Page 1 Tecra 8000 Series User’s Guide If you need assistance www.pcsupport.toshiba.com ❖ InTouch ❖ Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see Chapter 7 on page 108 in this guide.
Page 2 : Only peripherals complying with the FCC Class B limits may be attached to this computer. Operation with non-compliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's serial port, parallel port, monitor port, external disk drive port, USB port, PS/2™...
Page 3: Type Of Service
Contact: Toshiba America information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 FCC Requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems. Installation When you are ready to install or use the modem, call your local telephone company and give them the following information: ❖...
Page 4: If Problems Arise
FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation or an authorized representative of Toshiba Corporation. Disconnection If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Page 5: Industry Canada Requirement
The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Page 6 CD-ROM/DVD-ROM Safety Instruction The CD-ROM/DVD ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Page 7 Copyright This guide is copyrighted by Toshiba Corporation with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 8: Energy Star Compliance
Digital” are registered trademarks of Dolby Laboratories. All other brand and product names are trademarks or registered trademarks of their respective companies. Energy Star Compliance As an Energy Star partner, Toshiba has determined that this product is Energy Star Compliant.
Page 9: Table Of Contents
Contents Part I: Getting to Know Your Computer Chapter 1: To Begin... 1 Making sure you have everything... 1 Selecting a place to work... 1 Keeping the computer comfortable... 2 Keeping yourself comfortable... 3 Finding where everything’s located... 6 Front with the display panel closed... 6 Left side...
Page 10 Registering your computer... 17 When and how to turn off the computer... 17 Chapter 2: Using Your Computer in the Office... 21 Using external display devices... 21 Connecting the display device... 22 Directing the display output when you turn on the computer...
Page 11 Determining your COM port... 47 Using the computer’s telephony features... 48 Using the Internet... 48 Using bulletin board services... 49 Discovering Toshiba’s online resources... 49 Recording sounds with a microphone... 50 Using an external microphone... 50 Using an external audio input device ... 51 Using external speakers or headphones...
Page 12 Starting where you left off... 90 Changing batteries... 91 Taking care of your battery... 93 Safety precautions... 94 Maximizing battery life... 94 Disposing of used batteries safely ... 94 Conserving power... 95 The easy way—choosing a power usage mode in Windows 95 and Windows 98...
Page 13 DVD-ROM error messages... 141 Developing good computing habits ... 142 If you need further assistance... 143 Contacting Toshiba... 143 Toshiba's worldwide offices... 145 Part II: Technical Reference Chapter 8: System Setup ... 153 Using TSETUP... 153 Using Hardware Setup... 154 Using Hardware Setup in Windows 95/98...
Page 14 Instant password... 179 Disabling a user-level password... 180 Using a hard disk drive password... 180 Using an Eject Password... 184 Chapter 10: Managing Your Tecra 8000 Series Computer. 187 Industry standard architecture... 187 Wired for Management... 188 Desktop Management Interface... 188 Advanced Configuration and Power Interface...
Page 15 HDD supervisor level password... 198 Eject password... 198 Dock prevention lock... 198 Cable connection... 199 Part III: Appendixes Appendix A: Features and Specifications... 203 Appendix B: Power Cable Connectors... 217 Appendix C: System Resources... 219 Appendix D: Video Modes ... 227 Glossary...
Page 16 The documents included with this product ..... . xviii Safety cautions ..........xviii Other documentation .
Page 17 The Tecra 8000 Series notebook’s modular design also lets you add, change, or update additional components at any time, making this machine one of the most flexible tools you’ve ever owned.
Page 18: The Documents Included With This Product
xviii The documents included with this product This product comes with a user’s guide in printed form and a user’s guide in electronic form on your Configuration Builder CD. The “electronic book” lets you keep your guide with you wherever you and your computer go.
Page 19: Other Icons Used
WARNING: This icon indicates the existence of a hazard that could result in bodily injury if the safety instruction is not observed. CAUTION: This icon indicates the existence of a hazard that could result in damage to equipment or property if the safety instruction is not observed.
Page 20: Other Documentation
Configuration Builder CD to help you manage your system. Service options Toshiba offers a full line of service options built around its SelectServ™ warranty programs. See the warranty and service material included with your computer for registration information.
Page 23 ETTING TO OMPUTER What’s in Part I This part explains what all the computer’s components are and how to use them. Don’t hesitate to skip around. Guides, such as this one, don’t need to be read from cover to cover.
Page 24 Chapter Making sure you have everything ....... . 1 Selecting a place to work ........1 Finding where everything’s located .
Page 25: Chapter 1: To Begin
If any items are missing or damaged, notify your network administrator. Selecting a place to work Your Tecra 8000 Series computer is portable, designed to be used in a variety of circumstances and locations. However, by giving some thought to your work environment, you can protect the...
Page 26: Keeping The Computer Comfortable
To Begin Selecting a place to work Keeping the computer comfortable Place the computer on a flat surface that is large enough for the computer and any other items you need to use, such as a printer. Leave enough space around the computer and other equipment to give adequate ventilation;...
Page 27: Keeping Yourself Comfortable
Keeping yourself comfortable WARNING: Using the computer keyboard incorrectly can result in discomfort and possible injury. If your hands, wrists, and/or arms hurt while typing, stop using the computer and rest. If the discomfort persists, consult a physician. This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive- motion injury, and repetitive-stress syndrome.
Page 28 To Begin Selecting a place to work chair. Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. Below eye level Footrest Correct posture and positioning of the computer Position your chair so that the keyboard is at or slightly below ❖...
Page 29: Work Habits
Position the display panel or external monitor so that sunlight ❖ or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare. Avoid placing your computer in front of a bright light that ❖...
Page 30: Finding Where Everything's Located
To Begin Finding where everything’s located Finding where everything’s located The next few pages take you on a guided tour of the computer and its components. Front with the display panel closed Battery module Moving the battery release panel to the left and pulling the battery module forward when the battery lock is in the unlocked position allows you to remove the main battery module from the computer.
Page 31: Left Side
The CD-ROM ejection button opens up the CD-ROM tray and allows you to remove a CD. The SelectBay For more details, see “Swapping SelectBay modules” on page 37. Left side CPU fan USB port The CPU fan provides extra cooling when necessary to keep the computer’s Pentium processor continue performing at its maximum speed.
Page 32: Back
To Begin Finding where everything’s located The power button cover protects the power button. Slide this cover toward the front of the computer to reveal the power button. For more information, see “Turning on the computer” on page 15. The hard disk drive (HDD) cover protects the computer’s removable hard disk.
Page 33 Finding where everything’s located The 3.5 mm headphone jack lets you connect stereo headphones or other audio output devices. Connecting headphones or other devices to this jack automatically disables the internal speakers. The 3.5 mm line-in jack lets you connect an external stereo device for audio input.
Page 34: Right Side
SelectBay. The SelectBay ejection bar ejects the SelectBay module from the computer. The SelectBay of the Tecra 8000 Series can contain one of several interchangeable devices, offering exceptional system flexibility. For more information on SelectBay modules, see “Swapping SelectBay modules”...
Page 35: Underside
Memory module The battery module enables the Tecra 8000 Series to be used when a standard wall socket is not available. For further information about using the battery, see “Power Management” on page 85. Keyboard and display features To view the front of the computer with the display panel open: Locate the display latch on the front of the computer.
Page 36: Front With The Display Panel Open
To Begin Keyboard and display features Front with the display panel open Screen Microphone AccuPoint Speaker AccuPoint buttons The computer’s screen is a liquid crystal display (LCD) that provides clear, sharp images. The built-in microphone lets you record sounds and speak through the telephone modem.
Page 37: Indicator Panels
The AC power light glows green when the computer is connected to an external power source. The power light glows green when the computer is on. It blinks orange when you turn off the computer using Toshiba’s Resume Mode, Windows 95 or Windows NT Suspend, or Windows 98 Standby command.
Page 38: Keyboard Indicator Panel
To Begin Keyboard and display features The SelectBay battery light indicates the state of a secondary battery in the SelectBay, if installed. The light glows orange when the battery is charging and green when the battery is fully charged. The hard disk drive light indicates that the hard disk is currently in use.
Page 39: Attaching Other Components
AC adapter before you turn it on. Similarly, you should attach your external components and devices to your Tecra 8000 Series computer before you turn it on. For more information about each device, see “Using Your Computer in the Office” on page 21.
Page 40 To Begin Turning on the computer Locate the power light on the system indicator panel. Slide the power button cover on the left side of the computer toward the front of the computer, revealing the power button. Opening the power button cover Press and hold the power button in—about one second—until the power light turns on (green).
Page 41: The Operating System
