Page 1
SERVICE MANUAL E Model Australian Model Ver. 1.3 2009.11 Canadian Model • TA-KMSW500 is the amplifi er section in HT-DDW5500/DDW7500/DDW8500. SPECIFICATIONS • Power amplifier (TA-KMSW500) Measured under the following conditions: RMS output (6 ohms, 80 Hz, THD 10%) Area code...
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TA-KMSW500 SECTION 1 This section is extracted from instruction manual. GENERAL LOCATION OF CONTROLS Front Panel VOLUME ILLUMINATION SUBWOOFER Turn to adjust the volume VOLUME level of the subwoofers. ILLUMINATION The illumination is on (initial setting). The illumination is off.
TA-KMSW500 SECTION 2 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 2-1. CASE (Page 4) 2-2. BACK PANEL SECTION (Page 5) 2-3. FRONT PANEL SECTION (Page 5) 2-4. CHASSIS SECTION (Page 6) Note: Follow the disassembly procedure in the numerical order given.
TA-KMSW500 2-4. MAIN BOARD SECTION CNP801 (7P) CNP902 (2P) one screw (+BVTP 3 x 8) two screws (+BVTP 3 x 8) two screws (+BVTP 3 x 8) MAIN board section...
TA-KMSW500 SECTION 3 DIAGRAMS 3-1. BLOCK DIAGRAM TB401 IC203 IC400 PRE DRIVER SPEAKERS CURRENT SUBWOOFER IC202 +VOUT1 POWER AMP DETECT 6 IN1 J201 Q704 Q701 - Q703, RY401 Q705 -VOUT1 SUBWOOFER AUDIO IN VOLUME RELAY CONTROL CURRENT DRIVER +VOUT2 POWER AMP...
Page 8
TA-KMSW500 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: Note: • X : Parts extracted from the component side.
TA-KMSW500 Ver. 1.2 3-4. PRINTED WIRING BOARD – LED RIGHT, LED LEFT, VOLUME CONTROL Section – • See page 14 for Circuit Boards Location. • : Uses unleaded solder. LED RIGHT BOARD MAIN BOARD CNP651 (Page 9) R103 CL105 R102...
TA-KMSW500 SECTION 4 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so they may • Items marked “*” are not stocked since The components identifi ed by have some difference from the original one. they are seldom required for routine ser- mark 0 or dotted line with mark •...
TA-KMSW500 4-2. FRONT PANEL SECTION not supplied (LEFT LED board) not supplied (VOL CONTROL SUPPORT board) not supplied (VOLUME CONTROL board) not supplied (RIGHT LED board) not supplied supplied with RV001 Ref. No. Part No. Description Remark Ref. No. Part No.
TA-KMSW500 Ver. 1.2 4-3. BACK PANEL SECTION not supplied The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specifi ed. Ref. No. Part No. Description Remark Ref. No.
TA-KMSW500 Ver. 1.2 4-4. CHASSIS SECTION F902 F903 F901 Q755 Q753 Q705 Q703 T901 not supplied not supplied The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specifi ed.
TA-KMSW500 Ver. 1.2 SECTION 5 ELECTRICAL PARTS LIST LEFT LED MAIN Note: • Due to standardization, replacements in • RESISTORS • Abbreviation the parts list may be different from the All resistors are in ohms. : Argentina model parts specifi ed in the diagrams or the com- METAL: Metal-fi...
Page 24
TA-KMSW500 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2009.04 2009.05...