Page 3
ENGLISH 4 USER’S PART OF THE INSTRUCTION MANUAL ENGLISH 128...
Page 4
If you require another type of plug than the one fitted to the appliance, please contact a registered electrician. This appliance may only be installed by a registered electrician. If the mains cord is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard.
Page 5
Tanning sessions: how often and how long? As owner of this tanning appliance, you should give your customers the following information. For your convenience we have also included this information in a separate section that can be cut out of this manual and can be made available to customers.
Page 6
Table As is shown in the table, the first session of a tanning course should always last 5 minutes, irrespective of the sensitivity of the skin. If you think that the sessions are too long for you (e.g. because your skin feels taut and tender after the session), we advise you to reduce the length of the sessions by e.g.
Preparing for use HB604/6000SX only:The tanning appliance should be placed on a smooth, level floor. This appliance may only be installed by an authorised electrician. It requires two people to assemble and move the tanning appliance. During assembly the appliance becomes heavier and more difficult to move.We therefore advise you to assemble the appliance at the place where it will be used.
Adjusting functions Use the ¡ and ™ buttons to switch from function to function (fig. 18). The blinking symbol indicates which function is being adjusted. Options: Select • to set the time. Select ª to set the facial tanner. Select ≠ to set the body cooler. Setting the time for a tanning session Select •...
Page 9
Unfreezing set time Hold down the red O button while pressing ¢, £ and ¢ in succession.Then release the O button.The set time is no longer frozen. Set a new tanning time and press the green I button to switch the lamps on. Operating hour registration Select •...
Page 10
The starters can be removed by turning them to the left. Insert new lamps and/or starters. Always replace the tanning lamps with Philips Cleo Performance SR tube lamps. Put 100W lamps in the couch and 80W lamps in the canopy.
Troubleshooting If problems should arise with this appliance and you are unable to solve them by means of the troubleshooting guide below, please contact the nearest Philips service centre or the Philips Customer Care Centre in your country.
Page 127
ENGLISH 4 USER’S PART OF THE INSTRUCTION MANUAL ENGLISH 128...
Page 128
ENGLISH USER'S PART OF THE INSTRUCTION MANUAL Cut out and hand to users! Cut out page 127 - 131 Important Do not exceed the recommended tanning time and the maximum number of tanning hours (see 'Tanning sessions: how often and how long?').
Page 129
Duration of the tanning session For persons with very sensitive for each separate part of the skin body 7th session 10 minutes 8th session 10 minutes 9th session 10 minutes 10th session 10 minutes 10 minutes HB601/4000SX Take one tanning session a day for five to ten days.Wait at least 48 hours after the first session before taking the second session. After this 5- to 10-day course, we advise you to stop tanning for a while.
Page 130
Table As is shown in the table, the first session of a tanning course should always last 3 minutes, irrespective of the sensitivity of the skin. If you think that the sessions are too long for you (e.g. because your skin feels taut and tender after the session), we advise you to reduce the length of the sessions by e.g.
Page 131
Tanning Put on the protective goggles provided. Switch the tanning lamps on by pressing the green I button. The display shows the remaining tanning time. During the tanning session, the dot next to the time indication blinks. If you want to switch the appliance off during the tanning session, press the red O button. A few seconds after the appliance has been switched off, the cooling fans go on automatically to cool down the appliance for 3 minutes (if the standard setting has not been changed).