Related Manuals for Sony BKSI-2050
Summary of Contents for Sony BKSI-2050
- Page 1 ANALOG NTSC-4:2:2 CONVERTER BOARD BKSI-2050 ANALOG PAL-4:2:2 CONVERTER BOARD BKSI-2050P INSTALLATION MANUAL 1st Edition (Revised 1) Serial No.10001 and Higher (BKSI-2050) Serial No.10001 and Higher (BKSI-2050P)
- Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
-
Page 3: Table Of Contents
3-1. Location and Function of Connectors ..........1-4 3-2. Connection Connector ..............1-5 4. Location and Function of Switches/LEDs ............1-6 5. Specifications ....................1-9 6. ISR ......................... 1-10 6-1. Overview ..................1-10 6-2. ISR Use Environment ..............1-11 6-3. Commands ..................1-12 1(E) BKSI-2050/2050P... -
Page 4: Manual Structure
The following manual is prepared for this unit. • Maintenance Manual (Optional manual) This manual describes the information for periodic maintenance and detailed service. For obtaining the Maintenance Manual, please contact to your local Sony's sale/ service office. 2(E) BKSI-2050/2050P... -
Page 5: Installation
Installation 1. Overview The BKSI-2050 is the board that converts an analog composite video (NTSC) signal into a 4:2:2 compo- nent serial digital video signal. The BKSI-2050P is the board that converts an analog composite video (PAL) signal into a 4:2:2 component serial digital video signal. -
Page 6: Installation Of The Board
Installation Manual supplied with SIU-80. 2-1. Plug-in Board Installation Flow for installation Start Slot selection Switch setting on board SIU-80 Plug-in board installation (BKSI-2050/2050P:DEC-82/82P) Board lever Board lever Install Model label attachment Remove 4. Install the shield plate. -
Page 7: Connector Panel Installation
4. Insert the connector panel to the adaptive slot and fix the panel with two screws securing the rear blank Model label attachment panel. Connector panel installation (BKSI-2050/2050P:CN1216/1216P) SIU-80 Model label General information for installation Connector panel • The connector panel is inserted into the same slot as the plug-in board installed in the front of SIU-80. -
Page 8: Connection
3-1. Location and Function of Connectors BKSI-2050P ANALOG IN FRAME PULSE OUT DIGITAL OUT (PAL) (4:2:2-SDI) BKSI-2050P (TO BKSI-2070) PAL-4:2:2 BKSI-2050 ANALOG IN FRAME PULSE OUT DIGITAL OUT (NTSC) (4:2:2-SDI) BKSI-2050 (TO BKSI-2070) NTSC-4:2:2 1 ANALOG IN (analog signal input) connector (BNC type): Received the analog composite video signal. -
Page 9: Connection Connector
If any cable is connected to the connectors on the connector panel when installing or servicing, use the connector with listed below or equivalent. BKSI-2050/2050P Matching Connector/Cable Panel Indication Connector Connector/Cable Sony Part No. ANALOG IN BNC 75Ω BNC 75Ω 1-560-069-11 FRAME PULSE OUT BELDEN 8281 cable... -
Page 10: Location And Function Of Switches/Leds
Lights red ; When not receiving the input signal or 3 S2: SETUP REMOVE switch (BKSI-2050 Only) when judging that the input signal is not Selected to remove the SETUP if or not when the received. - Page 11 FREEZE 335. mode is selected. The factory settings are shown below. 0 S200-1 and S200-2 (Factory use only) (The marks indicate the positions of the switch knobs.) Factory setting : Fixed to OFF. 1-7(E) BKSI-2050/2050P...
- Page 12 S601-5, S601-6, and S601-7: Line setting switch for SETUP REMOTE Selected the line that is removed the SETUP within the vertical blanking period. (BKSI-2050 only.) S601-7: ON Removed the SETUP of the lines 10 and later of the odd field.
-
Page 13: Specifications
14 W Input/output Analog input ANALOG IN connector(BNC type) (1) 1.0 V p-p, 75 Ω BKSI-2050 : NTSC analog composite video signal, with loop-through output BKSI-2050P : PAL analog composite video signal, with loop-through output Digital output DIGITAL OUT connector(BNC type) (4) 0.8 V p-p, 75 Ω... -
Page 14: Isr
The BKSI-2050/2050P corresponds to a ISR(Interactive Status Reporting) function. Using this function, the status of the BKSI-2050/2050P or the contents of a generated error can be intensively monitored and managed on the monitor screen of a personal computer. The data displayed on the monitor screen can be stored or printed as a file. -
Page 15: Isr Use Environment
ROM name) 6-2. ISR Use Environment The ISR function is controlled by Sony application program software. For the program software, use, installation, and operation of a personal computer in which this program software can be used, consult with your local Sony’s sale/service office. -
Page 16: Commands
6. ISR 6-3. Commands BKSI-2050/2050P supports the following commands. Command Support Support *RST; *IDN?; Only Power Cycled on *FLAGS?; *STATUS?; *CMDERR?; *MSG?####; *UPLOAD?TYPE; TYPE=VSETTBL Response Support Support *ATN : OPC; *ATN : CMDERR; *ATN : QRESP; SONY Private Command Support Support SETUP?;... - Page 17 The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any...
- Page 18 BKSI-2050P (CE) Printed in Japan Sony Corporation BKSI-2050 (UCJ) J, E 1997. 6 16 Broadcast Products Company 3-189-229-02 ©1995 Published by Broadcast Products Company...