 4) works properly or not. (Sustain) 1) Connect the Sustain Pedal (Foot switch FC4) to the [SUSTAIN] terminal before turning on the power.
Page 49
Turn the master volume to the maximum position. Mesure the output voltage and confirm that the measured value meets the following. <PHONES> L: -90.0 dBu or less R: -90.0 dBu or less <AUX OUT> (P-115B/P-115WH only) L: -90.0 dBu or less R: -90.0 dBu oe less...
Page 60
P-115B/P-115WH/P-45B ■ ■ DM■CIRCUIT■BOARD■CHECK■METHOD P-115B/P-115WH The DM Circuit Board is provided with test points for service check purposes. Check the test points on the DM Circuit Board if the following symptoms appear. Symptoms■and■check■items No Pilot lamp with Power SW ON --> Check items q to t sequentially.
Page 61
P-115B/P-115WH/P-45B P-45B The DM Circuit Board is provided with test points for service check purposes. Check the test points on the DM Circuit Board if the following symptoms appear. Symptoms■and■check■items No Pilot lamp with Power SW ON --> Check items q to r sequentially.
Page 64
P-115B/P-115WH/P-45B ■ ■ SYSTEM■BOOTING■FLOWCHART P-115B/P-115WH Power On Port initial setting SPOFF = H (IC1, T2) Starts accessing to IC18 MUTE = H (IC1, T3) CPU, each registers ERR-DETECT = If not, IC1 may be L (IC1,AB19) defective Pulse is output from...
Page 65
P-115B/P-115WH/P-45B P-45B Power ON 150pin (PB0) L → H Boot Main Starts initialization task Cancels DAC-IC Reset 138pin (PB1) L → H With backup ROM PCM initialization Backup data initialized Cancels interrupt mask Completes initialization task After 100 msec. If it boots but does not run up to here, the PROGRAM ROM (IC105) usually is not the problem.
Page 66
P-115B/P-115WH/P-45B ■ ■ 起動フローチャート P-115B/P-115WH Power On ポート初期設定 IC18 へのアクセスが SPOFF = H (IC1、 T2) 始まる MUTE = H (IC1、 T3) 各種レジスタ設定 ERR-DETECT = IC18 へのアクセスが始ま L ( IC1、 AB19) らない場合は、 IC1 が不良 の可能性 ERR-DETECT IC8 へのアクセスが BOOT 用 (IC1、 AB19) 始まる SDRAM 初期化 からパルスが出力される 0 クリア、 定数設定...
Page 67
P-115B/P-115WH/P-45B P-45B Power ON 150pin (PB0) L → H Boot Main 初期化タスク起動 DAC-IC Reset解除 138pin (PB1) L → H バックアップROM有り PCMの初期化 バックアップデータの初期 割り込みマスク解除 初期化タスク終了 100 msec後 Bootは通るが、ここまで動作しない場合、 ProgRom (IC105)は問題ない。 SWX03 (IC100)の不良。 テストモード ? テストモード起動 (A3 正弦波出力) バックアップROM無し バックアップデータの初期化 テストに入れない場合、鍵盤の不良 PAD/MIDIで音を鳴らすことが可能 テストプログラム 通常動作...
Page 68
P-115B/P-115WH/P-45B ■ ■ DATA■BACKUP■AND■INITIALIZING(バックアップと初期化) P-115B/P-115WH 以下の設定やデータは自動的にバックアップされるので、電 The following data will automatically be maintained as back- 源を切っても消えません。 up data even if you turn off the power. バックアップデータ Backup■data Metronome/Rhythm Volume, Metronome/Rhythm se- メ トロノーム / リズム音量、 メ トロノーム / リズム設定 ( 拍...
Page 69
P-115B/P-115WH/P-45B P-45B 以下の設定やデータは自動的にバックアップされるので、電 The following data will automatically be maintained as back- 源を切っても消えません。 up data even if you turn off the power. バックアップデータ Backup■data Metronome Volume, Metronome Beat, Touch Sensitiv- オートパワーオフ機能、チューニング 、タッチ感度、鍵 盤操作音オン/ オフ、メ トロノームの音量 / 拍子の設定 ity, Tuning, Auto Power Off, Operation Confirmation Sound on/off バックアップデータを初期化する...
Page 70
End all the application software. Exit from any power-saving mode of the computer (such as suspended, sleep, standby). Connect the P-115B/P-115WH to the PC with an USB cable. Turn on the power of P-115B/P-115WH. Click the Control Panel on PC.
Page 98
P-115B/P-115WH/P-45B Note : See parts list for details of circuit board conponent parts. 注:シートの部品詳細は、パーツリストをご参照ください。 ■ WARNING Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed. ■ 安全上の注意 印の部品は、安全を維持するために重要な部品です。 交換する場合は、安全のために必ず指定の部品をご使用ください。...