The appropriate Microsoft operating system documentation came with your Toshiba computer. Registering your computer Sending in your product registration card lets Toshiba keep you up to date with information about new products and upgrades. Registering your computer also extends your Toshiba warranty worldwide at no charge to you.
Page 42 To Begin When and how to turn off the computer In Windows 98, use either Shut Down or Standby command ❖ to turn off the computer. ❖ In Windows NT, use the Shut Down command. If you plan to leave the computer off for more than eight hours, use the Shut Down command.
Page 43 To Begin When and how to turn off the computer Part I: Getting to Know Your Computer...
Page 44 Chapter Using external display devices ........21 Using an external keyboard .
Page 45: Chapter 2: Using Your Computer In The Office
Computer in the mputer in the Office Your Tecra 8000 Series computer was designed to be easy to use when you travel. However, it’s so powerful you can use it as your main office computer. This chapter describes how to connect devices that can increase the capabilities of your machine.
Page 46: Connecting The Display Device
Using Your Computer in the Office Using external display devices A video display device, such as a video projection unit via the ❖ composite video out port or the S-video out port (only with MPEG2 option). An external SVGA monitor via the monitor port (standard). ❖...
Page 47: Selecting Video Cables
RCA cable. For the best video quality, always use a properly shielded cable. HINT: Toshiba recommends using a cable no longer than 20 feet (approximately six meters). Using a poor quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.
Page 48: Directing The Display Output When You Turn On The Computer
Using Your Computer in the Office Using external display devices Restart the computer. Connecting an external monitor You can easily attach an external monitor to your computer if you need a larger screen. To connect an external monitor: Turn off the computer. Connecting an external monitor Connect the monitor’s video cable to the monitor port on the back of the computer.
Page 49: Adjusting The Quality Of The External Display
This hot key cycles through the settings in the following order: ❖ Built-in display only ❖ Built-in display and external monitor simultaneously ❖ External monitor only ❖ Built-in display and TV (or other external video device) simultaneously ❖ TV (or other external video device) TECHNICAL NOTE: You can also change these settings using the NeoMagic tab of the Display Properties Box.
Page 50: Using An External Keyboard
Making your external keyboard emulate the Fn key An external keyboard doesn’t have the Tecra 8000 Series computer’s built-in keyboard. If you use the computer’s hot keys or have set up key combinations in Fn-esse®, you’ll probably miss these features when using an external keyboard.
Page 51: Using An External Mouse
Windows 95 and Windows 98 When you connect a PS/2-compatible mouse to the PS/2 mouse/ keyboard port, you may use the mouse, the AccuPoint or both. CAUTION: When connecting any PS/2 device, Toshiba recommends turning off your computer to prevent any possible hardware damage.
Page 52: Setting Up A Ps/2 Mouse To Work With The Accupoint In Windows Nt
To set the PS/2 mouse to work simultaneously with the AccuPoint: Click Start, select Programs, then select Toshiba Utilities. Click Hardware Setup, click the Hardware Options button and then select the Pointing Devices tab. Select the Simultaneous radio button and click OK.
Page 53 Network Dock Port Replicator ❖ For more information, see “Expansion capability” on page 212. These docking solutions may be purchased through the Toshiba Accessories Catalog. You can access the Toshiba Accessories Catalog on Toshiba’s Web site www.toshiba.com. Each docking station comes with its own user’s guide that explains how to connect and use it.
Page 54 Using the computer’s telephony features ......48 Discovering Toshiba’s online resources ......49 Recording sounds with a microphone .
Page 55: Chapter 3: Hardware Features
By installing extra memory now, you’ll be able to operate your computer at its maximum capacity from the start. Of course, you can always return to this section if you decide to add memory later. HINT: To purchase additional memory modules, see the Toshiba Accessories Catalog.
Page 56: Memory Module Sizes
Hardware Features Adding memory Memory module sizes Additional memory is easy to install. Memory modules come in the following sizes: 32 MB ❖ 64 MB ❖ ❖ 128 MB The computer has two memory expansion slots. The following table shows the possible memory configurations: Total Memory 32 MB 64 MB...
Page 57: Installing A Memory Module
Installing a memory module You install additional memory modules into the memory expansion slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. Preparing to install with Windows 95/Windows 98 Before you can install a memory module, you must first shut down the computer.
Page 58 Hardware Features Adding memory Select Shut down the computer, then click Yes. Windows NT Workstation 4.0 shuts down and automatically turns off the computer. Inserting the module Unplug the computer. CAUTION: Installing a memory module with the computer’s power on may damage the computer, the module, or both. Close the display panel and remove any cables you may have connected.
Page 59 Removing memory module cover CAUTION: Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer.
Page 60: Removing The Memory Module
Hardware Features Adding memory Replace the cover and the screws. CAUTION: Don’t touch the connector on the back end of the hard drive. Doing so could generate electrostatic shock and corrupt data. The computer has two memory expansion slots—Slot A and Slot B.
Page 61: Swapping Selectbay Modules
An optional secondary hard disk drive (HDD) ❖ HINT: Items from this list that didn’t ship with your computer may be purchased. See the Toshiba Accessories Catalog. Removing a module from the SelectBay Do the following to remove one of the modules: Turn off the power.
Page 62 Hardware Features Swapping SelectBay modules Unlatching the SelectBay Slide the SelectBay ejection bar towards the back of the computer. The SelectBay module pops out about one-quarter inch. Slide the module out toward the front of the computer. Sliding the module out Retain the weight saver for transporting the computer when no other module is installed in the SelectBay.
Page 63: Inserting A Module Into The Selectbay
Inserting a module into the SelectBay This section explains how to install the module and its cover into the SelectBay. Snap the module into the cover, if necessary. To install the external diskette drive, you must remove it from its external casing. To remove it, see “Inserting the external diskette drive”...
Page 64: Using The Secondary Battery In The Selectbay
Hardware Features Swapping SelectBay modules Releasing the drive module Once the external diskette drive is out of its case, it can be attached to the drive cover. Using the secondary battery in the SelectBay The optional secondary battery is shipped with an adapter that fits into the SelectBay.
Page 65 Battery release lever Snapping the battery into the adapter To place the battery into the adapter: Align the contacts on the battery with the contacts on the adapter. Push down to snap the battery into the adapter. Removing the battery from the adapter Removing the battery from the adapter Holding the battery adapter front toward you, slide the battery release latch to your right.
Page 66: Using Pc Card Slots
CAUTION: Your Tecra 8000 Series computer came with all the Card and Socket Services programs you need. Even if your PC Card comes with its own version of Card and Socket Services, you should use the files provided on your computer.
Page 67 Type III card takes up the space for both slots—you cannot have a Type III card installed with any other card. To insert a PC Card: NOTE: If your operating system is Windows NT, you must turn off the computer before inserting PC Cards. Locate the PC Card slot on the right side of the computer.
Page 68: Removing A Pc Card
Hardware Features Using PC Card slots Removing a PC Card Turn off the computer. Locate the PC Card eject button that corresponds to the slot in which your PC Card is installed. The top button releases a card in the upper slot. The bottom button releases a card in the lower slot.
Page 69: Using A Modem
Using a modem If you have a modem, you may have an internal modem or a PC Card modem. This section provides information on the internal modem. A modem allows you to: Access a bulletin board service (BBS) or the Internet. ❖...
Page 70 Hardware Features Using a modem Connecting the telephone cable to the RJ-11 modem jack Connect the other end to the wall jack. Connecting to a wall jack CAUTION: The modem is designed for use with a standard analog telephone line. Do not connect the modem to a digital telephone line.
Page 71: Determining Your Com Port
Now you’re ready to send a fax or use the modem to connect to an online service or the Internet (see “Using the Internet” on page 48). HINT: If you’re using a telephone line at home, disable Call Waiting before connecting through the modem. Call Waiting interrupts transmission.
Page 72: Using The Computer's Telephony Features
Hardware Features Using the computer’s telephony features Using the computer’s telephony features TECHNICAL NOTE: Windows NT does not support this feature. Your computer comes with RingCentral, an integrated telephony application that lets you use the computer’s built-in modem to: ❖ Place and receive telephone calls.
Page 73: Using Bulletin Board Services
Most computer companies offer a BBS as one way to provide customers with software updates and answers to their questions. Toshiba’s 24-hour BBS is a good source of Toshiba Utility files and technical bulletins. Discovering Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect.
Page 74: Recording Sounds With A Microphone
(Japan) ❖ On CompuServe, type go toshiba ❖ To access Toshiba’s BBS, set your modem to N81 and call (949) 837-4408 Recording sounds with a microphone You may record sounds through the built-in microphone or, using the microphone jack or line-in jack, from an outside source.
Page 75: Using An External Audio Input Device
Turn on the microphone. The internal microphone is automatically disabled. Once the external microphone is connected, the recording process is the same as with the built-in microphone. Using an external audio input device You can also record sounds from an external audio device, such as a stereo amplifier, tape deck, or CD player.
Page 76: Using External Speakers Or Headphones
Hardware Features Using external speakers or headphones Using external speakers or headphones To attach an external headphone: Locate the headphone jack on the back of the computer. It’s between the external microphone and line-in jacks. Using any necessary adapters, plug the cord from the external audio device into the headphone jack.
