Knob Edit - Yamaha AN1x Owner's Manual

Knob Edit

The eight CO N TRO L k nobs let you edit va rious
cha ra cteristics of ea ch voice in rea l-time. Edited
da ta of the selected voice ca n be stored to a ny
voice m em ory (1 ~ 1 2 8 ).
The functio n o f each kno b depends o n which KN O B
PARAMETER G RO UP switch is selected. Available
parameter g ro ups are as fo llo ws:
SYN C/ FM :
Sync functio n/ Frequency Mo dulatio n
PEG/ LFO :
Pitch Envelo pe G enerato r/ L o w Frequency
O scillato r
VCO 1 :
Vo ltag e Co ntro lled O scillato r 1
VCO 2 : Vo ltag e Co ntro lled O scillato r 2
VCF:
Vo ltag e Co ntro lled Filter
M IX / VCF:
Mixer/ Vo ltag e Co ntro lled Filter
VCA: Vo ltag e Co ntro lled Amplifier
ASSIGN :
Assig ned kno b parameters
For more information about the CONTROL knobs, see page 2 6 .
A blank chart for writing down parameter values of user voices is provided on
page 1 1 4 .
1 . Press a KN O B PARAM ETER GRO UP sw itch.
The LED to the left of the selected sw itch
lights.
KNOB PARAMETER GROUP
SYNC/ FM
VCO1
VCF
VCA
The parameter available to co ntro l o r edit fo r each
kno b is printed o n the panel by each kno b, co lo r
co ded to match the related KN O B PARAMETER
G RO UP switch. Fo r example, if [VCA] (white switch) is
selected, each kno b accesses the parameter printed in
the white area to the lo wer left o f the kno b: Attack,
Decay, Sustain, Release, Feedback, Vo lume, Amo d
Depth, and Vel Sens, respectively.
Sync Pitch
Algorithm PEG Decay Sync Pitch PEG Depth PEG Sw
Depth
Wave Wave Pitch Pitch Fine Fine
VCO1 VCO2
Sustain
Attack Decay
Level Level
Attack Decay Sustain
ASSIGN 1 ASSIGN 2
ASSIGN 3
Sync
LFO1 Wave FM Depth LFO1 Spd FM Src1 LFO1 Dly
Pmod Sw
PW PW PWM Depth PWM Depth PWM Src PWM Src
VCF Reso VCF FEG Fmod
HPF
Depth Depth
Cutoff nance Type
Feedback Volume Amod Depth
ASSIGN 5 ASSIGN 6 ASSIGN 7
PEG/ LFO
VCO2
MIX/ VCF
ASSIGN
Sync Pitch
Port Time
Src
Edge Edge
KNOB PARAMETER GROUP
Ring Noise
Release
Mod Level
SYNC/ FM PEG/ LFO
Release
ASSIGN 4
VCO1 VCO2
FM Src2 LFO2 Spd
VCF
PmodDepth PmodDepth MIX / VCF
Vel Key
Sens Track
VCA ASSIGN
Vel Sens
ASSIGN 8
2 . Press a CO N TRO L k nob w ithout turning it.
The parameter name, current value and a ho rizo ntal
kno b data g raph will display in the L CD. A flashing
seg ment in the data g raph indicates the value po sitio n
o f the kno b, whereas shaded seg ments indicate the
actual current po sitio n o f the kno b.
Parameter name
Parameter value
Knob position of the
parameter value
(flashing segment)
3 . Turn the k nob one w a y or the other to edit
the va lue of the pa ra m eter.
T urning the kno b to the rig ht increases the value and
turning it to the left decreases the value.
The kno b data g raph pro vides a visual reference o f the
current kno b po sitio n as yo u turn the kno b. L eftward
po sitio ns are indicated by a sho rter ho rizo ntal bar, and
rig htward po sitio ns are indicated by a lo ng er bar.
Length of graph indicates
current knob position
You can omit step 2 and edit the parameter directly by turning the knob. Edit
information will display in the LCD accordingly.
Simply turning a knob will increase or decrease the parameter value in coarse
values ( large amounts) , and will cancel the flashing indicator. Turning a knob
while pressing it will increase or decrease the parameter value in fine values
( small amounts) , and will position the flashing indicator, which will remain
flashing when you subsequently release the knob. The range will be narrower
than that available by coarse edit.
4 . Edit other pa ra meters.
T o co nfirm and edit o ther parameters in the same
g ro up, simply repeat steps 2 and 3 . T o edit parameters
in o ther g ro ups, repeat steps 1 thro ug h 3 .
All the changes made here take place in the selected Scene.
53
Data graph
Actual knob position