Page 99
■ BLOCK DIAGRAM(ブロックダイアグラム)(P-115B/P-115WH) P-115B/P-115WH/P-45B P-115B/P-115WH MASTER VR JK 1/2 JK 2/2 ※ and CN1 are shown separately here but actually they A10k SW MATRIX STANDBY/ON SW MATRIX constitute one circuit board. LD3–5 SW7–15 LD1–2 SW2–6 JK 1/2 JK 2/2 ※ 、 及び CN1 は分割して記載していますが、1 枚のシートです。 POWSW CN7 (22P)
Page 100
■ BLOCK DIAGRAM(ブロックダイアグラム)(P-45B) P-115B/P-115WH/P-45B Keyboad GHL88H C#5 – C7 CN1 (17P) 88Keys GRAND PIANO/ MASTER VR STANDBY/ON FUNCTION AC ADAPTOR A10k CN3 (17P) PA-150/PA-150A /PA-150B/PA-5D GHL88L VR401 GHL88M LD401 SW402 SW401 A-1 – C2 DC IN (12V) C#2 – C5 CN2 (27P) +3.3D...
Page 101
■ WIRING DIAGRM(基板結線図) P-115B/P-115WH/P-45B P-115B/P-115WH P-45B SP L channel SP R channel SP L channel SP R channel CN401 DC-IN CN201 DC-IN CN102 CN201 CN4 CN7 CN301 CN103 CN301 CN302 CN103 GHL88H GHL88M GHL88L GHL88H GHL88M GHL88L Unit Name Location Source Destination...
Page 102
■ DM 001 CIRCUIT DIAGRM (P-115B/P-115WH) P-115B/P-115WH/P-45B P-115B/P-115WH SWX08 VOLTAGE DETECTOR INVERTER SWX08 WORK SDRAM 128M FLASH ROM 64M PROGRAM SWX08 SWX08 not installed not installed not installed SWX08 WAVE ROM 128M not installed not installed MKS5 DSP SDRAM 64M not installed not installed...
Page 103
■ DM 002 CIRCUIT DIAGRM (P-115B/P-115WH) P-115B/P-115WH/P-45B P-115B/P-115WH AMPLIFIER to PN2-CN7 (Page 8: H-4) SWX08 OP AMP not installed not installed not installed DIGITAL POWER AMPLIFIER SWX08 to SPEAKER L not installed to SPEAKER R not installed REGULATOR +3.3V SINGLE SHOT REGULATOR +1.2V not installed...
Page 104
■ PNJK (HP, JK, PN1, PN2) CIRCUIT DIAGRAM (P-115B/P-115WH) P-115B/P-115WH/P-45B P-115B/P-115WH PLAY VOICE STANDBY/ON PIANIST STYLE STRINGS MELLOW GP STAGE EP JAZZ ORG. ROCK ORG. W.BASS /HARPSI. /DX E.PIANO /VINTAGE EP /PIPE ORG. /VIB /E.BASS G.PIANO /BRIGHT GP to DM-CN7 (Page 7: Q-2) PHONES not installed not installed...
Page 107
■ GHL88M CIRCUIT DIAGRAM (P-115B/P-115WH/P-45B) P-115B/P-115WH/P-45B P-115B/P-115WH P-45B GHL88M to GHL88L-CN1 to GHL88H-CN1 (Page 10: B-7) (Page 9: M-8) to DM-CN1 (Page 6: U-16) P-115B/P-115WH P-45B to DM-CN201 (Page 12: K-1) 28CC1-2000006193 ■ GHL88M CIRCUIT DIAGRAM (P-115B/P-115WH/P-45B)
Page 108
■ DM CIRCUIT DIAGRAM (P-45B) P-115B/P-115WH/P-45B P-45B to GHL88M-CN2 (Page 11: O-10) REGULATOR +3.3V (DCDC) not installed to PN-CN401 (Page 13: C-4) to JK-CN103 SYSTEM RESET (Page 13: H-6) AND GATE SINGLE SHOT not installed not installed FLASH ROM 64M PROGRAM/WAVE to JK-CN301...
Page 109
■ PNJK (JK, PN) CIRCUIT DIAGRAM (P-45B) P-115B/P-115WH/P-45B P-45B not installed not installed to DM-CN103 (Page 12: A-4) STANDBY/ON GRAND PIANO/ FUNCTION not installed MASTER VOLUME WARNING not installed Components having special characteristics are marked and must be not installed to DM-CN104 replaced with parts having specification equal to those originally installed. (Page 12: A-3) DC IN (12V) 印の部品は、安全を維持するために重要な部品です。...