Page 77 Hardware Features Using external speakers or headphones Part I: Getting to Know Your Computer...
Page 78 Chapter Hard disk drive ..........55 External diskette drive .
Page 79: Chapter 4: Using Drives
Using Drives ng Drives This section explains how to use the various drives that are available with your Tecra 8000 Series notebook computer. Hard disk drive The removable hard disk drive (HDD) module allows you to carry your data without the computer. To remove the HDD module: Turn off the computer.
Page 80 Using Drives Hard disk drive Turn the computer over and remove the screw that secures the HDD. Removing the screw securing the HDD Press the two latches securing the cover. Press on the ridges until you hear a click. Lift the cover up and away from the computer to remove it. Removing the HDD cover Part I: Getting to Know Your Computer...
Page 81: External Diskette Drive
Grasp the HDD’s plastic handle and pull toward yourself to remove the module. Removing the HDD module To insert the HDD module: Turn the HDD module so the connector faces down. Insert the module into the slot, pressing firmly to ensure a good connection.
Page 82: Cd-Rom Drive
Your Tecra 8000 Series computer may have a Toshiba DVD- ROM drive and a Toshiba DVD Player that uses MPEG 2 hardware in your computer to play DVD video titles. This means the computer is able to play high-resolution, full-screen video at up to 30 frames per second.
Page 83: Using The Dvd-Rom Or Cd-Rom Drive
Using the DVD-ROM or CD-ROM drive If the DVD-ROM drive is not currently installed in the SelectBay, follow the instructions in “Swapping SelectBay modules” on page 37. HINT: Your DVD-ROM drive is designed to play Region 1 (North America) DVD-ROMs. Using the DVD-ROM or CD-ROM drive To insert a disc into the DVD-ROM or CD-ROM drive: Make sure the activity light is off.
Page 84 Using Drives Using the DVD-ROM or CD-ROM drive Pressing the eject button. HINT: The drive won’t open if the computer’s power is off. Grasp the drawer and pull it fully open. Opening the drive Hold the compact disc by its edges and check that it is free of dust.
Page 85 Using the DVD-ROM or CD-ROM drive Spindle Disc Positioning the disc on the spindle Gently press the disc onto the center spindle until you feel it click into place. CAUTION: Handle DVD and CD discs carefully, making contact only with the center hole and edge. Don’t touch the surface of the disc.
Page 86: Playing Cds
Using Drives Using the DVD-ROM or CD-ROM drive Playing CDs Windows comes with three programs for playing sound, video and animation CDs: CD Player is used to play an audio CD. This section explains ❖ how to use this program. ❖...
Page 87: Dvd Player Overview
HINT: To connect to a Dolby Digital Surround Sound decoder/receiver, you need a digital coaxial cable. The system does not support a fiber optic cable. Contact an electronics store or visit Toshiba’s Web site at www.pcsupport.toshiba.com for vendor information. Using Drives...
Page 88: Dvd Player Controls
Click DVD Video, then click DVD Video Player. Feature controls The DVD Player The Toshiba DVD Player resembles a standard home VCR, but it also has features that are unique to the DVD medium. Part I: Getting to Know Your Computer...
Page 89 Option controls Power Off Eject Open file Slider bar The Option controls This table summarizes the functions of the option controls. Button Function Power Off Stops all DVD functions and closes the DVD Video Player. Eject Ejects the disc from DVD-ROM drive. Open file Allows you to locate and open a specific DVD file.
Page 90 Using Drives DVD Player overview Button Function Option Provides access to the DVD Setup window which defines the default settings and operating parameters for the DVD player. Minimize Closes the DVD Player window and places a DVD Player button on the taskbar. Help Provides access to the DVD Player’s online help file.
Page 91 DVD feature controls The DVD feature controls The DVD feature controls allow you to choose how you want to view your DVD video. These controls provide options that are not available on other video platforms. Button Function Angle Allows you to view your DVD video from different camera angles (if supported).
Page 92: Directional Controls
Using Drives DVD Player overview Directional controls The DVD directional controls The DVD directional controls function like a standard VCR. Button Function Stop Stops the current selection. Play Plays the current selection. Previous Returns to the beginning of the previous chapter. Next Skips to the beginning of the next chapter.
Page 93: Setting Up The Dvd Player
Button Function Fast Forward Provides two different speeds for advancing through the video. Clicking on the button allows you to switch speeds. Pause Temporarily stops the video and freezes the current frame on the screen. Frame Advances the video one frame at a time when the Pause is Advance also selected.
Page 94 Using Drives DVD Player overview The Player Setup dialog The Player Setup dialog box is divided into four parts that control the DVD Player’s operations. General tab ❖ Video tab ❖ Language tab ❖ Information tab ❖ Part I: Getting to Know Your Computer...
Page 95: General Tab
General tab The General tab has three sections that define the action taken by the DVD Player when it starts and when you insert a disc in the DVD-ROM drive. The General tab Click the Option button on the DVD Player, then click Settings.
Page 96 Using Drives DVD Player overview DVD setting The Transform Filter Properties dialog box To define the audio and video settings for your DVD Player, ❖ click the Property button in the DVD setting section. The Transform Filter Properties dialog box appears. To listen to your DVD video through an AC-3 digital surround sound receiver, click AC-3/MPEG under the Digital Audio Output.
Page 97: Video Tab
Open DVD file ❖ Open DVD file and play ❖ When DVD media is inserted Define the action taken by the DVD player when you insert a DVD video in the DVD-ROM drive by making a selection and clicking the button next to the option. The options are: Do not open DVD file ❖...
Page 98 Using Drives DVD Player overview The Video tab Click the Video tab. The Player Setup displays the Video tab that is made up of two sections. Make your selections in each section. Click OK to apply your changes. TV Shape The TV Shape section provides options for defining the Video Window Mode and Video Window Size.
Page 99 Pan-Scan: stretches the video display vertically to fill the ❖ video window completely. A similar mode is used to reformat movies for videotape. TECHNICAL NOTE: The Video Window Mode settings are only supported when the DVD video is viewed in wide- screen mode.
Page 100: Language Tab
Using Drives DVD Player overview Language tab The Language tab defines the default language settings for the DVD Player. To set language options, follow these steps: Click the Option button, then click Settings. The Player Setup dialog appears. The Language tab Click the Language tab.
Page 101: Information Tab
Menu Language: This option defines the language preference to be used in the menus displayed by the DVD video. If the language is not supported by the video, the video’s default language is used. Make your selections. Click OK to apply your changes. Information tab This tab provides information about the particular DVD video that is inserted in the drive, such as number of titles, chapters, subtitles,...
Page 102: Playing A Dvd Video
Using Drives Playing a DVD video Playing a DVD video Once you have set up the DVD Player, you are ready to play a DVD video. Playing a DVD video is as easy as playing a video tape in a VCR. The directional controls operate the same way. To play a DVD video: Open the DVD Player by double-clicking the DVD video icon on your desktop.
Page 103: Choosing A Language
To get the sharpest picture for your movie, double-click the video window. The video window maximizes to full screen, and the movie window sizes to 720 x 480. Every item on your desktop, including the DVD Player, disappears from view. To return to the desktop and the DVD Player, double-click the screen.
Page 104: Using The Search Feature
Using Drives Playing a DVD video Your language selection appears in the DVD Player control panel. Changing subtitles You can set subtitles for your DVD Player by performing the following procedures: Click the Subtitle Feature button in the DVD Player control panel.
Page 105 The Search dialog box Select Title - Chapter Search. Choose a chapter number from the Chapter drop-down menu. Click OK. The video advances to the beginning of the chapter you selected. Time Search Some DVD videos support the Time Search feature which identifies a specific location measured in hours, minutes, and seconds from the beginning of the video.
Page 106 Using Drives Playing a DVD video Click OK. The video advances to the search location you specified. Slider bar If your DVD video supports the Time Search feature, the Slider bar displays the current playback position. You can also move the Slider bar to rapidly skip through the video.
Page 107 Using Drives Playing a DVD video Part I: Getting to Know Your Computer...
Page 108 Chapter Running the computer on battery power ......85 Using Hibernation mode (Windows 95 and Windows 98) ... 88 What to do when the battery alarm sounds .
Page 109: Chapter 5: Power Management
It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba or your network administrator. We recommend you leave these features active, so your computer will operate at its maximum energy efficiency.
Page 110: Charging The Batteries
The backup battery provides the power to store information about the system when you suspend the computer using the Windows 95/Windows NT Suspend command, Windows 98 Standby command, or Toshiba’s Resume Mode. The backup battery maintains this information for up to eight hours after the main battery discharges completely.
Page 111: Monitoring Battery Power
HINT: Be careful not to confuse this light ( ) with the on/off light ( ). When the on/off light flashes orange, it indicates that the system is suspended (using Toshiba’s Resume Mode or the Windows 95/Windows NT Suspend command, or Windows 98 Standby command).
Page 112: Using Hibernation Mode (Windows 95 And Windows 98)
Hibernation is enabled in Windows 95 and Windows 98. To enable Hibernation in Windows 95: From the Control Panel, double-click the Power Management icon. Select the Toshiba Power Extension tab. Select Enable Hibernate Support. To enable Hibernation in Windows 98: From the Control Panel, double-click the Power icon.
Page 113: What To Do When The Battery Alarm Sounds
