The product is used on medium to large concrete floors. The product can be used for vibrations at a maximum reproductive harm. depth of 150 mm. The drive unit BE 20 can also be used for surface vibration. Product description Do not use the product for other tasks.
Page 3
2. Handle WARNING: This product can be dangerous 3. Lifting eye and cause serious injury or death to the 4. Electric drive unit (BE 20) operator or others. Be careful and use the 5. Rating plate product correctly. 6. Eccentric weights 7.
This product is in compliance with applicable EC directives. Note: Other symbols/decals on the product refer to special certification requirements for some markets. 1. Product type Rating plate (BE 20) 2. Product number 3. Product weight 4. Serial number 5. Manufacturer 6.
Page 5
• The operator and the employer of the operator must • Before you go away from the product, stop the know and prevent the risks during operation of the product and disconnect the power source. product. • Make sure that the power outlet voltage agrees with •...
Page 6
• Stop the product immediately if strong vibrations • Do not breathe the exhaust fumes. suddenly occurs. Do not continue the operation • Make sure that the airflow in the work area is before the cause of the increased vibrations is sufficient.
Page 7
Do a check of the safety devices regularly. If the plugs with grounded products. Power plugs without safety devices are defective, speak to your modifications, and correct power outlets decrease Husqvarna service agent. the risk of electrical shock. Fuel safety •...
It is recommended to adjust the centrifugal force before To adjust you install the drive unit on the beam. Refer to the centrifugal force (BE 20) on page 8 . 1. Put the beam on level ground. 2. Put the drive unit at the center of the beam.
Page 9
3. Tighten the screws (A). Torque to 68 Nm. To start the electric a) Start the product. Refer to drive unit (BE 20) on page 11 . b) Make sure that the beam moves smoothly. c) If the beam does not move smoothly, stop the To stop the electric drive unit product.
To do before you operate the product engine manufacturer. Maintenance • Do the daily maintenance. Refer to (BE 20) schedule on page 12 . • Make sure that there is sufficient fuel in the fuel tank. • Read the operator's manual carefully and make sure that you understand the instructions.
Page 11
Do not let the angle (A) of the • For BE 20: Change the position of the phase switch product increase to more than 8°. in the electrical connector to change the direction of rotation.
To stop the electric drive unit (BE 20) 1. Set the power switch to OFF. 2. Disconnect the power cord from the power source.
Page 13
Lubrication 13 . 8. Make sure that the O-rings and seals are not It is necessary to replace the grease on model BE 20 damaged. Replace damaged parts. each 5000 hours. Refer to the table. 1299 - 001 - 14.04.2020...
Page 14
9. Install the bearings in the flanges with a press tool or 11. Install the eccentric weights and the covers. a mallet. 10. Install the flanges and the rotor. CAUTION: Be careful when you install the rotor. The stator winding can become damaged.
Troubleshooting Problem Drive unit Cause Solution The product does Electric. There is no current. Connect the power cord correctly to the electri- not start. cal connection on the product. Do a check of the mains outlet. Fuel. The fuel level or oil level is Fill fuel and oil to the correct level.
• BE 20: Before transportation, disconnect the power cord from the power supply. Storage • BE 30: During transportation, keep the fuel valve closed and keep the engine in a vertical position to •...
Page 17
BE 20 BE 30 Power, kW/hp @rpm 0.45/0.6 @3600 2.6/3.5 @3600 Full load current, A Engine brand, type * Honda, GX120 Fuel * Unleaded gasoline, max. 10% ethanol Fuel tank capacity, l/qts 2/1.8 Oil tank capacity, l/qts 0.6/0.52 Drive unit dimensions, L×W×H mm/ft 305×341×329/1.00×1.10×1.07...
Page 18
the product is used, as well as upon the exposure time and the physical condition of the user, and the condition of the product. 1299 - 001 - 14.04.2020...
Page 19
Product dimensions (BE 30) The height (A) is 541 mm/21.2 in. for all beams. The width and length are the same as for BE 20. Refer to Product dimensions (BE 20) on page 19 . 1299 - 001 - 14.04.2020...
EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BE20 + screed BD Identification Serial numbers dating from 2020 and onwards...
Page 21
EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Concrete Compactor, Vibrating Beam Brand Husqvarna Type/Model BE30 + screed BD Identification Serial numbers dating from 2020 and onwards...