Table of Contents
Advertisement
Rear panel
1
2
OUTPUT 1
CONTROL
VIDEO INPUT
1
3
5
2
4
1
2
3
4
L
R
FRONT
1 VIDEO INPUT terminals
These are composite video input terminals of channels
1 through 4.
2 COMPONENT/VIDEO INPUT terminals
These are video input terminals of channels 5 and 6.
These input composite signal and component signal of
DVD etc.
For operation of simultaneous input of component and
composite signals, please refer to 5 OUTPUT 1
terminals (Video).
3 RGB INPUT terminals
These are RGB video input terminals of channels 7
through 10.
For the signal of a computer, etc. (15k RGB cannot be
accepted.)
4 AUDIO INPUT terminals
These are audio input terminals.
Channels 5 and 6 correspond to 5.1 channel surround.
In case of stereo input through channels 5 and 6,
connect them to FRONT L and R terminals.
For channels other than 5 and 6, only stereo input is
available.
5 OUTPUT 1 terminals (Video)
These are RGB/Y R-Y B-Y output terminal and
composite video branch output terminal.
These output video signals of the INPUT channel
selected by the OUTPUT 1 crosspoint.
When Sony's projector is connected, connect OUT-
PUT 1 with INPUT A terminal of the projector, and
plasma display is connected; connect it to INPUT 1
terminal of a plasma display.
In case of the input terminal of the projector or plasma
!¡
RS-232C
OUTPUT 2
CONTROL
REMOTE
COMPONENT/ VIDEO INPUT
6
C
/
C
/
Y
R
Y
R
R -Y
R -Y
C
/
C
/
B
B
B -Y
B -Y
VIDEO
VIDEO
AUDIO INPUT
5
6
6
7
8
CENTER
CENTER
L
L
R
R
REAR
WOOFER
FRONT
REAR
WOOFER
4
!º
PARALLEL I/O
IN
OUT
RGB INPUT
7
8
9
OUTPUT 1
9
10
R
L
L
R
FRONT
REAR
7
display is a type of D-sub 15 pin, be sure to use 5BNC
- D-sub 15 pin conversion cable.
Composite input signals of channels 1 through 6
selected by the crosspoint button are converted
internally to the component video signals and output.
At the same time, input signal also output from the
VIDEO output terminal, directly.
Y R-Y B-Y input of channels 5 and 6, and RGB input
of channels 7 through 10 are not converted, but output
as they are.
The summary of signal path are indicated in below.
• When inputting only composite signals to channels 1
through 6
COMPOSITE SIGNAL
INPUT
* The same video signal is output from RGB/Y R-Y
B-Y and VIDEO output terminals.
• When component signals and composite signals are
connected to channels 5 and 6 at the same time.
COMPOSITE SIGNAL
INPUT
COMPOSITE SIGNAL
INPUT
*Input signals of each are output as they are.
When there are both component and composite
signal outputs in DVD, etc. and when they are input
at the same time, these signals can be output to
several equipment such as a projector (component
signal) and monitor (composite signal).
Note
The component signals and RGB signals input to the
channels 5 through 10 are not converted and output to
a VIDEO output terminal.
9
3
5
OUTPUT2 MODE
OUTPUT 1
R/R - Y
G/Y
B/B - Y
PROJECTOR
MONITOR
SYNC / HD
VD
VIDEO
OUTPUT 2 / MONITOR
RGB/ Y R- Y B- Y
VIDEO
10
OUTPUT 2
/MONITOR
CENTER
~
AC IN
L
R
WOOFER
8 6
!™
RGB/Y R-Y B-Y
SIGNAL CONVERT
OUTPUT TERMINAL
RGB/Y R-Y B-Y
OUTPUT TERMINAL
VIDEO
OUTPUT TERMINAL
VIDEO
OUTPUT TERMINAL
5
Advertisement
Table of Contents