What to do when the battery alarm sounds Set your default options as needed. HINT: Toshiba recommends using Hibernation because if you use Resume or Standby mode and your backup battery dies, you will lose what was saved. In Hibernation, your work will not be lost.
Page 114: Starting Where You Left Off
❖ Windows NT) or click Start, Shutdown and then select Standby (Windows 98). Turn on Toshiba’s Resume Mode and press the power button. ❖ The Windows Suspend/Standby feature is the easier way to suspend the computer. However, you’ll have to use Resume Mode...
Page 115: Changing Batteries
❖ Turn off automatically when you haven’t used it for a set amount of time. To turn on Toshiba’s Resume Mode in Windows, you use a special key combination (hot key): Press pop-up window. The Resume Mode pop-up window While continuing to press Resume On.
Page 116 Power Management Changing batteries To change the battery: Save your work. Turn off the computer. Remove all cables connected to the computer. Turn the computer over. Slide the battery lock to the side. Unlocking the battery Pull the battery module toward you to slide it out. Removing the discharged battery Part I: Getting to Know Your Computer...
Page 117: Taking Care Of Your Battery
Lift the discharged battery out of the computer. WARNING: If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in “Taking care of your battery” on page 93.
Page 118: Safety Precautions
Power Management Taking care of your battery Safety precautions Never try to disassemble a battery pack. ❖ Don’t overcharge or reverse charge a battery. Overcharging ❖ will shorten its life and reverse charging could destroy it, causing the release of toxic fumes. ❖...
Page 119: Conserving Power
Enable Resume Mode, which saves power when you turn off ❖ the computer and turn it back on again. Use Toshiba’s power-saving options. ❖ These power-saving options control the way in which the computer is configured. By using them, you can greatly increase the length of time you can use the computer before you need to recharge the battery.
Page 120: The Easy Way-Choosing A Power Usage Mode In
The easy way—choosing a power usage mode in Windows 95 and Windows 98 Go to Start, Settings, Control Panel. Click on the Power icon. Multiple options can be set in the Power Schemes and Toshiba Power Extensions tabs. If you are working in MS-DOS usage mode in TSETUP.
Page 121: Additional Options For Power
Depending on the amount of time you spend away from external power sources, the capacity of one battery pack may be sufficient for your needs. However, if you need more portable power, Toshiba provides these options: Purchase extra battery packs. ❖...
Page 122 Chapter Hot keys for Windows 95, Windows NT ......99 Hot keys for Windows 98 ........101 Fn-esse .
Page 123: Chapter 6: Hot Keys And Function Keys
Toshiba’s Fn-esse utility. Hot keys for Windows 95, Windows NT Hot keys are keys that, pressed in combination with the turn system features on and off.
Page 124: Battery Save Mode
Hot Keys and Function Keys Hot keys for Windows 95, Windows NT Battery save mode This hot key displays the power usage pop-up window and cycles through the battery save modes: Full Power, Low Power, and User Settings. For Windows NT units, the power usage modes are: Full Power, High Power, Medium Power, Low Power and User Setting.
Page 125: Hot Keys For The Keyboard
Hot keys for the keyboard This hot key turns the cursor control overlay on and off. This hot key turns the numeric overlay on and off. This hot key turns the scroll lock feature on and off. Hot keys for Windows 98 Power mode This hot key displays the power usage pop-up window and cycles through the power modes: Home/office desk,...
Page 126: Starting Fn-Esse
You can assign any key that is not associated with a hot key or a keyboard overlay. Starting Fn-esse Click Start, then point to Programs. Point to Toshiba Utilities, then click Fn-esse. The Fn-esse icon appears on the taskbar. Click the Fn-esse icon on the taskbar. The Fn-esse keyboard appears.
Page 127: Assigning A Key To A Program Or Document
Keys associated with a popup list have a small dot on the ❖ upper-left corner of the key. Assigning a key to a program or document There are three ways to assign a key to open a program or document: Drag-and-drop.
Page 128: Viewing Existing Key Assignments
Hot Keys and Function Keys Fn-esse The program or document is now associated with the key you just selected. To open the program or document, press the appropriate key from within any Windows program. Using a popup list To assign a key to open a program or document from a popup list: Click the desired key in the Fn-esse keyboard with the secondary button.
Page 129: Changing Or Removing Existing Key Assignments
This box lists all the key assignments and the program or document to which each key is assigned. To view items in a popup list, click the Expand popup lists check box. Changing or removing existing key assignments In the Fn-esse keyboard, click the key you wish to change with the secondary button.
Page 130: Cursor Control Overlay
Hot Keys and Function Keys Working with the keyboard Cursor control overlay The keys with the white arrows and white symbols on the left front are the cursor control overlay. This illustration highlights the cursor control overlay keys: The cursor control overlay You can use these keys to: Move the cursor up, down, left or right on the screen.
Page 131: Numeric Keypad Overlay
The keys of the cursor control overlay also act as a numeric overlay, providing the numeric keys of a ten-key numeric keypad. Numeric keypad overlay The keys with the numbers on the right front of the keycaps are the cursor control overlay. This illustration highlights the numeric overlay keys: The numeric keypad overlay To activate the numeric keypad overlay, hold down the...
Page 132 Chapter Problems that are easy to fix ........109 Problems when you turn on the computer .
Page 133: Chapter 7: Troubleshooting Guide
Troubleshooting Guide Some problems you may encounter when using your Tecra 8000 Series computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems yourself. It covers the problems you are most likely to encounter.
Page 134: Problems When You Turn On The Computer
Troubleshooting Guide Problems when you turn on the computer Turn off the computer and any peripheral devices connected to it. This includes your printer and any other external devices. Check that the wall outlets are working by plugging in another appliance such as a lamp. Check that the power cables are firmly plugged in.
Page 135 Problems when you turn on the computer If the computer will not start after it has been turned off for a while, remove the battery and reinsert it. For instructions on removing the battery, see “Changing batteries” on page 91. The computer starts but, when you press a key on the keyboard or touch the AccuPoint, nothing happens.
Page 136 CAUTION: Before using the Toshiba Companion Diskette, make sure that your computer has the same operating system as that which is stored on the Toshiba Companion Diskette or additional problems may result. Insert a Toshiba Companion Diskette into the diskette drive.
Page 137 The message “Welcome to Toshiba Companion Diskette” appears on your screen. Press Enter. The Toshiba Companion Diskette Main Menu displays a list of options. Choose Exit to DOS, and press The MS-DOS prompt A:> appears. Type , then press...
Page 138: Resolving A Hardware Conflict
If the problem persists, try restarting the computer with the Toshiba Companion Diskette or another reliable system disk in the diskette drive. Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using Windows Help to troubleshoot the problem first.
Page 139: A Plan Of Action
Click If you have a hardware conflict and follow the steps. If there is still a problem, Windows 95/Windows 98 should display a message that explains what the conflict is. If this happens, you may need to solve the problem on your own. A plan of action The smooth operation of the system depends on the interaction of all devices, programs and features.
Page 140: Checking Device Properties
Troubleshooting Guide Resolving a hardware conflict Plug and Play TECHNICAL NOTE: Windows NT does not support Plug and Play. With Plug and Play and Windows 95/Windows 98, avoiding hardware conflicts is easy. Plug and Play is a computer standard that helps the system BIOS (basic input/output system) and Windows 95/Windows 98 automatically assign system resources to Plug and Play-compliant devices.
Page 141: Fixing Device-Related Problems
To check a device’s properties: Click Start, then point to Settings, and click Control Panel. Double-click the System icon. Windows 95/Windows 98 displays the System Properties dialog box. Click the Device Manager tab. Double-click the device type. To view the properties, double-click the device. Windows 95/Windows 98 displays the Device Properties dialog box, which provides various tabs to choose from.
Page 142: Memory Card Problems
Troubleshooting Guide Fixing device-related problems Memory card problems Incorrectly connected or faulty memory cards may cause errors that seem to be device-related. So it’s worthwhile checking for these first: Make sure the computer isn’t in Resume Mode. Click Start, then click Shut Down. Windows displays the Shut Down Windows dialog box.
Page 143: Power And The Batteries
Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery, real-time clock (RTC) battery and backup battery). Power problems are interrelated. For example, a faulty power cable will neither power the computer nor recharge the batteries.
Page 144: Keyboard Problems
Let the battery discharge completely, then try charging it again. Check the power-saving features in Toshiba Utilities (Windows 95) or TSETUP (Windows 95/98) or Power Saver (Windows NT). Have you added a device, such as a PC Card or...
Page 145: Accupoint Problems
You’ve connected an external keyboard and Windows displays one or more keyboard error messages. The keyboard you connected may be defective or incompatible with the computer. Try using a different make of keyboard. Nothing happens when you press the keys on the external keyboard.
Page 146: Display Problems
Troubleshooting Guide Fixing device-related problems Display problems The screen is blank. Display Auto Off may have taken effect. Press any key to reactivate the screen. You may have activated the instant security feature by pressing simultaneously. Enter your user-level password if you have registered one, or press If you are using the built-in screen, try changing the display priority to make sure it is not set for an external monitor.
Page 147: Disk Drive Problems
The display is set to a simultaneous display mode (LCD/CRT or LCD/TV) and the external display device doesn’t work. Make sure the resolution of the external display device and the internal display match. For example, if the external device is only capable of displaying resolutions up to 800 x 600, you’ll need to change the resolution of the internal display to 800 x 600.
Page 148 Troubleshooting Guide Fixing device-related problems Click Start, then point to Programs. Point to Accessories, then point to System Tools. Click ScanDisk. Windows 95/Windows 98 opens the ScanDisk window. In Windows NT, run the Disk Administrator Error Checking tool to check disk volumes for errors. You can also save a copy of your disk configuration information.
Page 149 Click Disk Defragmenter. Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data by using utility software, which is available from your network administrator. Some programs run correctly but others do not.
Page 150: Modem Problems
Troubleshooting Guide Fixing device-related problems The drive can’t read a diskette. Try another diskette. If you can access the second diskette, the first diskette (not the diskette drive) is probably causing the problem. Run ScanDisk on the faulty diskette. If you’re using the diskette drive externally, unplug the cable and plug it back in to make sure the connection between the diskette drive cable and the port is secure.
Page 151: Problems With The Cd-Rom Or Dvd-Rom Drive
The modem is on, configured properly, and still won’t transmit or receive data. Make sure the line has a dial tone. Connect a telephone handset to the line to check this. The other system may be busy or off line. Try making a test transmission to someone else.
Page 152: Sound System Problems
Troubleshooting Guide Fixing device-related problems Some discs run correctly but others do not. Check the type of disc you are using. The DVD-ROM drive supports Digital Versatile Discs (DVDs), ISO 9660 and CD Plus data CDs, audio CDs and photo CDs. The CD-ROM drive supports ISO 9660 and CD Plus data CDs, audio CDs and photo CDs.
Page 153: Optional Devices
The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers. It occurs in any sound system when input from a microphone is fed to the speakers and the speaker volume is too loud. Adjust the volume control.
Page 154 Troubleshooting Guide Fixing device-related problems Some card manufacturers use special software called enablers to support their cards. Enablers result in nonstandard configurations that can cause problems when installing another PC Card. If Windows doesn’t have built-in drivers for your PC Card and the card didn’t come with a Windows driver, it may not work under Windows.
Page 155 Resolving PC Card problems Here are some common problems and their solutions: The slots appear to be dead. PC Cards that used to work no longer work. To view the PC Card status if you have Windows 95/Windows 98 installed: Click the My Computer icon with the secondary button, then click Properties.
Page 156 Hardware Setup icon. To check this in Windows NT: click Start, select Programs, select Toshiba Utilities, click Hardware Setup, then select the Hardware Options button and the PC Card tab. You will need to reboot the machine in order for changes to take effect.
Page 157: Printer Problems
42, but the system still reports the controller with a yellow “!”. The PCMCIA.INI file may not be installed on your computer. Install it, referring to the Toshiba Configuration Builder CD Instructions for the installation procedure. A PC Card error occurs.
Page 158: Dvd Operating Problems-Windows 95/Windows 98
Troubleshooting Guide DVD operating problems–Windows 95/Windows 98 For Windows NT, make sure the Parallel Port Mode option in System Setup is set correctly for your printer. If your printer is not ECP-compatible, this option should be set to Std. Bi-Direct. If your printer is ECP- or IEEE 1284-compliant, make sure you have an IEEE 1284 printer cable.
Page 159 See “Checking device properties” on page 116 for instructions on using Device Manager to view the DVD- ROM properties. Check the Toshiba web site for new information on DVD- ROM drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 160 Troubleshooting Guide DVD operating problems–Windows 95/Windows 98 Deselect Shut off Monitor. The DVD-ROM Player does not play DVD videos. All the buttons are inactive. Verify the correct drive letter is assigned to the DVD-ROM drive. The General tab Click the Option button on the DVD-ROM Player, then click Settings.
Page 161 480 or 800 x 600 can cause distortion. If your video resolution is set to 800 x 600, do the following to disable Stretch: Click Start, point to Settings, then click Control Panel. Double-click Toshiba Hardware Setup and then select the Display tab. Under the LCD Display Stretch, click Disabled, and then click OK.
Page 162 Troubleshooting Guide DVD operating problems–Windows 95/Windows 98 The screen saver runs while you are watching a movie or title. If the screen saver is enabled, it runs on top of any movie or title you are watching. To disable the screen saver using the following steps: Click Start, point to Settings, then click Control Panel.
Page 163 DVD operating problems–Windows 95/Windows 98 Click the Option button on the DVD-ROM Player, then click Settings. The Player Setup dialog displays the General tab. The General tab In the DVD Setting section, click the Property button. The Transform Filter Properties dialog appears. The DVD Transform Filter Properties dialog box To listen to your DVD video through: an AC-3 digital surround sound receiver, click AC-3/...
Page 164 Troubleshooting Guide DVD operating problems–Windows 95/Windows 98 a non-Dolby digital receiver, click PCM under Digital ❖ Audio Output. Click OK to apply your settings. If you still do not hear sound from your surround sound receiver, contact your network administrator for support. No video window appears on your S-video or composite video device.
Page 165: Dvd-Rom Error Messages
“Program Error” or “VPM” error messages The display drivers for your Tecra 8000 Series DVD-ROM may be installed incorrectly. To install the display drivers, use the Configuration Builder CD that shipped with your computer.
Page 166: Developing Good Computing Habits
Troubleshooting Guide Developing good computing habits Developing good computing habits This section suggests some good habits to develop so you are prepared if things go wrong. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes.
Page 167: If You Need Further Assistance
Consult your authorized Toshiba representative, or your ❖ network administrator. For the number of a Toshiba dealer near you in the United States, call (800) 457-7777. Contacting Toshiba If you still need help and suspect that the problem is hardware- related, Toshiba offers a variety of resources to help you.
Page 168 Toshiba’s Bulletin Board Service Toshiba’s Bulletin Board Service (BBS) is available 24 hours a day, and is free of charge to anyone with a PC and a modem. From Toshiba’s BBS, you can download files and obtain other useful information.
Page 169: Toshiba's Worldwide Offices
For technical support, call Toshiba at: (800) 457-7777 from inside the United States ❖ (949) 859-4273 from outside the United States ❖ For the number of a Toshiba dealer near you in the United States, call (800) 457-7777. Toshiba's worldwide offices Argentina Acron, S.A.
Page 170 Santa Fe de Bogotá, Colombia Denmark Scribona Danmark A/S Naverland 27 DK2600 Glostrup Denmark France Toshiba Systèmes (France) S.A. 7, Rue Ampère 92804 Puteaux Cédex France Part I: Getting to Know Your Computer Belgium Toshiba Information Systems Benelux (Belgium) B.V.
Page 171 Viale Certosa 138, 20156 Milano Italy Luxembourg Same as Belgium Morocco C.B.I. 22 Rue de Béthune Casablanca Morocco New Zealand Toshiba (New Zealand) Pty. Limited Level 4, 3 Ferncroft Street Grafton Auckland New Zealand Part I: Getting to Know Your Computer...
Page 172 Troubleshooting Guide Toshiba's worldwide offices Norway Scribona Norge A/S Toshiba PC Service Stalfjaera 20 P.O. Box 51 Kalbakken 0901 OSLO 9 Norway Poland TECHMEX S.A. ul. Partyzantów 71, 43-316 Bielsko-Biala 01-059 Warszawa Poland Slovakia HTC s.r.o. Kukucinova 26 831 03 Bratislava...
Page 173 Switzerland Ozalid AG Herostrasse 7 8048 Zürich Switzerland United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States Troubleshooting Guide Toshiba's worldwide offices United Kingdom Toshiba Information Systems (U.K) Ltd. Toshiba Court Weybridge Business Park...
Page 175: Part Ii: Technical Reference
ECHNICAL EFERENCE What’s in Part II This part documents the Toshiba utility programs that come with your computer. If you’re new to computers, you can skip this part until you need it. If you’re experienced, you may find explanations for the options you’re using...
Page 176 Chapter Using TSETUP ..........153 Using Hardware Setup .
Page 177: Chapter 8: System Setup
System Setup The Tecra 8000 Series has several user-definable settings and features available for customizing the machine to your specific needs and preferences. Using TSETUP TSETUP is much like Hardware Setup, but it is DOS-based. To access TSETUP: Turn off the computer.
Page 178: Using Hardware Setup
System Setup Using Hardware Setup Use TSETUP to view or change the Tecra 8000 Series custom settings and features. HINT: TSETUP does not run from within Windows 95,Windows 98, or Windows NT. You must exit Windows and run TSETUP while in MS-DOS mode.
Page 179: Using Hardware Setup In Windows Nt 4.0
Using Hardware Setup in Windows NT 4.0 To access Hardware Setup in Windows NT 4.0, go to Start, Programs, Toshiba Utilities, and then Hardware Setup. System Setup Using Hardware Setup Part II: Technical Reference...
Page 180 System Setup Using Hardware Setup There are 12 tabs: Boot Priority Option ❖ Allows you to change the sequence in which your computer searches the various drives for the operating system. ❖ Pointing Device Allows you to use both the AccuPoint and external pointing devices together or have the system auto-select one.
Page 181 CPU Cache ❖ Allows you to change the cache default settings. Parallel/Printer ❖ Allows you to configure the parallel port default settings. By changing any of the options that appear in the dialog boxes and clicking Apply, you can reconfigure that function. Any options that you change will become default settings when you reboot your system.
Page 182 Chapter Using a password in Windows 95 and Windows 98 ....159 Using a password in Windows NT Workstation 4.0 ....175...
Page 183: Chapter 9: Keeping Your Files Safe
When you set a password, you must enter the password before you can work on your computer again. Toshiba supports five types of passwords on the Tecra 8000 Series computer: A power-on (user-level) password requires you to enter the ❖...
Page 184: Setting A User-Level Password
You may create a user-level password using either Toshiba Utilities or TSETUP. This section describes how to create a user- level password in Toshiba Utilities and how to use it as an instant and power-on password. CAUTION: Make sure you use a password you can remember easily.
Page 185 Once you have used the diskette, you must reset your password and create another password service diskette. You can set (register) a user-level password in either Toshiba Utilities or TSETUP. If you use TSETUP, you can create a password service diskette.
Page 186 Keeping Your Files Safe Using a password in Windows 95 and Windows 98 Select Restart the computer in MS-DOS mode, then click Yes, or OK, as appropriate. Windows 95/Windows 98 shuts down the computer, then restarts it in MS-DOS mode and displays a system prompt. Type c:\dos\tsetup TSETUP displays a system setup screen.
Page 187 Using a password in Windows 95 and Windows 98 If the two passwords don’t match TSETUP displays an error message. Repeat steps 8 and 9 to enter the password again. 10 Press to save your change. TSETUP asks you to confirm your choice. 11 Press to confirm you want to quit.
Page 188: Power-On Password
Keeping Your Files Safe Using a password in Windows 95 and Windows 98 Power-on password Whenever you start your computer with a power-on (user-level) password in effect, the computer prompts you to enter the password before it goes through its normal startup procedure. The password operates regardless of whether the computer is in Resume Mode.
Page 189: Using An Instant Password
Point to Toshiba Utilities. Working with supervisor-level passwords When a supervisor-level password is set, you must enter the supervisor password to make changes using Toshiba Utilities or TSETUP. Setting a supervisor-level password To set a supervisor-level password, follow these steps: In Windows 95/Windows 98, click Start, then click Shut Down.
Page 190 Keeping Your Files Safe Using a password in Windows 95 and Windows 98 Windows 95/Windows 98 shuts down the computer, then restarts it in MS-DOS mode and displays a system prompt. Type c:\dos\svpw The Supervisor Password program starts and asks if you want to register (set) a password.
Page 191: Setting A Hard Disk Drive Password
Using a password in Windows 95 and Windows 98 Type your password and press Once again, the Supervisor Password program displays an asterisk (*) for each character you type. The Supervisor Password program indicates that no password is registered. Restart your computer to return to Windows 95/Windows 98. Setting a hard disk drive password Your computer comes with a program preinstalled that lets you set two types of hard disk drive passwords, User and Master.
Page 192: Setting A Hard Disk Drive Master Password
Keeping Your Files Safe Using a password in Windows 95 and Windows 98 Setting a hard disk drive Master password CAUTION: If you choose to set a hard disk drive User password, it is strongly recommended that you set a hard disk drive Master password as well.
Page 193 Using a password in Windows 95 and Windows 98 Type a password of up to ten characters and press CAUTION: Make sure you choose a hard disk drive Master password you can remember easily. If you set a hard disk drive User password and later forget the password or lose your password diskette, you will need to enter the hard disk drive Master password in order to access your hard disk.
Page 194 Keeping Your Files Safe Using a password in Windows 95 and Windows 98 Setting a hard disk drive User password If your diskette drive is not installed in the SelectBay, connect the external diskette drive or swap drives in the SelectBay. To swap drives, see “Using PC Card slots”...
Page 195 YOU WILL NEVER BE ABLE TO ACCESS YOUR HARD DISK AGAIN. Toshiba will not be held responsible for any loss of data, any loss of use or access to your hard disk drive, or for any other losses to you or any other person or organization that results from the loss of access to your hard disk drive.
Page 196 Keeping Your Files Safe Using a password in Windows 95 and Windows 98 To exit without setting a password, type The hard disk drive User password will be registered the next time you restart the computer. Each time you start the computer from the hard disk, the system will prompt you to enter your password.
Page 197: Deleting A Hard Disk Drive Master Password
Using a password in Windows 95 and Windows 98 If the password you typed matches the registered hard disk drive User password, the password is deleted. Restart the computer for your changes to take effect. Deleting a hard disk drive Master password HINT: You must delete the hard disk drive User password before you can delete the hard disk drive Master password.
Page 198: Using An Undock (Eject) Password
NoteDock II Enhanced Port Replicator. This protects both your computer and your data. HINT: You must register a password in Toshiba Utilities or TSETUP before you can use the Undock password option. This section provides instructions for turning on the Undock password option through Toshiba Utilities.
Page 199: Using A Password In Windows Nt Workstation 4.0
You may create a user-level password using either Toshiba Utilities or System Setup. This section describes how to create a user-level password in Toshiba Utilities and how to use it as an instant and power-on password. CAUTION: When you register a password in Toshiba Utilities, you cannot create a password service diskette.
Page 200: Protecting Against Forgetfulness
Keeping Your Files Safe Using a password in Windows NT Workstation 4.0 Click the Registered radio button in the User Password section and then follow the prompts to register your password. You must reboot the machine in order for changes to take effect.
Page 201 Using a password in Windows NT Workstation 4.0 Release the key. Press The system displays the first System Setup screen. Press to move to the PASSWORD section of the screen. Press the spacebar. System Setup asks you to enter a new password. Type a password of one to 16 characters and press You may use any combination of letters and numbers in your password.
Page 202: Using The Power-On Password
Keeping Your Files Safe Using a password in Windows NT Workstation 4.0 System Setup creates the password service diskette and displays a message when it’s finished. 14 Remove the diskette and press any key to continue. System Setup closes, returning you to the system prompt. The next time you start the computer your password will be in effect.
Page 203: Instant Password
Using a password in Windows NT Workstation 4.0 Insert the password service diskette into the diskette drive and press Enter The system prompts you, “ CAUTION: The password service diskette is not reusable. Once you use it, you must create a new diskette, even if you set the same password.
Page 204: Disabling A User-Level Password
YOU WILL NEVER BE ABLE TO ACCESS YOUR HARD DISK AGAIN. Toshiba will not be held responsible for any loss of data, any loss of use or access to your hard disk drive, or for any other losses to you or any other person or organization that results from the loss of access to your hard disk drive.
Page 205 YOU WILL NEVER BE ABLE TO ACCESS YOUR HARD DISK AGAIN. Toshiba will not be held responsible for any loss of data, any loss of use or access to your hard disk drive, or for any other losses to you or any other person or organization that results from the loss of access to your hard disk drive.
Page 206 Keeping Your Files Safe Using a password in Windows NT Workstation 4.0 Click the User button. A drop down box appears which lists all available hard drives. When you first buy your machine there should be only one hard drive listed. Click Register, then click OK.
Page 207 18 Click Exit to return to the Toshiba Hard Disk Password Utilities dialog box. Click OK. You are prompted to reboot the computer. The hard disk drive password will be registered the next time you restart the computer.
Page 208: Using An Eject Password
The eject password is the same as the power-on and instant passwords. HINT: You must register a password in Toshiba Utilities or System Setup before you can use the eject password option. Refer to “Creating a user-level password” on page 175.
Page 209 Keeping Your Files Safe Using a password in Windows NT Workstation 4.0 Part II: Technical Reference...
Page 210 Chapter Industry standard architecture ........187 System management ......... 189 Security management .
Page 211: Chapter 10: Managing Your Tecra 8000 Series Computer
IT operations. System management and computer security features specific to many of the latest notebooks, including the Tecra 8000 Series, are outlined briefly in this section. Industry standard architecture...
Page 212: Wired For Management
Industry standard architecture Wired for Management Adherence to the Wired for Management (WfM) Baseline allows Toshiba to deliver systems with superior integrated capabilities for central administration, remote system installation and configuration, off-hours maintenance and constant PC health monitoring. The specification defines the requirements for...
Page 213: Operating System Compatibility
Operating system compatibility Additionally, the Tecra 8000 Series computers, like all Toshiba computers, bear the Microsoft Hardware Compatibility logo. The logo indicates the unit has passed a series of tests that verify the compatibility of Toshiba’s hardware systems and associated...
Page 214: Asset Management
LDCM v.3.3 is designed to support Windows 98. Additionally, Toshiba has added specific notebook enhancements for the Tecra 8000 Series computer to LDCM. As a result, the end user or IT technician has available: Battery pack information and status ❖...
Page 215: Configuration Management
How many are over 80 percent full? The Tecra 8000 Series offers two features that help the IT administrator handle inventory management. First, it provides automatic recognition and recording of the serial numbers of the computer and key components, including hard disk drives, batteries and the Network Dock.
Page 216: Fault Management
Managing Your Tecra 8000 Series Computer System management that ships with the Tecra 8000 Series gives users the ability to completely recover their systems, reinstall individual software or create a completely new configuration. Custom configuration is possible through a database that contains automated installations...
Page 217 Enhanced BIOS POST Toshiba incorporates an enhanced BIOS POST (Power On Self Test) into the Tecra 8000 Series boot process. Once the machine is powered on, the system executes a testing sequence prior to loading the operating system, including analysis of the memory subsystem, display and keyboard controllers, and hard drive.
Page 218: Enterprise Management Software Compatibility
By supporting and integrating a wide variety of system management functions with enterprise management applications, Toshiba has assured that the Tecra 8000 will work well within a managed enterprise environment. Integrated DMI support provides extensive system information to DMI-enabled enterprise management applications.
Page 219: Advanced Networking Features Via The Network Dock
❖ identified Advanced networking features via the Network Dock The Tecra 8000 Series offers a number of advanced networking features that become available when the computer is attached to the Network Dock. These include Wake on LAN and Alert on LAN, as described below.
Page 220: Security Management
Managing Your Tecra 8000 Series Computer Security management Service Boot Service Boot is a BIOS-based manageability solution that allows a computer to be booted up without any operating system on the hard disk, or with a damaged image, attaching to a (usually server- based) configuration tool.
Page 221: System Password In Flash, Not Cmos
Managing Your Tecra 8000 Series Computer System password in Flash, Not CMOS Toshiba addresses security concerns in a number of ways. Across Toshiba’s product lines, the system password for user entry is located in flash memory, as opposed to CMOS. CMOS is battery- powered memory.
Page 222: Hard Disk Drive Password
Managing Your Tecra 8000 Series Computer Security management Hard disk drive password For added security of data, Toshiba has implemented the hard disk drive password feature across all portable platforms. Should the hard drive be removed, transferred and installed into another...
Page 223: Cable Connection
Kensington-capable anti-theft locking device embedded into the system tool. Using an optional compact Kensington lock and durable galvanized steel cable, users may secure their Tecra 8000 Series computer to their table or desk, safe from potential theft or damage. Part II: Technical Reference...
Page 225 PPENDIXES What’s in Part III This part provides additional technical information about the computer. Review this material if you have additional questions or need additional information.
Page 226 Appendix Built-in features ..........203 Optional accessories and devices .
Page 227: Appendix A: Features And Specifications
Features and Spec c ifications This appendix lists the features of the computer and summarizes its specifications. Built-in features This section lists the computer’s features. Technology and processor Microprocessor 366 MHz, Intel Pentium ll processor with dual independent bus architecture -or- 400 MHz, Intel Pentium ll processor with dual independent bus architecture...
Page 228: Part Iii: Appendixes
Features and Specifications L1 cache 32 KB write-back (16 KB for code and 16 KB for data) level one cache L2 cache 256 KB integrated L2 cache Pipelined Burst Synchronous SRAM (64-bit bus width) PCI Bus High performance PCI system bus supports external PCI docking capability CardBus support Supports CardBus PC Cards, enabling connection to...
Page 229 Ion (Li-Ion) battery pack Secondary Battery 7.2V x 40mAh Lithium Ion (Li-Ion) battery provides power for special memory features, such as Resume Mode (Available through the Toshiba Accessories Catalog) RTC battery 2.4V x 40mAh Lithium Ion (Li-Ion) battery provides power for the internal real time clock and calendar...
Page 230 Features and Specifications Ports Composite video NTSC/PAL connector lets you connect the computer to out port an external video device such as a standard television, using an RCA cable DC IN socket Lets you connect the computer to AC power, using the AC adapter and power cable Expansion port 240-pin port lets you connect an optional Desk Station...
Page 231 USB port Supports USB peripherals Standard hardware Memory options The Tecra 8000 Series comes with 0 RAM (expandable to 256 MB). The amount of RAM is specified by the customer. Display options 12.1-inch (measured diagonally) active matrix Thin...
Page 232 Features and Specifications Graphics NeoMagic 2200 graphics controller with 32-bit PCI local bus and 2.5 MB integrated 64-bit synchronous graphics RAM, supports external monitors and high- resolution, high-color video modes Telecommunication Integrated V.90 K56flex modem Integrated speakerphone and answering machine capabilities through RingCentral software on computers with Windows 95 and Windows 98 Protocols...
Page 233: Special Features
Yamaha Station MPEG-1 Audio/ Mediamatics Arcade Pak™ Video DVD Player Toshiba DVD Player (with DVD Configurations and optional DVD drive kit) Special features Resume Mode Electronic bookmark that records what you’re doing when you turn off the computer and returns you to the...
Page 234 Features and Specifications Advanced Power TSETUP allows you to adjust the system’s power Management consumption levels The power management utility in Windows 95 and Windows 98 can be accessed directly in Control Panel Windows NT 4.0 uses Power Save to set the system’s power consumption levels Integrated Advanced Power and Configuration Interface (ACPI) V1.0 support provides Plug and Play...
Page 235 Optional accessories and devices This section lists the options available for the computer. SelectBay modules CD-ROM drive 5.25-inch 24X (maximum) speed (2394 Kbps average module transfer speed), MPC-compliant, photo-CD capable CD-ROM drive module lets you play music from CDs (compact discs) and run programs from CD-ROMs DVD-ROM drive 5.25-inch DVD-ROM drive allows you to play both module...
Page 236: Power Devices
Features and Specifications Weight Saver Insert Honeycombed plastic piece designed to reinforce your Module SelectBay when no other module is in it. This is especially useful if you want to travel light. Power devices Battery charger Noteworthy automobile power adapter Additional battery packs Memory modules 32 MB...
Page 237 Desk Station V Optional docking station that provides access to the Plus following: built-in SCSI-II port, internal IDE connector, two Type III PC Card slots, slots for ISA or PCI expansion cards, drive bay for an extra half-height 5.25- inch drive, SelectBay for diskette drive, CD-ROM drive module or hard drive module, headphone jack, microphone jack, PS/2 mouse port, PS/2 keyboard port, audio line-in jack, audio line-out jack, serial port, video...
Page 238: Specifications
Features and Specifications Specifications Physical dimensions Weight 6.39 lbs with 13.3 inch display and diskette drive module 6.5 lbs with 13.3 inch display and CD-ROM drive module Actual weight will vary slightly depending on configuration and installed modules. Size width x depth x height 12.2 inches x 9.6 inches x 1.69 inches Environmental conditions Operating...
Page 239 Features and Specifications Part III: Appendixes...
Page 240 Appendix...
Page 241: Appendix B: Power Cable Connectors
Power Cable ble Connectors The computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved United Kingdom...
Page 242 Appendix IRQ level assignments ........219 DMA channel assignments .
Page 243: Appendix C: System Resources
System m Resources This appendix lists the IRQ levels, DMA channels and I/O port addresses. IRQ level assignments The direct line to the CPU is called an Interrupt ReQuest (IRQ) level or channel. You’ll hear both terms used by technical experts. They mean the same thing.
Page 244: Dma Channel Assignments
System Resources 3.5-inch diskette drive LPT1 Real-time clock Not Available Available External PCI bus PS/2 mouse Math coprocessor Hard disk CD-ROM * MPU401 in Desk Station V Plus, if available. DMA channel assignments Direct Memory Access (DMA) allows some devices to transfer data to and from memory at high speeds, without using the CPU.
Page 245 The following table lists the computer’s DMA channel assignments. Sound system Sound system 3.5-inch diskette drive Cascade from DMA channel 1 Reserved Reserved Reserved Input/output port address assignments The CPU accesses input/output devices, such as modems, by reading from them or writing to them. Each command to read or write must specify the address (in memory) for the port.
Page 246 System Resources Port address Device/function 060-06F Keyboard controller NMI mask register 070-07F Real-time clock 080-09F DMA page register 0A0-0BF 82C59: PIC 2 0C0-0DF 82C37: DMA controller 2 0E0-0E1 PCI bus 0F0-0F7 Math coprocessor 100-1EF 170-177 CD-ROM (secondary IDE controller) 1F0-1FF Hard disk controller (primary IDE controller) Joy stick...
Page 247 Port address Device/function 280-2E7 Not used 2E8-2EF Serial port, or built-in modem (COM4) 2F0-2F7 Not used 2F8-2FF Serial port, infrared port, or built- in modem (COM2) 300-33F 340-35F Not used 360-37F Not used Controller I/O address 376-377 Secondary IDE controller 378-37F Parallel PRT 1 380-387...
Page 248 System Resources Port address Device/function 3E8-3EF Serial port, infrared port, or built- in modem (COM3) 3F0-3F7 3.5-inch diskette drive controller 3F8-3FF Serial port, infrared port, or built- in modem (COM1) 400-47F Not used 480-49F DMA high-page register 530-537 Windows sound system Not used E80-E87 Not used...
Page 249 System Resources Part III: Appendixes...
Page 250 Appendix...
Page 251: Appendix D: Video Modes
Scan Freq hor/vert is the horizontal and vertical scanning frequency in Hertz. This is for external monitors only. This table lists the video modes for the Tecra 8000 Series computer: Modes...
Page 252 Video Modes Mode (hex) Type Resolution 0, 1 VGA Text 40x25 char 2, 3 VGA Text 80x25 char 0*, 1* VGA Text 40x25 char 2*, 3* VGA Text 80x25 char 0+, 1+ VGA Text 40x25 char 2+, 3+ VGA Text 80x25 char 4, 5 VGA Grph 320x200 pels 8x8 VGA Grph 640x200 pels 8x8...
Page 253 Mode (hex) Type Resolution SVGA 800x600 pels 8x16 Grph SVGA 800x600 pels 8x16 Grph SVGA 1024x768 Grph pels SVGA 1024x768 Grph pels SVGA 1280x1024 Grph pels SVGA 1280x1024 Grph pels SVGA 640x480 pels 8x16 Grph SVGA 800x600 pels 8x16 Grph SVGA 1024x768 Grph...
Page 254 Video Modes Part III: Appendixes...
Page 255: Glossary
Glossary Acronyms Alternating Current ANSI: American National Standards Institute APM: Advanced Power Management ASCII: American Standard Code for Information Interchange AVI: Audio Video Interleaved BBS: Bulletin Board Service BIOS: Basic Input/Output System BPS: Bits Per Second CAD: Computer Aided Design CD-ROM: Compact Disc Read-Only Memory CMOS:...
Page 256 Glossary CRT: Cathode Ray Tube Direct Current DMA: Direct Memory Access DIMM: Dual Inline Memory Module DOS: Disk Operating System DPI: Dots Per Inch DRAM: Dynamic Random Access Memory DVD: Digital Versatile Disc ECC: Error-Correcting Code ECP: Enhanced Capabilities Port EDO: Extended Data Output EGA:...
Page 257 ISA: Industry Standard Architecture Kilobyte LAN: Local Area Network LCD: Liquid Crystal Display LED: Light Emitting Diode LPT1: Line Printer Port 1 (parallel port) LIM-EMS: Lotus-Intel-Microsoft Expanded Memory Specification LSI: Large Scale Integration Megabyte MIDI: Musical Instrument Digital Interface MPEG: Movie Pictures Expert Group MPU: Microprocessor Unit...
Page 258 Glossary SIMM: Single Inline Memory Module SPB: Synchronous Pipeline Burst (cache) SRAM: Static Random Access Memory STN: SuperTwist Nematic SVGA: Super Video Graphics Adapter UART: Universal Asynchronous Receiver/Transmitter UMA: Upper Memory Area UMB: Upper Memory Block URL: Universal Resource Locator USB: Universal Serial Bus VCR:...
Page 259 Advanced Power Management: An industry standard for taking advantage of a computer’s power-saving features. allocate: To assign space or resources for a specific task. Often used to refer to the use of memory or disk space. alphanumeric: Consisting of letters, numbers and other symbols you can type or print.
Page 260 Glossary basic input/output system (BIOS): A set of basic computer instructions. The BIOS, in a ROM chip, contains the information the computer needs to check the hardware and load the operating system. batch file: A file, ending with a .BAT extension, containing MS-DOS commands that you can perform together, rather than typing them one at a time.
Page 261 board: Short for printed circuit board. A thin card containing chips and other electronic components connected by metallic lines etched into the surface. Most of the basic components of a computer, such as the BIOS and memory are contained on one board, called the motherboard.
Page 262 Glossary bus speed: The speed at which the central processing unit (CPU) communicates with the other elements of the computer. For example, the speed at which data moves between the CPU and the serial ports. byte: A sequence of eight bits. A byte is the smallest addressable unit of data.
Page 263 Centronics: The printer manufacturer whose method of data transmission between a parallel printer and a computer has become an industry standard. character: Any letter, number or symbol you can use on the computer. Some characters are non-printing characters, such as a paragraph break in a word-processing program.
Page 264 Glossary compression: The translation of data to a more compact form for storage or transmission. In computer terms, files are compressed by removing repetitive and blank characters. Depending on the type of file, this can result in a size reduction of over 90%. Modems use compression to reduce the amount of time needed to send or receive a file.
Page 265 data: Information that a computer can process. The word “data” is actually plural for “datum,” meaning a single piece of information. data bits: A data communications parameter controlling the number of bits used to represent a character. If data bits = 7, the computer can generate 128 unique characters, if data bits = 8, the computer can generate 256 unique characters.
Page 266 Glossary Direct Memory Access (DMA): A dedicated channel which bypasses the Central Processing Unit (CPU) and enables a device to access memory directly. If two devices use the same DMA channel, the data required by one device overwrites the data required by the other—this is one type of hardware conflict.
Page 267 documentation: The set of manuals and/or other instructions written for the users of a computer system or program. Computer system documentation typically includes procedural and tutorial information as well as descriptions of system functions. double-click: To press the AccuPoint button or mouse button rapidly twice without moving the AccuPoint or mouse.
Page 268 Glossary enable: To turn on a computer option. erase: See delete. error-correcting code: Code designed for transmission of electronic data, that encodes data in such a way that transmission errors may be detected and corrected by examination of the encoded data on the receiving end.
Page 269 filename: A set of characters that uniquely identifies a file within its folder or directory. It consists of two parts: the actual name and the filename extension. In Windows for Workgroups and DOS, the first part of the name is limited to eight characters. In Windows 95 and Windows NT, a filename can be up to 255 characters.
Page 270 Glossary half duplex: A type of data transmission in which data flows between two devices in one direction at a time. See also full duplex. handles: Eight small boxes that appear around a graphical object when you select it. You can use the handles to change the size and shape of the object.
Page 271 HyperText Markup Language (HTML): A special coding scheme used to prepare text and graphics for access over the World Wide Web. icon: A small picture that represents a function, file, or program. infrared port: A port that allows data to be transferred by infrared signals instead of a cable.
Page 272 Glossary keyboard: The device you use to type information into the computer. Each key on the keyboard is a switch that is activated when you press it. The switch sends a specific code, representing the character printed on the key, to the processor. keyboard shortcut: A key or combination of keys that you use to perform a task instead of using a pointing device such as the AccuPoint.
Page 273 macro: A named sequence of instructions within a programming language or application. A macro may be predefined in the language or application, or you may define your own macros for procedures you use frequently. The macro name enables you to call up the sequence of instructions when you need them.
Page 274 Glossary modem: A device for transmitting computer information over telephone lines. A modem converts (modulates) digital information for transmission and also converts (demodulates) information it receives back to digital format. Many modems also interpret and execute commands received from the computer. monitor: An external device that uses rows and columns of pixels to display alphanumeric characters or graphical images.
Page 275 on line: A functional state of a peripheral in which it is ready to receive or transmit data. online: Available through the computer. Online may refer to information on the hard disk, such as online documentation or online help, or a connection, through a modem, to another computer.
Page 276 Glossary password: A unique string of characters used to identify a specific user or group of users. A password may protect system parameters from inadvertent changes, provide privacy for data, restrict the use of certain programs or prevent other people from using the computer. pathname (full path): The unique identifier for a file consisting of the filename preceded by the drive, the top-level directory or folder and any lower-level directories or folders.
Page 277 port replicator: A unit to which you can connect your notebook computer for use in the office. It replicates all the computer’s ports and provides immediate access to your external devices (such as printer, external monitor, network adapter) instead of having to connect them up each time you return to your desk.
Page 278 A Class A device is sufficient for office use. Class B is a more stringent classification applying to equipment for home use. Toshiba computers comply with Class B computing device regulations. radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent interference with radio and TV reception.
Page 279 NT, you can also use the Restart option on the Shut Down menu. See also boot. Resume Mode: A feature supplied by Toshiba that lets you turn off the power to your notebook computer without exiting from the applications you are using. Resume Mode retains your data and the details of your screen display in RAM.
Page 280 In asynchronous serial communications, one or more bits indicating the end of a block of characters. Suspend: A feature in Windows 95 or Windows NT that, like Toshiba’s Resume Mode, allows you to turn the computer off without exiting your applications and to continue from where you left off when you turn the computer on again.
Page 281 system prompt: 1) Text indicating that the operating system is ready for you to enter a command. You can enter an operating-system command or start a program from a system prompt. With some programs, you can access the system prompt and start another program without exiting the first one.
Page 282 Glossary window: A portion of the screen that can display its own application or document. wizard: A helpful online tutor that guides you through common procedures or processes, as in hardware wizard. write protection: A safeguard that physically prevents you from deleting the information on a disk or other storage media.
Page 283: Index X
Index x AC adapter plugging in AC power light 12, 27 AccuPoint 111, 121 problems AccuPoint and PS/2 mouse AccuPoint cap removing and cleaning replacing avoiding eyestrain backup battery suspending your computer batteries backup main real-time-clock (RTC) battery care of charging conserving power disposing of safely...
Page 284 Index charging the battery composite video out port computer batteries configuring hard drive passwords password conflicts connecting external monitor monitor’s video cable PS/2-compatible mouse RCA cable television video display cord connectors cover power button 7, 17 CPU fan cursor control mode light overlay hot key...
Page 285 DVD videos multiple language tracks DVD-ROM drive eject password enablers energy efficiency ergonomics expansion capability external diskette drive external display devices external keyboard key emulation problems external mouse external video device features display keyboard features and specifications feedback, microphone on an external keyboard Fn-esse starting using drag-and-drop...
Page 286 Part III: Appendixes Toshiba Time Remaining main battery, removing main battey prolonging battery life master password memory card problems memory configurations memory module...
Page 287 forgetting 160, 167 hard disk drive instant 122, 165 hot key service diskette setting Undock Password supervisor-level types Undock 159, 160 user-level PC Cards problems Plug and Play pointing device problems port composite video out expansion infrared monitor parallel PS/2 mouse/keyboard serial posture power...
Page 288 6, 13 system indicator panel technical support Toshiba InTouch Center Toshiba Companion Diskette Part III: Appendixes travel international power cord troubleshooting hardware conflicts Windows Help troubleshooting tips TSETUP turning the computer on...

This manual is also suitable for:

Tecra 8000 series

Toshiba 8000 User Manual

Chapter 1: To Begin

Chapter 2: Using Your Computer in the Office

Chapter 3: Hardware Features

Chapter 4: Using Drives

Chapter 5: Power Management

Chapter 6: Hot Keys and Function Keys

Chapter 7: Troubleshooting Guide

Part II: Technical Reference

Chapter 8: System Setup

Chapter 9: Keeping Your Files Safe

Chapter 10: Managing Your Tecra 8000 Series Computer

Appendix A: Features and Specifications

Part III: Appendixes

Appendix B: Power Cable Connectors

Appendix C: System Resources

Appendix D: Video Modes

Quick Links

Related Manuals for Toshiba 8000

Summary of Contents for Toshiba 8000